Specifications

ManualsBrandsVivotek ManualsSecurity CamerasIP7153

Summary of content (148 pages)

PAGE 1
PAGE 2
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Table of Contents Overview ��3 Read Before Use ��3 Package Contents ��
PAGE 3
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Overview VIVOTEK’s IP7153 (PoE) / 7154 (WLAN), equipped with a progressive scan CCD sensor, delivers superior-quality, crystal-clear video for professional surveillance applications such as monitoring banks, airports, parking lots, and traffic control, etc. It can capture razor-sharp, high-resolution images of moving objects that traditional interlacedscan techniques cannot achieve.
PAGE 4
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Physical Description Front Panel Antenna (IP7154 only) Light Sensor Built-in Microphone Status LED Back Panel Antenna (IP7154 only) Microphone In Ethernet 10/100 RJ45 Socket General I/O Terminal Block External/Internal Microphone Switch Audio Out Power Cord Socket Recessed Reset Button Lens Focus Controller Zoom Controller General I/O Terminal Block This Network Camera provides a general I/O terminal block which is used to connect e
PAGE 5
VIVOTEK - A Leading Provider of Multimedia Communication Solutions DI/DO Diagram Refer to the following illustration for the connection method. 12V PIN 1 Power+12V PIN 2 Digital output +12V PIN 3 Digital input PIN 4 Ground Status LED The LED indicates the status of the Network Camera. Item 1 2 3 4 5 6 LED status All LED light => All LED unlight => Steady Red => Steady Red + Blink Green once per sec. Steady Red All LED unlight Steady Red + Blink Green every 1 sec. Blink Red every 0.15 sec.
PAGE 6
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Hardware Reset Status LED Recessed Reset Button The reset button is used to reset the system or restore the factory default settings. Sometimes resetting the system can return the camera to normal operation. If the system problems remain after reset, restore the factory settings and install again. Reset: Press and release the indented reset button with a paper clip or thin object. Wait for the Network Camera to reboot.
PAGE 7
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Network Deployment Setting up the Network Camera over the Internet This section explains how to configure the Network Camera to an Internet connection. 1. If you have external devices such as sensors and alarms, make the connection from the general I/O terminal block. 2. Connect the camera to a switch via Ethernet cable. 3. Connect the supplied power cable from the Network Camera to a power outlet.
PAGE 8
VIVOTEK - A Leading Provider of Multimedia Communication Solutions 2. In this case, if the Local Area Network (LAN) IP address of your Network Camera is 192.168.0.3, please forward the following ports for the Network Camera on the router. ■ HTTP port ■ RTSP port ■ RTP port for audio ■ RTCP port for audio ■ RTP port for video ■ RTCP port for video If you have changed the port numbers on the Network page, please open the ports accordingly on your router.
PAGE 9
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Set up the Network Camera through Power over Ethernet (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, which allows it to be powered via a single Ethernet cable. If your switch/router supports PoE, refer to the following illustration to connect the Network Camera to a PoE-enabled switch/router.
PAGE 10
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Set up the Network Camera through Wireless Connection (IP7154 only) 1. Check the SSID for your wireless access point (AP). 2. Go to the IP7154 Configuration page > Advanced mode > Wireless LAN. 3. Type in the SSID the same as your AP. 4. Select the Wireless mode as “Infrastructure”. 5. Click Save. The Network Camera will reboot. 6. Wait for the live image to be reloaded to your browser.
PAGE 11
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Software Installation Installation Wizard 2 (IW2), free-bundled software included on the product CD, helps you set up your Network Camera on the LAN. 1. Install IW2 under the Software Utility directory from the software CD. Double click the IW2 shortcut on your desktop to launch the program. 2. The program will conduct an analysis of your network environment.
PAGE 12
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Ready to Use 1. Access the Network Camera from the LAN. 2. Retrieve live video through a web browser or recording software.
PAGE 13
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Accessing the Network Camera This chapter explains how to access the Network Camera through web browsers, RTSP players, 3GPP-compatible mobile devices, and VIVOTEK recording software. Using Web Browsers Use Installation Wizard 2 (IW2) to access to the Network Cameras on the LAN. If your network environment is not a LAN, follow these steps to access the Netwotk Camera: 1. Launch your web browser (ex.
PAGE 14
VIVOTEK - A Leading Provider of Multimedia Communication Solutions ► By default, the Network Camera is not password-protected. To prevent unauthorized access, it is highly recommended to set a password for the Network Camera. For more information about how to enable password protection, please refer to Security on page 27. ► If you see a dialog box indicating that your security settings prohibit running ActiveX ® Controls, please enable the ActiveX ® Controls for your browser. 1.
PAGE 15
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Using RTSP Players To view the MPEG-4 streaming media using RTSP players, you can use one of the following players that support RTSP streaming. Quick Time Player Real Player VLC media player 1. Launch the RTSP player. mpegable Player 2. Choose File > Open URL. A URL dialog box will pop up. 3.
PAGE 16
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Using 3GPP-compatible Mobile Devices To view the streaming media through 3GPP-compatible mobile devices, make sure the Network Camera can be accessed over the Internet. For more information on how to set up the Network Camera over the Internet, please refer to Setup the Network Camera over the Internet on page 7. To utilize this feature, please check the following settings on your Network Camera: 1.
PAGE 17
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Using VIVOTEK Recording Software The product software CD also contains recording software, allowing simultaneous monitoring and video recording for multiple Network Cameras. Please install the recording software; then launch the program to add the Network Camera to the Channel list. For detailed information about how to use the recording software, please refer to the user’s manual of the software or download it from http://www.vivotek.com.
PAGE 18
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Main Page This chapter explains the layout of the main page. It is composed of the following sections: VIVOTEK INC. Logo, Host Name, Camera Control Area, Configuration Area, and Live Video Window. VIVOTEK INC. Logo Host Name Camera Control Area Live View Window Configuration Area VIVOTEK INC. Logo Click this logo to visit the VIVOTEK website. Host Name The host name can be customized to fit your needs.
PAGE 19
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Live Video Window ■ The following window is displayed when the video mode is set to MPEG-4: MPEG-4 Protocol and Media Options Video Title Title and Time Time Video 17:08:56 2008/06/25 Video and Audio Control Buttons Video Title: The video title can be configured. For more information, please refer to Video Settings on page 52. MPEG-4 Protocol and Media Options: The transmission protocol and media options for MPEG-4 video streaming.
PAGE 20
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Volume: When the local computer. Mute function is not activated, move the slider bar to adjust the volume on the Mute: Turn off the volume on the local computer. The button becomes the clicking the Mute button. Audio On button after Talk: Click this button to talk to people around the Network Camera. Audio will project from again to end talking the external speaker connected to the Network Camera. Click this button transmission.
PAGE 21
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Digital Zoom: Click and uncheck “Disable digital zoom” to enable the zoom operation. The navigation screen indicates the part of the image being magnified. To control the zoom level, drag the slider bar. To move to a different area you want to magnify, drag the navigation screen. Start MP4 Recording: Click this button to record video clips in MP4 file format to your computer. Stop MP4 Recording button to end recording.
PAGE 22
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Client Settings This chapter explains how to select the stream transmission mode and saving options on the local computer. When completed with the settings on this page, click Save on the page bottom to enable the settings. MPEG-4 Media Options Select to stream video or audio data or both. This is enabled only when the video mode is set to MPEG-4.
PAGE 23
VIVOTEK - A Leading Provider of Multimedia Communication Solutions MP4 Saving Options Users can record live video as they are watching it by clicking page. Here, you can specify the storage destination and file name. Start MP4 Recording on the main Folder: Specify a storage destination for the recorded video files. File Name Prefix: Enter the text that will be appended to the front of the video file name.
PAGE 24
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Configuration Click Configuration on the main page to enter the camera setting pages. Note that only Administrators can access the configuration page. VIVOTEK offers an easy-to-use user interface that helps you set up your network camera with minimal effort. To simplify the setting procedure, two types of user interfaces are available: Advanced Mode for professional users and Basic Mode for entry-level users.
PAGE 25
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Advanced Mode Configuration List Click to switch to Basic Mode Firmware Version Each function on the configuration list will be explained in the following sections. Those functions that are displayed only in Advanced Mode are marked with Advanced Mode . If you want to set up advanced functions, please click [Advanced Mode] on the bottom of the configuration list to quickly switch over.
PAGE 26
VIVOTEK - A Leading Provider of Multimedia Communication Solutions System Time Keep current date and time: Select this option to preserve the current date and time of the Network Camera. The Network Camera’s internal real-time clock maintains the date and time even when the power of the system is turned off. Sync with computer time: Select this option to synchronize the date and time of the Network Camera with the local computer. The read-only date and time of the PC is displayed as updated.
PAGE 27
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Security This section explains how to enable password protection and create multiple accounts. Root Password The administrator account name is “root”, which is permanent and can not be deleted. If you want to add more accounts in the Manage User column, please apply the password for the “root” account first. 1. Type the password identically in both text boxes, then click Save to enable password protection. 2.
PAGE 28
VIVOTEK - A Leading Provider of Multimedia Communication Solutions HTTPS (Hypertext Transfer Protocol over SSL) Advanced Mode This section explains how to enable authentication and encrypted communication over SSL (Secure Socket Layer). It helps protect streaming data transmission over the Internet on higher security level. Enable HTTPS Check this item to enable HTTPS communication, then select a connection option: "HTTP & HTTPS" or "HTTPS only".
PAGE 29
VIVOTEK - A Leading Provider of Multimedia Communication Solutions 4. The Certificate Information will automatically de displayed in the third column as shown below. You can click Property to view detailed information about the certificate. 5. Click Home to return to the main page. Change the address from “http://” to “https://“ in the address bar and press Enter on your keyboard. Some Security Alert dialogs will pop up. Click OK or Yes to enable HTTPS. https:// https://192.168.5.151/index.
PAGE 30
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Create self-signed certificate manually 1. Select this option. 2. Click Create to open the Create Certificate page, then click Save to generate the certificate. 3. The Certificate Information will automatically be displayed in the third column as shown below. You can click Property to see detailed information about the certificate.
PAGE 31
VIVOTEK - A Leading Provider of Multimedia Communication Solutions 3. If you see the following Information bar, click OK and click on the Information bar at the top of the page to allow pop-ups. 4. The pop-up window shows an example of a certificate request.
PAGE 32
VIVOTEK - A Leading Provider of Multimedia Communication Solutions 5. Look for a trusted certificate authority that issues digital certificates. Enroll the Network Camera. Wait for the certificate authority to issue a SSL certificate; click Browse... to search for the issued certificate, then click Upload in the second column. NOTE ► How do I cancel the HTTPS settings? 1. Uncheck Enable HTTPS secure connection in the first column and click Save; a warning dialog will pop up. 2. Click OK to disable HTTPS.
PAGE 33
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Network This section explains how to configure a wired network connection for the Network Camera. Network Type LAN Select this option when the Network Camera is deployed on a local area network (LAN) and is intended to be accessed by local computers. The default setting for the Network Type is LAN. Rememer to click Save when you complete the Network setting.
PAGE 34
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Network Camera (192.168.5.151) Enable UPnP port forwarding: To access the Network Camera from the Internet, select this option to allow the Network Camera to open ports on the router automatically so that video streams can be sent out from a LAN. To utilize of this feature, make sure that your router supports UPnPTM and it is activated.
PAGE 35
VIVOTEK - A Leading Provider of Multimedia Communication Solutions ► Steps to enable the UPnP TM user interface on your computer: Note that you must log on to the computer as a system administrator to install the UPnP TM components. 1. Go to Start, click Control Panel, then click Add or Remove Programs. 2. In the Add or Remove Programs dialog box, click Add/Remove Windows Components. 3. In the Windows Components Wizard dialog box, select Networking Services and click Details.
PAGE 36
VIVOTEK - A Leading Provider of Multimedia Communication Solutions 4. In the Networking Services dialog box, select Universal Plug and Play and click OK. 5. Click Next in the following window. 6. Click Finish. UPnP TM is enabled. ► How does UPnP TM work? UPnP TM networking technology provides automatic IP configuration and dynamic discovery of devices added to a network.
PAGE 37
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Enable IPv6 Select this option and click Save to enable IPv6 settings. Please note that this only works if your network environment and hardware equipment support IPv6. The browser should be Microsoft® Internet Explorer 6.5, Mozilla Firefox 3.0 or above. When IPv6 is enabled, by default, the network camera will listen to router advertisements and be assigned with a link-local IPv6 address accordingly.
PAGE 38
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Please follow the steps below to link to an IPv6 address: 1. Open your web browser. 2. Enter the link-global or link-local IPv6 address in the address bar of your web browser. 3. The format should be: http://[2001:0c08:2500:0002:0202:d1ff:fe04:65f4]/ IPv6 address 4. Press Enter on the keyboard or click Refresh button to refresh the webpage.
PAGE 39
VIVOTEK - A Leading Provider of Multimedia Communication Solutions HTTP Advanced Mode To utilize HTTP authentication, make sure that your have set a password for the Network Camera first; please refer to Security on page 27 for details. Authentication: Depending on your network security requirements, the Network Camera provides two types of security settings for an HTTP transaction: basic and digest.
PAGE 40
VIVOTEK - A Leading Provider of Multimedia Communication Solutions URL command -- http://:/ For example, when the Access name for stream 2 is set to video2.mjpg: 1. Launch Mozilla Firefox or Netscape. 2. Type the URL command in the address bar. Press Enter. 3. The JPEG images will be displayed in your web browser. http://192.168.5.151/video2.
PAGE 41
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Note that as JPEG only transmits a series of JPEG images to the client, to enable the two-way audio function, make sure the video mode is set to “MPEG-4” on the Audio and Video Settings page and the media option is set to “Video and Audio” on the Client Settings page. Please refer to Client Settings on page 22 and Audio and Video Settings on page 51.
PAGE 42
VIVOTEK - A Leading Provider of Multimedia Communication Solutions RTSP Streaming To utilize RTSP streaming authentication, make sure that you have set a password for the Network Camera first; please refer to Security on page 27 for details. Authentication: Depending on your network security requirements, the Network Camera provides three types of security settings for streaming via RTSP protocol: disable, basic, and digest.
PAGE 43
VIVOTEK - A Leading Provider of Multimedia Communication Solutions RTSP port /RTP port for video, audio/ RTCP port for video, audio ■ RTSP (Real-Time Streaming Protocol) controls the delivery of streaming media. By default, the port number is set to 554. ■ The RTP (Real-time Transport Protocol) is used to deliver video and audio data to the clients. By default, the RTP port for video is set to 5556 and the RTP port for audio is set to 5558.
PAGE 44
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Wireless LAN (IP7154 only) SSID (Service Set Identifier): This is the name that identifies a wireless network. Access Points and wireless clients attempting to connect to a specific WLAN (Wireless Local Area Network) must use the same SSID. The default setting is “default”. Note: The maximum length for an SSID is 32 single-byte characters and cannot consist of “, <, >, or blank spaces.
PAGE 45
VIVOTEK - A Leading Provider of Multimedia Communication Solutions 2. WEP (Wired Equivalent Privacy): This allows communication only with other devices with identical WEP settings. ■ Authentication Mode: Choose one of the following modes. The default setting is “Open”. Open – Communicates the key across the network. Shared – Allows communication only with other devices with identical WEP settings. ■ Key length: The administrator can set the key length to 64 or 128 bits. The default setting is “64 bits”.
PAGE 46
VIVOTEK - A Leading Provider of Multimedia Communication Solutions 3. WPA-PSK: Use WPA (Wi-Fi Protected Access) pre-shared key. More secure than WEP, the Wi-Fi Alliance developed WPA (Wi-Fi Protected Access) in 2003 to address WEP’s weaknesses. Improvements included TKIP, which changes the encryption key for each data transmission. ■ Algorithm: Choose one of the following algorithms for WPA-PSK and WPA2-PSK modes. TKIP (Temporal Key Integrity Protocol): A security protocol used in IEEE 802.
PAGE 47
VIVOTEK - A Leading Provider of Multimedia Communication Solutions DDNS This section explains how to configure the dynamic domain name service for the Network Camera. DDNS is a service that allows your Network Camera, especially when assigned with a dynamic IP address, to have a fixed host and domain name. DDNS: Dynamic domain name service Enable DDNS: Select this option to enable the DDNS setting. Provider: Select a DDNS provider from the provider drop-down list. VIVOTEK offers Safe100.
PAGE 48
VIVOTEK - A Leading Provider of Multimedia Communication Solutions [Register] Successfully Your account information has been mailed to registered e-mail address 4. Select Enable DDNS and click Save to enable the setting. ■ CustomSafe100 VIVOTEK offers documents to establish a CustomSafe100 DDNS server for distributors and system integrators. You can use CustomSafe100 to register a dynamic domain name if your distributor or system integrators offer such services. 1.
PAGE 49
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Access List Advanced Mode This section explains how to control access permission by verifying the client PC’s IP address. General Settings Maximum number of concurrent streaming connection(s) limited to: Simultaneous live viewing for 1~10 clients (including stream 1 and stream 2). The default value is 10.
PAGE 50
VIVOTEK - A Leading Provider of Multimedia Communication Solutions ■ Refresh: Click this button to refresh all current connections. ■ Add to deny list: You can select entries from the Connection Status list and add them to the Deny List to deny access. Please note that those checked connections will only be disconnected temporarily and will automatically try to re-link again (IE Explore or Quick Time Player).
PAGE 51
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Network: This rule allows the user to assign a network address and corresponding subnet mask to the Allow/Deny List. For example: IP address 192.168.2.x will be bolcked. Range: This rule allows the user to assign a range of IP addresses to the Allow/Deny List. This rule is only applied to IPv4. For example: ■ Delete Allowed/Denied list: In the Delete Allowed List or Delete Denied List column, make a selection and click Delete.
PAGE 52
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Audio and Video This section explains how to cofigure the audio and video settings of the Network Camera. It is composed of the following two columns: Video Settings and Audio Settings. Video Settings Video title: Enter a name that will be displayed on the title bar of the live video. Video Title Title and Time Video 17:08:56 2008/06/25 Color: Select to display color or black/white video streams.
PAGE 53
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Overlay title and time stamp on video: Select this option to place the video title and time on the video streams. Note that when the frame size is set to 176 x 144 as shown in the picture below, only the time will be stamped on the video streams. 17:08:56 2008/06/25 Image Settings Advanced Mode Click Image settings to open the Image Settings page.
PAGE 54
VIVOTEK - A Leading Provider of Multimedia Communication Solutions White balance: Adjust the value for the best color temperature. ■ Auto The Network Camera automatically adjusts the color temperature of the light in response to different light sources. The white balance setting defaults to Auto and works well in most situations. ■ Keep current value Follow the steps below to manually set the white balance to compensate for the ambient lighting conditions. 1. Set the White balance to Auto and click Save.
PAGE 55
VIVOTEK - A Leading Provider of Multimedia Communication Solutions NOTE ► Up to 5 privacy mask windows can be set up on the same screen. ► If you want to delete the privacy mask window, please click the ‘x’ on the upper right-hand corner of the window. Sensor Settings Advanced Mode Click Sensor Settings to open the Sensor Settings page. On this page, you can set the exposure level, and AGC (Auto Gain Control) settings.
PAGE 56
VIVOTEK - A Leading Provider of Multimedia Communication Solutions If you want to configure another sensor setting for day/night/schedule mode, please click Profile to open the Sensor Settings Profile Settings page as shown below. Please follow the steps beolw to setup a profile: 1. Check Enable this profile. 2. Select the applied mode: Day mode, Night mode, or schedule mode. Please manually enter a range of time if you choose Schedule mode. 3. Configure Exposure settings in the second column.
PAGE 57
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Video quality settings for stream 1 / stream 2 Advanced Mode The Network Camera offers two choices of video compression standards for real-time viewing: MPEG-4 and MJPEG. Click the items to display the detailed configuration settings. You can set up two seperate streams for the Network Camera for different viewing devices.
PAGE 58
VIVOTEK - A Leading Provider of Multimedia Communication Solutions If JPEG mode is selected, the Network Camera continuously sends JPEG images to the client, producing a moving effect similar to a filmstrip. Every single JPEG image transmitted guarantees the same image quality, which in turn comes at the expense of variable bandwidth usage. Because the media contents are a combination of JPEG images, no audio data is transmitted to the client.
PAGE 59
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Day/Night Settings Switch to B/W in night mode Select this to enable the Network Camera to automatically switch to B/W during night mode. IR cut filter With a removable IR-cut filter, this Network Camera can automatically remove the filter to let IR light into the sensor during low light conditions. ■ Auto mode The Network Camera automatically removes the filter by judging the level of ambient light.
PAGE 60
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Audio Settings Mute: Select this option to disable audio transmission from the Network Camera to all clients. Note that if mute mode is turned on, no audio data will be transmitted even if audio transmission is enabled on the Client Settings page. In that case, the following message is displayed: Internal microphone input gain: Select the gain of the internal audio input according to ambient conditions.
PAGE 61
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Motion Detection This section explains how to configure the Network Camera to enable motion detection. A total of three motion detection windows can be configured. Motion Detection Setting 1: For normal situations Follow the steps below to enable motion detection: Follow the steps below to enable motion detection: Motion Detection Setting 2: For special situations 1. Click New to add a new motion detection window. 2.
PAGE 62
VIVOTEK - A Leading Provider of Multimedia Communication Solutions A green bar indicates that even though motions have been detected, the event has not been triggered because the image variations still fall under the defined threshold. Percentage = 30% If you want to configure other motion detection settings for day/night/schedule mode, please click Profile to open the Motion Detection Profile Settings page as shown below. A total of three motion detection windows can be configured on this page as well.
PAGE 63
VIVOTEK - A Leading Provider of Multimedia Communication Solutions NOTE ► How does motion detection work? A C B D There are two motion detection parameters: Sensitivity and Percentage. In the illustration above, frame A and frame B are two sequential images. Pixel differences between the two frames are detected and highlighted in gray (frame C) and will be compared with the sensitivity setting. Sensitivity is a value that expresses the sensitivity to moving objects.
PAGE 64
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Camera Control This section explains how to control the Network Camera’s Pan/Tilt/Zoom operation by connecting to a PTZ driver or scanner via RS485 interface. RS485 Settings Disable: Select this option to disable this function. PTZ camera: Select this option to enable PTZ operation. To utilize this feature, please connect the Network Camera to a PTZ driver or scanner via RS485 interface first.
PAGE 65
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Preset Positions If you select DynaDome/SmartDOME, Lilin PIH-7x00, or Pelco D protocol as the PTZ driver and click the Save button, the Preset Position button will be enabled. Click Preset Position to open the settings page. You can also select preset positions for the camera to patrol. A total of 20 preset positions can be configured. Please follow the steps below to preset a position: 1.
PAGE 66
VIVOTEK - A Leading Provider of Multimedia Communication Solutions ■ The Camera Control Panel and Preset Positions will be displayed on the home page: ■ Click Go to: The Network Camera will move to the selected preset position.
PAGE 67
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Patrol Settings You can also select preset positions for the Network Camera to patrol. Please follow the steps below to set up a patrol schedule: 1. Click a preset location on the list and click Select. 2. The selected preset location will be displayed on the Source list. 3. Set the Dwelling time for the preset location during auto patrol. You can also manually enter a value in the blank and click Update. 4.
PAGE 68
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Custom Command If Custom Camera (scanner) is selected as the PTZ driver, the Preset Position and PTZ Control Panel on the main page will be disabled. You will need to configure command buttons to control the PTZ scanner. Click Custom Command to open the Custom Command page to set the commands in the Control Settings session. Please refer to your PTZ scanner user's manual to enter the commands in the following fields.
PAGE 69
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Camera Tampering Detection This section explains how to set up camera temper detection. With tamper detection, the camera is capable of detecting incidents such as redirection, blocking or defocusing, or even spray paint. Please follow the steps below to set up the camera tamper detection function: 1. Check Enable camera tampering detection. 2. Enter the tamper trigger duration. (10 sec. ~ 10 min.
PAGE 70
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Homepage Layout Advanced Mode This section explains how to set up your own customized homepage layout. Preview This column shows the settings of your hompage layout. You can manually select the background and font colors in Theme Options (the third column on this page). The settings will be displayed automatically in this Preview field.
PAGE 71
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Theme Options Here you can change the color of your homepage layout. There are three types of preset patterns for you to choose from. The new layout will simultaneously appear in the Preview filed. Click Save to enable the settings.
PAGE 72
VIVOTEK - A Leading Provider of Multimedia Communication Solutions ■ Follow the steps below to set up the customed homepage: 1. Click Custom on the left column. 2. Click the field where you want to change the color on the right column. Color Selector Custom Pattern 3. The palette window will pop up as shown below. 2 3 1 4 4. Drag the slider bar and click on the left square to select a desired color. 5. The selected color will be displayed in the corresponding fields and in the Preview column. 6.
PAGE 73
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Application Advanced Mode This section explains how to configure the Network Camera to responds to particular situations (event). A typical application is that when a motion is detected, the Network Camera sends buffered images to an FTP server or e-mail address as notifications. In the illustration on the right, an event can be Action triggered by many sources, such as motion detection Event Trigger or external digital input devices.
PAGE 74
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Event Settings In the Event Settings column, click Add to open the Event Settings page. On this page, you can arrange three elements -- Trigger, Schedule, and Action to set an event. A total of 3 event settings can be configured. Event name: Enter a name for the event setting. Enable this event: Select this option to enable the event setting. Priority: Select the relative importance of this event (High, Normal, or Low).
PAGE 75
VIVOTEK - A Leading Provider of Multimedia Communication Solutions An event is an action initiated by a user-defined trigger source; it is the causal arrangement of the following three elements: Trigger, Event Schedule, and Action. Trigger This is the cause or stimulus which defines when to trigger the Network Camera. The trigger source can be configured to use the Network Camera’s built-in motion detection mechanism or external digital input devices.
PAGE 76
VIVOTEK - A Leading Provider of Multimedia Communication Solutions ■ Recording notify This option allows the Network Camera to trigger when the recording disk is full or when recording starts to rewrite older data. If you want receive Recording notify message, please refer to page 84 for detailed information. ■ Camera tampering detection This option allows the Network Camera to trigger when the camera detects that is is being tampered with.
PAGE 77
VIVOTEK - A Leading Provider of Multimedia Communication Solutions To set an event with recorded video or snapshots, it is necessary to configure the server and media settings so that the Network Camera will know what action to take (such as which server to send the media files to) when a trigger is activated. ■ Add Server / Add Media Click Add Server to configure Server Settings. For more information, please refer to Server Settings on page 79. Click Add Media to configure Media Settings.
PAGE 78
VIVOTEK - A Leading Provider of Multimedia Communication Solutions When completed, click Save to enable the settings and click Close to exit Event Settings page. The new event settings / server settings / media settings will appear in the event drop-down list on the Application page. Here is an example of the Application page with an event setting: When the Event Status is ON, once an event is triggered by motion detection, the Network Camera will automatically send snapshots via e-mail.
PAGE 79
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Server Settings Click Add Server on Event Settings page to open the Server Setting page. On this page, you can specify where the notification messages are sent when a trigger is activated. A total of 5 server settings can be configured. Server name: Enter a name for the server setting. Server Type There are four choices of server types available: Email, FTP, HTTP, and Network storage.
PAGE 80
VIVOTEK - A Leading Provider of Multimedia Communication Solutions FTP: Select to send the media files to an FTP server when a trigger is activated. ■ Server address: Enter the domain name or IP address of the FTP server. ■ Server port By default, the FTP server port is set to 21. It can also be assigned to another port number between 1025 and 65535. ■ User name: Enter the login name of the FTP account. ■ Password: Enter the password of the FTP account.
PAGE 81
VIVOTEK - A Leading Provider of Multimedia Communication Solutions HTTP: Select to send the media files to an HTTP server when a trigger is activated. ■ URL: Enter the URL of the HTTP server. ■ User name: Enter the user name if necessary. ■ Password: Enter the password if necessary. To verify if the HTTP settings are correctly configured, click Test. The result will be shown in a pop-up window as below. If successful, you will receive a test.txt file on the HTTP server.
PAGE 82
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Media Settings Click Add Media on the Event Settings page to open the Media Settings page. On this page, you can specify the type of media that will be sent when a trigger is activated. A total of 5 media settings can be configured. Media name: Enter a name for the media setting. Media Type There are three choices of media types available: Snapshot, Video Clip, and System log. Select the item to display the detailed configuration options.
PAGE 83
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Video clip: Select to send video clips when a trigger is activated. ■ Source: Select to record video clips from stream 1 or stream 2. ■ Pre-event recording The Network Camera has a buffer area; it temporarily holds data up to a certain limit. Enter a number to decide the duration of recording before a trigger is activated. Up to 9 seconds can be set. ■ Maximum duration Specify the maximum recording duration in seconds.
PAGE 84
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Recording notify message: Select to send a recording notification message when a trigger is activated. The following is an example of a recording notification message (.txt file), which shows a list of deleted previously-recorded data due to cycle recording. When completed, click Save to enable the settings and click Close to exit this page. The new media settings will appear on the Event Settings page.
PAGE 85
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Click 20081120 to open the directory: The format is: HH (24r) Click to open the file list for that hour Click to go back to the previous level of the directory Click to delete selected items Click to delete all recorded data The format is: File name prefix + Minute (mm) You can set up the file name prefix on Media Settings page. Please refer to page 82 for detailed information.
PAGE 86
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Recording Advanced Mode This section explains how to configure the recording settings for the Network Camera. Recording Settings NOTE ► Before setting up this page, please set up the Network Storage on the Server Settings page first. Network Storage Setting Click Server to open the Server Settings page and follow the steps below to set up: 1. Fill in the information for your server.
PAGE 87
VIVOTEK - A Leading Provider of Multimedia Communication Solutions If successful, you will receive a test.txt file on the network storage server. 3. Enter a server name. 4. Click Save to complete the settings and click Close to exit the page. Recording Settings Click Add to open the recording setting page. In this page, you can define the recording source, recording schedule and recording capacity. A total of 2 recording settings can be configured. Recording name: Enter a name for the recording setting.
PAGE 88
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Source: Select the recording source (stream 1 or stream 2). Recording Schedule: Specify the recording duration. ■ Select the days of the week. ■ Select the recording start and end times in 24-hr time format. Destination: You can select the network storage that was set up for the recorded video files. Capacity: You can choose either the entire free space available or limit the recording size.
PAGE 89
VIVOTEK - A Leading Provider of Multimedia Communication Solutions System Log Advanced Mode This section explains how to configure the Network Camera to send the system log to the remote server as backup. Remote Log You can configure the Network Camera to send the system log file to a remote server as a log backup. Before utilizing this feature, it is suggested that the user install a log-recording tool to receive system log messages from the Network Camera. An example is Kiwi Syslog Daemon.
PAGE 90
VIVOTEK - A Leading Provider of Multimedia Communication Solutions View Parameters Advanced Mode The View Parameters page lists the entire system’s parameters in alphabetical order. If you need technical assistance, please provide the information listed on this page.
PAGE 91
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Maintenance This chapter explains how to restore the Network Camera to factory default, upgrade firmware version, etc. Reboot This feature allows you to reboot the Network Camera, which takes about one minute to complete. When completed, the live video page will be displayed in your browser. The following message will be displayed during the reboot process.
PAGE 92
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Export / Upload Files Advanced Mode This feature allows you to Export / Upload daylight saving time rules, custom language files, and setting backup files. Export daylight saving time configuration file: Click to set the start and end time of DST. Follow the steps below to export: 1. In the Export files column, click Export to export the daylight saving time configuration file from the Network Camera. 2.
PAGE 93
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Upload daylight saving time rule: Click Browse… and specify the XML file to upload. If the incorrect date and time are assigned, you will see the following warning message when uploading the file to the Network Camera. The following message is displayed when attempting to upload an incorrect file format. Export language file: Click to export language strings.
PAGE 94
VIVOTEK - A Leading Provider of Multimedia Communication Solutions The following message is displayed when the upgrade has succeeded. The following message is displayed when you have selected an incorrect firmware file. Starting firmware upgrade... Do not power down the server during the upgrade. The server will restart automatically after the upgrade is completed. This will take about 1 - 5 minutes.
PAGE 95
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Appendix URL Commands for the Network Camera Overview For some customers who already have their own web site or web control application, the Network Camera/Video Server can be easily integrated through URL syntax. This section specifies the external HTTP-based application programming interface. The HTTP-based camera interface provides the functionality to request a single image, control camera functions (PTZ, output relay etc.
PAGE 96
VIVOTEK - A Leading Provider of Multimedia Communication Solutions General CGI URL Syntax and Parameters CGI parameters are written in lower-case and as one word without any underscores or other separators. When the CGI request includes internal camera parameters, these parameters must be written exactly as they are named in the camera or video server. The CGIs are organized in functionally-related directories under the cgi-bin directory. The file extension .cgi is required.
PAGE 97
VIVOTEK - A Leading Provider of Multimedia Communication Solutions [&…] http:///cgi-bin/operator/getparam.cgi?[] [&…] http:///cgi-bin/admin/getparam.cgi?[] [&…] Where the should be [_] or [.]. If you do not specify any parameters, all the parameters on the server will be returned. If you specify only , the parameters of the related group will be returned.
PAGE 98
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Set Server Parameter Values Note: The access right depends on the URL directory. Method: GET/POST Syntax: http:///cgi-bin/anonymous/setparam.cgi? = [&=…][&update=][&return=] http:///cgi-bin/viewer/setparam.cgi? = [&=…][&update=] [&return=] http:///cgi-bin/operator/setparam.
PAGE 99
VIVOTEK - A Leading Provider of Multimedia Communication Solutions =\r\n [] Only the parameters that you set and are readable will be returned. Example: Set the IP address of server to 192.168.0.123: Request: http://myserver/cgi-bin/admin/setparam.cgi?videoin_c0_text=HelloWorld Response: HTTP/1.0 200 OK\r\n Content-Type: text/html\r\n Context-Length: 33\r\n \r\n network.ipaddress=192.168.0.
PAGE 100
VIVOTEK - A Leading Provider of Multimedia Communication Solutions integer primary key SQLite data type. A 32-bit signed integer. The value is assigned a unique integer by the server. text SQLite data type. The value is a text string, stored using the database encoding (UTF-8, UTF-16BE or UTF-16-LE). NOTE: The camera should not be restarted when parameters are changed.
PAGE 101
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Indiana -160: GMT-04:00 Atlantic Time, Canada, Caracas, La Paz, Santiago -140: GMT-03:30 Newfoundland -120: GMT-03:00 Brasilia, Buenos Aires, Georgetown, Greenland -80: GMT-02:00 Mid-Atlantic -40: GMT-01:00 Azores, Cape_Verde_IS.
PAGE 102
VIVOTEK - A Leading Provider of Multimedia Communication Solutions 400: GMT 10:00 Brisbane, Canberra, Melbourne, Sydney, Guam, Vladivostok 440: GMT 11:00 Magadan, Solomon Is., New Caledonia 480: GMT 12:00 Aucklan, Wellington, Fiji, Kamchatka, Marshall Is. 520: GMT 13:00 Nuku'Alofa daylight_enable 6/6 Enable automatic daylight saving time in time zone. daylight_dstactual 6/7 mode daylight_auto_begi Check if current time is under daylight saving time.
PAGE 103
VIVOTEK - A Leading Provider of Multimedia Communication Solutions This command can cooperate with other “restoreexceptXYZ” commands. When cooperating with others, the system parameters will be restored to default values except for a union of combined results. restoreexceptlang 7/6 Restore the system parameters to default values except the custom language file the user has uploaded. This command can cooperate with other “restoreexceptXYZ” commands.
PAGE 104
VIVOTEK - A Leading Provider of Multimedia Communication Solutions (get/set) videoactualmodulation ntsc, N/A 4/7 The actual modulation type pal di_i<0~(ndi-1)> (videoin.type=0). 0 1/7 0 => Inactive, normal 1 => Active, triggered do_i<0~ndi-1)> 0 1/7 0 => Inactive, normal 1 => Active, triggered onlinenum_rtsp integer 0 6/7 Current number of RTSP connections. onlinenum_httppush integer 0 6/7 Current number of HTTP push server connections.
PAGE 105
VIVOTEK - A Leading Provider of Multimedia Communication Solutions privilege operator, admin Group: network NAME VALUE SECURITY DESCRIPTION (get/set) type lan, 6/6 Network connection type. pppoe preprocess 0~15 6/6 Stop related process before setting port value. resetip 6/6 1 => Get ipaddress, subnet, router, dns1, dns2 from DHCP server at next reboot. 0 => Use preset ipaddress, subnet, rounter, dns1, and dns2. ipaddress 6/6 IP address of server.
PAGE 106
VIVOTEK - A Leading Provider of Multimedia Communication Solutions (get/set) port 80, 1025 ~ 65535 6/6 HTTP port. alternateport 1025~65535 6/6 Alternate HTTP port. authmode basic, 1/6 HTTP authentication mode. 1/6 HTTP server push access name for stream 1. digest s0_accessname string[32] (capability.protocol.spush_mjpeg =1 and video.stream.count>0) s1_accessname string[32] 1/6 HTTP server push access name for stream 2. (capability.protocol.spush_mjpeg =1 and video.stream.
PAGE 107
VIVOTEK - A Leading Provider of Multimedia Communication Solutions (get/set) alwaysmulticast 4/4 Enable always multicast. ipaddress 4/4 Multicast IP address. videoport 1025 ~ 65535 4/4 Multicast video port. audioport 1025 ~ 65535 4/4 Multicast audio port. ttl 1 ~ 255 4/4 Mutlicast time to live value. Subgroup of network: sip NAME VALUE SECURITY DESCRIPTION (get/set) port 554, 1025 ~ 65535 6/6 SIP port. (capability.protocol.
PAGE 108
VIVOTEK - A Leading Provider of Multimedia Communication Solutions txrate 10~13 or France 1~14 All NONE, 1M, 2M, 6/6 Maximum boolean rate in Mbps. 6/6 Encryption method (product dependent): 5.5M, 11M, 6M, 9M, 12M, 18M, 24M, 36M, 48M, 54M, Auto encrypt 0~3 0=> NONE, 1 => WEP, 2 => WPA, 3 => WPA2PSK authmode OPEN, SHARED 6/6 Authentication mode. keylength 64, 128 6/6 Key length in bits. keyformat HEX, ASCII 6/6 Key1 ~ key4 presentation format. keyselect 1~4 6/6 Default key number.
PAGE 109
VIVOTEK - A Leading Provider of Multimedia Communication Solutions (get/set) enable 6/6 Enable access list filtering. admin_enable 6/6 Enable administrator IP address. admin_ip String[44] 6/6 Administrator IP address. maxconnection 1~10 6/6 Maximum number of concurrent streaming connection(s). allow_i<0~9>_start 1.0.0.0 ~ 6/6 Allowed starting IPv4 address for connection. 6/6 Allowed ending IPv4 address for connection.
PAGE 110
VIVOTEK - A Leading Provider of Multimedia Communication Solutions (get/set) color 0, 1 4/4 0 =>monochrome 1 => color flip 4/4 Flip the image. mirror 4/4 Mirror the image.
PAGE 111
VIVOTEK - A Leading Provider of Multimedia Communication Solutions 176x120, CIF, 352x240, 4CIF, 704x480 PAL => QCIF, 176x144, CIF, 352x288, 4CIF, 704x576 VS => QCIF, 176x120, 176x144, CIF, 352x240, 352x288, 4CIF, 704x480, 704x576 s<0~(m-1)>_mpeg4_i 250, 500, ntraperiod 1000, 2000, 4/4 Intra frame period in milliseconds.
PAGE 112
VIVOTEK - A Leading Provider of Multimedia Communication Solutions qvalue customize input “mpeg4_quant = 0” (for MPEG-4). s<0~(m-1)>_mjpeg_q 0~5 4/4 uant Quality of JPEG video. 0 is the customized manual input setting. 1 = worst quality, 5 = best quality. s<0~(m-1)>_mjpeg_ 1~25, maxframe 26~30 (only 4/4 Set maximum frame rate in fps (for JPEG).
PAGE 113
VIVOTEK - A Leading Provider of Multimedia Communication Solutions boostmic 0, 1 4/4 Enable microphone boost. s<0~(m-1)>_codectype aac4, gamr 4/4 Set audio codec type for input. s<0~(m-1)>_aac4_bitrate 16000, 4/4 Set AAC4 bitrate in bps. 4/4 Set AMR bitrate in bps.
PAGE 114
VIVOTEK - A Leading Provider of Multimedia Communication Solutions sharpness videoin_whitebalance auto, according to mode settings. 4/4 Preview of white balance adjustment of image manual videoin_restoreatwb according to mode settings. 0, 1~ 4/4 Restore white balance adjustment of image according to mode settings.
PAGE 115
VIVOTEK - A Leading Provider of Multimedia Communication Solutions profile_i<0~(m-1)>_win_i<0~2>_enable 4/4 Enable motion window. profile_i<0~(m-1)>_win_i<0~2>_name string[14] 4/4 Name of motion window. profile_i<0~(m-1)>_win_i<0~2>_left 0 ~ 320 4/4 Left coordinate of window position. profile_i<0~(m-1)>_win_i<0~2>_top 0 ~ 240 4/4 Top coordinate of window position. profile_i<0~(m-1)>_win_i<0~2>_width 0 ~ 320 4/4 Width of motion detection window.
PAGE 116
VIVOTEK - A Leading Provider of Multimedia Communication Solutions _passw string[64] 6/6 Your password or key to login to the DDNS ordkey _server service provider. string[128] 6/6 The server name for safe100. name (This field only exists if the provider is customsafe100) Group: upnppresentation NAME VALUE SECURITY DESCRIPTION (get/set) enable 6/6 Enable or disable the UPNP presentation service.
PAGE 117
VIVOTEK - A Leading Provider of Multimedia Communication Solutions panspeed -5 ~ 5 0 1/4 Pan speed tiltspeed -5 ~ 5 0 1/4 Tilt speed zoomspeed -5 ~ 5 0 1/4 Zoom speed autospeed -5 ~ 5 0 1/4 Auto pan speed focusspeed -5 ~ 5 0 1/4 Auto focus speed dwelling 0 ~ 9999 0 1/4 Dwelling time during patrol axisx -104 ~ 104 0 1/7 Axis X coordinate, used internally. axisy -15 ~ 28 0 1/7 Axis Y coordinate, used internally.
PAGE 118
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Bit 0 => move home Bit 1 => move up Bit 2 => move upper right Bit 3 => move right Bit 4 => move lower right Bit 5 => move down Bit 6 => move lower left Bit 7 => move left Bit 8 => move upper left Bit 9 => set pan speed Bit 10 => set tilt speed Bit 11 => zoom wide Bit 12 => zoom tele Bit 13 => set zoom speed Bit 14 => focus far Bit 15 => focus near Bit 16 => focus auto Bit 17 => set focus speed Bit 18 => iris open Bit 19 => iris close Bit 20
PAGE 119
VIVOTEK - A Leading Provider of Multimedia Communication Solutions 00,38400,57600, 115200 databit 5,6,7,8 4/4 Data bits in a character frame. paritybit none, 4/4 For error checking. 4/4 1 odd, even stopbit 1,2 2-1.5 , data bit is 5 2-2 uartmode rs485, 4/4 RS485 or RS232. 4/4 Set this flag to true to apply change in UART rs232 uartreset configuration. customdrvcmd_i<0~ string[128] 1/4 PTZ command for custom camera. string[40] 1/4 Additional PTZ command name.
PAGE 120
VIVOTEK - A Leading Provider of Multimedia Communication Solutions theme_color_controlbackgroun string[7] 1/6 Background color of control area. theme_color_configbackground string[7] 1/6 Background color of configuration area. theme_color_videobackground string[7] 1/6 Background color of video area. theme_color_case string[7] 1/6 Frame color d Group: privacymask_c<0~(n-1)> for n channel product NAME VALUE SECURITY DESCRIPTION (get/set) enable 4/4 Enable privacy mask.
PAGE 121
VIVOTEK - A Leading Provider of Multimedia Communication Solutions naudioin 0, 0/7 Number of audio inputs. 0/7 Number of audio outputs. naudioout 0, nvideoin 0/7 Number of video inputs. nmediastream 0/7 Number of media stream per channels. nvideosetting 0/7 Number of video settings per channel. naudiosetting 0/7 Number of audio settings per channel.
PAGE 122
VIVOTEK - A Leading Provider of Multimedia Communication Solutions separately as follows: Bit 0 => Support pan. Bit 1 => Support pan in UI. Bit 2 => External or built-in pan function; 0(built-in), 1(external). lens_tilt 0/7 A 32-bit integer, each bit can be set separately as follows: Bit 0 => Support tilt. Bit 1 => Support tilt in UI. Bit 2 => External or built-in tilt function; 0(built-in), 1(external).
PAGE 123
VIVOTEK - A Leading Provider of Multimedia Communication Solutions ction protocol_maxmegacon connections . 0/7 nection protocol_rtp_multicast The maximum megapixel streaming connections. 0/7 _ Indicate whether to support scalable multicast. scalable protocol_rtp_multicast 0/7 _ Indicate whether to support backchannel multicast. backchannel protocol_rtp_tcp 0/7 Indicate whether to support RTP over TCP.
PAGE 124
VIVOTEK - A Leading Provider of Multimedia Communication Solutions audio_linein 0/7 Indicate whether to support external line input. audio_lineout 0/7 Indicate whether to support line output. audio_headphoneout 0/7 Indicate whether to support headphone output. audioin_codec
PAGE 125
VIVOTEK - A Leading Provider of Multimedia Communication Solutions product can be upgraded to VVXX. (TCVV<->TCXX is excepted) evctrlchannel 0/7 Indicate whether to support HTTP tunnel for event/control transfer. joystick 0/7 Indicate whether to support joystick control. storage_dbenabled 0/7 Media files are indexed in database.
PAGE 126
VIVOTEK - A Leading Provider of Multimedia Communication Solutions mdwin 6/6 Indicate which motion detection windows detect. This field is required when trigger condition is “md”. One bit represents one window. The LSB indicates the 1st window. For example, to detect the 1st and 3rd windows, set mdwin as 5. mdwin0 6/6 Indicate which motion detection windows of profile 1 detect. inter 1~999 6/6 Interval of snapshots in minutes.
PAGE 127
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Group: server_i<0~4> PARAMETER VALUE SECURITY DESCRIPTION (get/set) name string[40] 6/6 Identification of this entry type email, 6/6 Indicate the server type: ftp, “email” = email server http, “ftp” = FTP server ns “http” = HTTP server “ns” = network storage http_url string[128] 6/6 URL of the HTTP server to upload. http_username string[64] 6/6 Username to log in to the server.
PAGE 128
VIVOTEK - A Leading Provider of Multimedia Communication Solutions (get/set) name string[40] 6/6 Identification of this entry type snapshot, 6/6 Media type to send to the server or store on the systemlog, server. videoclip, recordmsg snapshot_source 6/6 Indicates the source of the media stream: 0 = first stream 1 = second stream Etc. snapshot_prefix string[16] 6/6 Indicate the prefix of the filename.
PAGE 129
VIVOTEK - A Leading Provider of Multimedia Communication Solutions limitsize 0,1 6/6 0: Entire free space mechanism 1: Limit recording size mechanism cyclic 0,1 6/6 0: Disable cyclic recording 1: Enable cyclic recording notify 0,1 6/6 0: Disable recording notification 1: Enable recording notification notifyserver 0~31 6/6 Indicate which notification server is scheduled. One bit represents one application server (server_i0~i4). bit0 (LSB) = server_i0. bit1 = server_i1. bit2 = server_i2.
PAGE 130
VIVOTEK - A Leading Provider of Multimedia Communication Solutions cffolder string[128] 6/6 Folder name. Group: https (product dependent) NAME VALUE SECURITY DESCRIPTION (get/set) enable 6/6 To enable or disable secure HTTP. policy 6/6 If the value is 1, it will force HTTP connection redirect to HTTPS connection method auto, 6/6 auto => Create self-signed certificate manual, automatically. install manual => Create self-signed certificate manually.
PAGE 131
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Where state is 0 or 1; “0” means inactive or normal state, while “1” means active or triggered state. PARAMETER VALUE DESCRIPTION do 0, 1 0 – Inactive, normal state 1 – Active, triggered state return Redirect to the page after the parameter is assigned. The can be a full URL path or relative path according to the current path.
PAGE 132
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Request: http://myserver/cgi-bin/dido/getdi.cgi?di1 Response: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: 7\r\n \r\n di1=1\r\n . Query Status of the Digital Output Note: This request requires Viewer privileges. Method: GET/POST Syntax: http:///cgi-bin/dido/getdo.cgi?[do0][&do1][&do2][&do3] If no parameter is specified, all the digital output statuses will be returned. Return: HTTP/1.
PAGE 133
VIVOTEK - A Leading Provider of Multimedia Communication Solutions \r\n do1=1\r\n Capture Single Snapshot Note: This request requires Normal User privileges. Method: GET/POST Syntax: http:///cgi-bin/viewer/video.jpg?[channel=][&resolution=] [&quality=] If the user requests a size larger than all stream settings on the server, this request will fail. PARAMETER VALUE DEFAULT DESCRIPTION channel 0~(n-1) 0 The channel number of the video source.
PAGE 134
VIVOTEK - A Leading Provider of Multimedia Communication Solutions PARAMETER VALUE DESCRIPTION method Add Add an account to the server. When using this method, the “username” field is necessary. It will use the default value of other fields if not specified. Delete Remove an account from the server. When using this method, the “username” field is necessary, and others are ignored. edit Modify the account password and privilege.
PAGE 135
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Configuration File (optional) Note: This request requires Administrator privileges. Method: GET/POST Syntax: http:///cgi-bin/admin/configfile.cgi?[format=] Server will return the most up-to-date configuration file. PARAMETER VALUE DEFAULT DESCRIPTION format xml xml Format for the config file. Return: HTTP/1.
PAGE 136
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Camera Control (capability.ptzenabled=1) Note: This request requires Viewer privileges. Method: GET/POST Syntax: http:///cgi-bin/viewer/camctrl.
PAGE 137
VIVOTEK - A Leading Provider of Multimedia Communication Solutions vy vs 0~7 Set the speed of movement, “0” means stop. focus auto Auto focus. far Focus on further distance. near Focus on closer distance. auto Let the Network Camera control iris size. open Manually control the iris for bigger size. close Manually control the iris for smaller size. speedlink 0~4 Issue speed link command.
PAGE 138
VIVOTEK - A Leading Provider of Multimedia Communication Solutions System Information Note: This request requires Normal User privileges. (obsolete) Method: GET/POST Syntax: http:///cgi-bin/sysinfo.cgi Server will return the system information. In HTTP API version 2, the CapVersion will be 0200. All fields in the previous version (0100) are obsolete. Please use “getparam.cgi?capability” instead. Return: HTTP/1.
PAGE 139
VIVOTEK - A Leading Provider of Multimedia Communication Solutions PARAMETER VALUE DESCRIPTION addpos channel <0~(n-1)> Channel of the video source. delpos return Redirect to the page after the parameter is assigned. The can be a full URL path or relative path according to the current path.
PAGE 140
VIVOTEK - A Leading Provider of Multimedia Communication Solutions start The starting IP address to add or to delete. end The ending IP address to add or to delete. index The start position to add or to delete. return after the parameter is assigned. The page> can be a full URL path or relative path according to the current path. If you omit this parameter, it will redirect to an empty page.
PAGE 141
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Event/Control HTTP Tunnel Channel Note: This request requires Administrator privileges. Method: GET and POST Syntax: http:///cgi-bin/admin/ctrlevent.cgi ------------------------------------------------------------------------GET /cgi-bin/admin/ctrlevent.
PAGE 142
VIVOTEK - A Leading Provider of Multimedia Communication Solutions “m” is the stream number. “network_accessname_<0~(m-1)>” is the accessname for stream “1” to stream “m”. Please refer to the “subgroup of network: rtsp” for setting the accessname of SDP. You can get the SDP by HTTP GET. Open the Network Stream Note: This request requires Viewer access privileges.
PAGE 143
VIVOTEK - A Leading Provider of Multimedia Communication Solutions wait 1 ~ 65535 Wait time in milliseconds before read data. read 1 ~ 128 The data length in bytes to read. The read data will be in the return page. Return: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: \r\n \r\n \r\n Where hexadecimal data is digits from 0 ~ 9, A ~ F. Storage managements (capability.storage.
PAGE 144
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Please embrace your input value with single quotes� Ex. mediaType=’videoclip’ Support trigger types are product dependent. destPath Optional. Indicate the file location in camera. Please embrace your input value with single quotes. Ex. destPath =’/mnt/auto/CF/NCMF/abc.mp4’ resolution Optional. Indicate the media file resolution. Please embrace your input value with single quotes. Ex.
PAGE 145
VIVOTEK - A Leading Provider of Multimedia Communication Solutions http:///cgi-bin/admin/lsctrl.cgi?cmd=search&triggerType=’motion’+OR+’di’+OR+’seq’&trig gerTime=’2008-01-01 00:00:00’+TO+’2008-01-01 23:59:59’ Command: delete PARAMETER VALUE DESCRIPTION label Required. Identify the designated record. Ex. label=1 Ex. Delete records whose key numbers are 1, 4, and 8. http:///cgi-bin/admin/lsctrl.
PAGE 146
Technical Specifications Models ．IP7153 (PoE) ．IP7154 (WLAN) System ．CPU: VVTK-1000 SoC ．Flash: 8MB ．RAM: 64MB ．Embedded OS: Linux 2.4 Specifications Lens ．CS-mount, vari-focal, f = 2.9 ~ 8.2 mm, F1.0, auto-iris ．IR Corrected ．Removable IR-cut filter for day & night function Angle of View ． 26.7° ~ 69.0° (horizontal) ． 20.0° ~ 51.0° (vertical) Shutter Time ．1/5 sec. to 1/15,000 sec. Image Sensor ．SONY 1/4” progressive scan CCD sensor in VGA resolution Minimum Illumination ．0.2 Lux / F1.
PAGE 147
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Technology License Notice MPEG-4 AAC Technology THIS PRODUCT IS LICENSED UNDER THE MPEG-4 AAC AUDIO PATENT LICENSE. THIS PRODUCT MAY NOT BE DECOMPILED, REVERSE-ENGINEERED OR COPIED, EXCEPT WITH REGARD TO PC SOFTWARE, OF WHICH YOU MAY MAKE SINGLE COPIES FOR ARCHIVAL PURPOSES. FOR MORE INFORMATION, PLEASE REFER TO HTTP://WWW.VIALICENSING.COM.
PAGE 148
VIVOTEK - A Leading Provider of Multimedia Communication Solutions Electromagnetic Compatibility (EMC) FCC Statement This device compiles with FCC Rules Part 15. Operation is subject to the following two conditions. ■ This device may not cause harmful interference, and ■ This device must accept any interference received, including interference that may cause undesired operation.