FD8361L Fixed Dome Network Camera Quick Installation Guide English P/N:625012601G Rev. 1.1 簡中 日本語 Français Español Deutsch Português Italiano IR Illuminators • 3-axis • Video Cropping • ePTZ All specifications are subject to change without notice. Copyright c 2012 VIVOTEK INC. All rights reserved. VIVOTEK INC. VIVOTEK USA, INC. |T: +886-2-82455282| F: +886-2-82455532| E: sales@vivotek.com |T: 408-773-8686| F: 408-773-8298| E: salesusa@vivotek.com 6F, No.192, Lien-Cheng Rd.
English Warning Before Installation Power off the Network Camera as soon as smoke or unusual odors are detected. Refer to your user's manual for the operating temperature. Contact your distributor in the event of occurrence. Do not place the Network Camera on unsteady surfaces. Do not touch the Network Camera during a lightning storm. Do not insert sharp or tiny objects into the Network Camera. Do not drop the Network Camera.
1 : sales@vivotek.com Bottom Base FD8361L Alignment Sticker / Ceiling Hole Template Sticker Drill hole Ceiling Hole Template Sticker L-type Hex Key Wrench / RJ45 Female/Female Coupler / Silica Gel / Screws Quick Installation Guide / Warranty Card FD8361L Software CD Fixed Dome Network Camera Quick Installation Guide English 繁中 簡中 日本語 Français Español Deutsch Português Italiano Türkçe Polski Русский Česky Svenska IR Illuminators • 3-axis • Video Cropping • ePTZ t notice. rved.
English 2 Physical Description Inner View IR LEDs (18 units, distance 20m) Light Sensor Rotation Adjustment Screw Tilt Adjustment Screw Pan Adjustment Screw NTSC/PAL Video Output Switch Vari-focal Lens (f= 3~9 mm) SD/SDHC Card Slot Status LED Recessed Reset Button Focus Controller Zoom Controller BNC Video Output AC 24V Terminal Block AC24V AC24V Ethernet 10/100 RJ45 Plug Ground Operating environment: -20° ~ 50°C When the temparature inside the Network Camera reaches over 50°C, the fan will operat
Outer View IP66-rated Vandal-proof Dome Cover AC24V AC24V Camera Base c b a IP66-rated Vandal-proof Bottom Base c Record the MAC address under the camera base before installing the camera. Network Camera Model No: FD8361L RoHS V I MAC:0002D1083236 CLASS A a This device complies with part 15 of the FCC rules.
English 3 Hardware Installation First, use a screwdriver to loose the three screws and detach the dome cover from the camera base. Then, follow the steps below to install the camera to either a ceiling or a wall. AC24V AC24V Ceiling mount (with the bottom base) 1. Attach the supplied alignment sticker to the ceiling. 2. Using the 10 circles on the sticker, drill at least 2 pilot holes symmetrically on each side into the ceiling. Then hammer the four supplied plastic anchors into the holes. 3.
Wall mount (with the bottom base) 1. Attach the supplied alignment sticker to the wall. 2. Using the 10 circles on the sticker, drill at least 2 pilot holes symmetrically on each side into the wall. Then hammer the four supplied plastic anchors into the holes. 3. Using the four holes on the bottom base, insert the four supplied screws to corresponding holes and secure the bottom base with a screwdriver. 4. Feed the cables through hole A or B.
English Drop-ceiling mount (without the bottom base) 1. Attach the supplied ceiling hole template sticker to the ceiling. 2. Open a hole along the inner circle of the sticker. 3. Using the 3 circles on the sticker, drill 3 pilot holes into the ceiling. Then hammer the three supplied plastic anchors into the holes. 4. Mount the Network Camera to the ceiling and feed the cables through. 5.
Power over Ethernet (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled switch via Ethernet cable. AC24V AC24V POWER COLLISION 1 2 3 4 5 LINK RECEIVE PARTITION PoE Switch When using a non-PoE switch Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE switch.
English 5 Assigning an IP Address 1. Install “Installation Wizard 2” from the Software Utility directory on the software CD. 2. The program will conduct an analysis of your network environment. After your network is analyzed, please click on the “Next” button to continue the program. Installation Wizard 2 3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras on the same LAN. 4. After searching, the main installer window will pop up.
6 Ready to Use 1. Access the Network Camera from the LAN. 2. Retrieve live video through web browser or recording software. For further setup, please refer to the user's manual on the software CD.
English 7 Adjusting the Lens Based on the live image retrieved from the camera, adjust the camera lens by doing the following: To adjust the viewing angle -- 3-axis mechanism design 1. Loosen the pan adjustment screw and then turn the lens module left and right. Upon completion, tighten the screw. 2. Loosen the tilt adjustment screws on both side of the camera and then turn the lens module up and down. Upon completion, tighten the screws. 3.
8 Completion 1. Rotate the black cover inside the dome cover to fit the lens shooting direction. 2. Attach the dome cover to the camera. 3. Secure the three dome screws with the supplied screwdriver. Finally, make sure all parts of the camera are securely installed.
FD8361L Fixed Dome Network Camera Quick Installation Guide English P/N:625012601G Rev. 1.1 簡中 日本語 Français Español Deutsch Português Italiano IR Illuminators • 3-axis • Video Cropping • ePTZ All specifications are subject to change without notice. Copyright c 2012 VIVOTEK INC. All rights reserved. VIVOTEK INC. VIVOTEK USA, INC. |T: +886-2-82455282| F: +886-2-82455532| E: sales@vivotek.com |T: 408-773-8686| F: 408-773-8298| E: salesusa@vivotek.com 6F, No.192, Lien-Cheng Rd.
