User manual

ManualsBrandsVIVOTEK ManualsIP CCTV SystemsLAN IP camera 2,8 mm

User’s Manual

H.264 • 2MP/5MP • 30M IR • P-iris • Smart Stream • Smart IR

Fixed Dome

Network Camera

FD816B-H(T)/HF2

FD8182-T/F2

Rev. 1.1

Summary of content (314 pages)

PAGE 1
FD816B-H(T)/HF2 Dome FD8182-T/F2 Fixed Network Camera User’s Manual H.264 • 2MP/5MP • 30M IR • P-iris • Smart Stream • Smart IR Rev. 1.
PAGE 2
VIVOTEK Table of Contents Overview ��3 Revision History ��3 Read Before Use ��
PAGE 3
VIVOTEK Appendix �� 138 URL Commands for the Network Camera �� 138 Technical Specifications �� 230 Technology License Notice ��
PAGE 4
VIVOTEK Read Before Use The use of surveillance devices may be prohibited by law in your country. The Network Camera is not only a high-performance web-ready camera but can also be part of a flexible surveillance system. It is the user’s responsibility to ensure that the operation of such devices is legal before installing this unit for its intended use. It is important to first verify that all contents received are complete according to the Package Contents listed below.
PAGE 5
VIVOTEK Physical Description IR LEDs Motorized or fixed lens Microphone PIR Terminal block SD/SDHC/SDXC Card Slot Dome cover release tab RJ45 Ethernet port Reset button NOTE: The "T" and "HT" models have an auto-focus motorized lens.
PAGE 6
VIVOTEK Hardware Installation 1. Jot down the camera's MAC address for later reference. This is especially important if you install numerous cameras at an installation site. 1 Network Camera Model No: XXXXXX MAC: 0002D1083236 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Pat.
PAGE 7
VIVOTEK 3. Plan your installation by speculating on the effective range and direction of PIR sensor. 3 121° 5M 77.3° 5M 4. Attach the included alignment sticker to a preferred location. Drill holes for mounting screws and if preferred, drill a routing hole.
PAGE 8
VIVOTEK If preferred, use a cutting plier to remove the platic tab on the pre-cut routing hole, and pass cables through the hole. 5. If applied, connect DI/DO wires, 12V DC power, or audio wires to the terminal block. 5 78 56 4 3 12 9 10 The DO output is 12V, 30V max., and the max. load is 50mA. The DI voltage range is +-30V.
PAGE 9
VIVOTEK 6. Install the "Installation Wizard 2" software utility on your software CD. The program will search for VIVOTEK Video Receivers, Video Servers or Network Cameras on the same LAN. Double-click on the camera’s MAC address to open a browser management session with the camera. 6 IW2 LAN 00-02-D1-73-02-02 192.168.5.151 FD8168 0002D1730202 Browser 7. With a live view displayed on your laptop, adjust the zoom and focus to obtain an optimal image.
PAGE 10
VIVOTEK 8. Install the dome cover by aligning the crescent cutout with the protruding tab on the base plate. 8 9. Remove the protection membrane from the dome cover. LED Definitions Item LED status LED De`finitions 1 2 3 4 5 Steady Red Red LED off Green LED off Steady Red and Green LED blinks every 1 sec. Green LED blinks every 1 sec. and RED LED blinks consecutively every 0.15 sec. Green and RED blink every 0.15 sec, Green and RED light on, then blink again.
PAGE 11
VIVOTEK Hardware Reset Reset Button The reset button is used to reset the system or restore the factory default settings. Sometimes resetting the system can return the camera to normal operation. If the system problems remain after reset, restore the factory settings and install again. Reset: Press the recessed reset button. Wait for the Network Camera to reboot. Restore: Press and hold the reset button until the status LED rapidly blinks. Note that all settings will be restored to factory default.
PAGE 12
VIVOTEK Network Deployment General Connection (PoE) When using a PoE switch The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable. Follow the illustration below to connect the Network Camera to a PoE switch via an Ethernet cable. 802.3af PoE Switch When using a non-PoE switch Use a PoE power injector (optional) to connect between the Network Camera and a nonPoE switch. PoE Power Injector (optional) Non-PoE Switch NOTE: 1.
PAGE 13
VIVOTEK Internet connection via a router Before setting up the Network Camera over the Internet, make sure you have a router and follow the steps below. 1. Connect your Network Camera behind a router, the Internet environment is illustrated below. Regarding how to obtain your IP address, please refer to Software Installation on page 15 for details. IP address : 192.168.0.3 WAN (Wide Area Network ) Internet Router IP address : from ISP POWER COLLISION 1 2 3 4 5 Subnet mask : 255.255.255.
PAGE 14
VIVOTEK Configure the router, virtual server or firewall, so that the router can forward any data coming into a preconfigured port number to a network camera on the private network, and allow data from the camera to be transmitted to the outside of the network over the same path. From Forward to 122.146.57.120:8000 192.168.2.10:80 122.146.57.120:8001 192.168.2.11:80 ... ... When properly configured, you can access a camera behind the router using the HTTP request such as: http://122.146.57.
PAGE 15
VIVOTEK Software Installation Installation Wizard 2 (IW2), a software included in the product CD, helps you set up your Network Camera on the LAN. IW2 1. Install IW2 under the Software Utility directory from the software CD. Double-click the IW2 shortcut on your desktop to launch the program. Installation Wizard 2 2. The program will conduct an analysis of your network environment. After your network environment is analyzed, please click Next to continue the program. 3.
PAGE 16
VIVOTEK Ready to Use 1. A browser session with the Network Camera should prompt as shown below. 2. You should be able to see live video from your camera. You may also install the 32-channel recording software from the software CD in a deployment consisting of multiple cameras. For its installation details, please refer to its related documents.
PAGE 17
VIVOTEK Auto Focus (for Motorized Lens Models only) On the web console, visit the Configuration > Image > Focus window. Perform the Auto Focus function for best image focus. Focus here refers to the Remote Focus, applicable to Network Cameras that are equipped with a stepping motor lens. The automated focus adjustment function eliminates the needs to physically adjust camera focus.
PAGE 18
VIVOTEK Accessing the Network Camera This chapter explains how to access the Network Camera through web browsers, RTSP players, 3GPP-compatible mobile devices, and VIVOTEK recording software. Using Web Browsers Use Installation Wizard 2 (IW2) to access the Network Cameras on LAN. If your network environment is not a LAN, follow these steps to access the Netwotk Camera: 1. Launch your web browser (e.g., Microsoft® Internet Explorer or Mozilla Firefox). 2.
PAGE 19
VIVOTEK ► By default, the Network Camera is not password-protected. To prevent unauthorized access, it is highly recommended to set a password for the Network Camera. For more information about how to enable password protection, please refer to Security on page 87. ► If you see a dialog box indicating that your security settings prohibit running ActiveX ® Controls, please enable the ActiveX ® Controls for your browser. 1. Choose Tools > Internet Options > Security > Custom Level. 2.
PAGE 20
VIVOTEK IMPORTANT: • Currently the Network Camera utilizes 32-bit ActiveX plugin. You CAN NOT open a management/view session with the camera using a 64-bit IE browser. • If you encounter this problem, try execute the Iexplore.exe program from C:\Windows\ SysWOW64. A 32-bit version of IE browser will be installed. • On Windows 7, the 32-bit explorer browser can be accessed from here: C:\Program Files (x86)\Internet Explorer\iexplore.
PAGE 21
VIVOTEK Using RTSP Players To view the streaming media using RTSP players, you can use one of the following players that support RTSP streaming. Quick Time Player VLC media player VLC media player 1. Launch the RTSP player. mpegable Player 2. Choose File > Open URL. A URL dialog box will pop up. 3.
PAGE 22
VIVOTEK Using 3GPP-compatible Mobile Devices To view the streaming media through 3GPP-compatible mobile devices, make sure the Network Camera can be accessed over the Internet. For more information on how to set up the Network Camera over the Internet, please refer to Setup the Network Camera over the Internet on page 12. To utilize this feature, please check the following settings on your Network Camera: 1.
PAGE 23
VIVOTEK Using VIVOTEK Recording Software The product software CD also contains an ST7501 recording software, allowing simultaneous monitoring and video recording for multiple Network Cameras. Please install the recording software; then launch the program to add the Network Camera to the Channel list. For detailed information about how to use the recording software, please refer to the user’s manual of the software or download it from http://www.vivotek.com. Tips: 1.
PAGE 24
VIVOTEK Main Page This chapter explains the layout of the main page. It is composed of the following sections: VIVOTEK INC. Logo, Host Name, Camera Control Area, Configuration Area, Menu, and Live Video Window. Resize Buttons VIVOTEK INC. Logo Host Name Configuration Area Camera Control Area Hide Button Live View Window VIVOTEK INC. Logo Click this logo to visit the VIVOTEK website. Host Name The host name can be customized to fit your needs.
PAGE 25
VIVOTEK Configuration Area Client Settings: Click this button to access the client setting page. For more information, please refer to Client Settings on page 29. Configuration: Click this button to access the configuration page of the Network Camera. It is suggested that a password be applied to the Network Camera so that only the administrator can configure the Network Camera. For more information, please refer to Configuration on page 34.
PAGE 26
VIVOTEK PTZ Panel: This Network Camera supports “digital“ (e-PTZ) pan/tilt/zoom control, which allows roaming a smaller view frame within a large view frame. Please refer to PTZ settiings on page 100 for detailed information. Global View: Click on this item to display the Global View window. The Global View window contains a full view image (the largest frame size of the captured video) and a floating frame (the viewing region of the current video stream).
PAGE 27
VIVOTEK Video Control Buttons: Depending on the Network Camera model and Network Camera configuration, some buttons may not be available. Snapshot: Click this button to capture and save still images. The captured images will be displayed in a pop-up window. Right-click the image and choose Save Picture As to save it in JPEG (*.jpg) or BMP (*.bmp) format. Digital Zoom: Click and uncheck “Disable digital zoom” to enable the zoom operation.
PAGE 28
VIVOTEK Mute: Turn off the Mic volume on the local computer. The button becomes the after clicking the Mute button. Mic On button Full Screen: Click this button to switch to full screen mode. Press the “Esc” key to switch back to normal mode. ■ The following window is displayed when the video mode is set to MJPEG: Video Title Title and Time Video (HTTP-V) 2015/07/25 17:08:56 Time Video 17:08:56 2015/07/25 Video Control Buttons Video Title: The video title can be configured.
PAGE 29
VIVOTEK Client Settings This chapter explains how to select the stream transmission mode and saving options on the local computer. When completed with the settings on this page, click Save on the page bottom to enable the settings. H.264 Media Options Select to stream video or audio data or both. This is enabled only when the video mode is set to H.264. H.264 Protocol Options H.264 Protocol Options Depending on your network environment, there are four transmission modes of H.
PAGE 30
VIVOTEK Two way audio Half duplex: Audio is transmitted from one direction at a time, e.g., from a PC holding a web console with the camera. Full duplex: Audio is transmitted in both directions simultaneously. MP4 Saving Options Users can record live video as they are watching it by clicking page. Here, you can specify the storage destination and file name. Start MP4 Recording on the main Folder: Specify a storage destination on your PC for the recorded video files. The location can be changed.
PAGE 31
VIVOTEK Joystick settings Enable Joystick Connect a joystick to a USB port on your management computer. Supported by the plug-in (Microsoft’s DirectX), once the plug-in for the web console is loaded, it will automatically detect if there is any joystick on the computer. The joystick should work properly without installing any other driver or software. Then you can begin to configure the joystick settings of connected devices. Please follow the instructions below to enable joystick settings. 1.
PAGE 32
VIVOTEK Buttons Configuration In the Button Configuration window, the left column shows the actions you can assign, and the right column shows the functional buttons and assigned actions. The number of buttons may differ from different joysticks. Please follow the steps below to configure your joystick buttons: 1. Choosing one of the actions and click Assign will pop up a dialog. Then you can assign this action to a button by pressing the joystick button or select it from the drop-down list.
PAGE 33
VIVOTEK Buttons Configuration Click the Configure Buttons button, a window will prompt as shown below. Please follow the steps below to configure your joystick buttons: 1. Select a button number from the Button # pull-down menu. Tips: If you are not sure of the locations of each button, use the Properties window in the Game Controllers utility. 2. Select a corresponding action, such as Patrol or Preset#. 3. Click the Assign button to assign an action to the button.
PAGE 34
VIVOTEK Configuration Click Configuration on the main page to enter the camera setting pages. Note that only Administrators can access the configuration page. VIVOTEK provides an easy-to-use user interface that helps you set up your network camera with minimal effort. In order to simplify the user interface, detailed information will be hidden unless you click on the function item.
PAGE 35
VIVOTEK System > General settings This section explains how to configure the basic settings for the Network Camera, such as the host name and system time. It is composed of the following two columns: System, and System Time. When finished with the settings on this page, click Save at the bottom of the page to enable the settings. System Host name: Enter a desired name for the Network Camera.
PAGE 36
VIVOTEK System time Keep current date and time: Select this option to preserve the current date and time of the Network Camera. The Network Camera’s internal real-time clock maintains the date and time even when the power of the system is turned off. Synchronize with computer time: Select this option to synchronize the date and time of the Network Camera with the local computer. The read-only date and time of the PC is displayed as updated. Manual: The administrator can enter the date and time manually.
PAGE 37
VIVOTEK System > Homepage layout This section explains how to set up your own customized homepage layout. General settings This column shows the settings of your hompage layout. You can manually select the background and font colors in Theme Options (the second tab on this page). The settings will be displayed automatically in this Preview field. The following shows the homepage using the default settings: ■ Hide Powered by VIVOTEK: If you check this item, it will be removed from the homepage.
PAGE 38
VIVOTEK Theme Options Here you can change the color of your homepage layout. There are three types of preset patterns for you to choose from. The new layout will simultaneously appear in the Preview filed. Click Save to enable the settings.
PAGE 39
VIVOTEK ■ Follow the steps below to set up the customed homepage: 1. Click Custom on the left column. 2. Click the field where you want to change the color on the right column. Color Selector Custom Pattern 3. The palette window will pop up as shown below. 2 3 1 4 4. Drag the slider bar and click on the left square to select a desired color. 5. The selected color will be displayed in the corresponding fields and in the Preview column. 6. Click Save to enable the settings.
PAGE 40
VIVOTEK System > Logs This section explains how to configure the Network Camera to send the system log to a remote server as backup. Log server settings Follow the steps below to set up the remote log: 1. Select Enable remote log. 2. In the IP address text box, enter the IP address of the remote server. 2. In the port text box, enter the port number of the remote server. 3. When completed, click Save to enable the setting.
PAGE 41
VIVOTEK You can install the included ST7501 recording software, which provides an Event Management function group for delivering event messages via emails, GSM short messages, onscreen event panel, or to trigger an alarm, etc. For more information, refer to the ST7501 User Manual.
PAGE 42
VIVOTEK Access log Access log displays the access time and IP address of all viewers (including operators and administrators) in a chronological order. The access log is stored in the Network Camera’s buffer area and will be overwritten when reaching a certain limit. System > Parameters The View Parameters page lists the entire system’s parameters. If you need technical assistance, please provide the information listed on this page.
PAGE 43
VIVOTEK System > Maintenance This chapter explains how to restore the Network Camera to factory default, upgrade firmware version, etc. General settings > Upgrade firmware This feature allows you to upgrade the firmware of your Network Camera. It takes a few minutes to complete the process. Note: Do not power off the Network Camera during the upgrade! Follow the steps below to upgrade the firmware: 1. Download the latest firmware file from the VIVOTEK website. The file is in .pkg file format. 2.
PAGE 44
VIVOTEK General settings > Restore This feature allows you to restore the Network Camera to factory default settings. Network: Select this option to retain the Network Type settings (please refer to Network Type on page 70). Daylight Saving Time: Select this option to retain the Daylight Saving Time settings (please refer to Import/Export files below on this page). Custom Language: Select this option to retain the Custom Language settings.
PAGE 45
VIVOTEK 3. Open the file with Microsoft® Notepad and locate your time zone; set the start and end time of DST. When completed, save the file. In the example below, DST begins each year at 2:00 a.m. on the second Sunday in March and ends at 2:00 a.m. on the first Sunday in November. Update daylight saving time rules: Click Browse… and specify the XML file to update. If the incorrect date and time are assigned, you will see the following warning message when uploading the file to the Network Camera.
PAGE 46
VIVOTEK The following message is displayed when attempting to upload an incorrect file format. Export language file: Click to export language strings. VIVOTEK provides nine languages: English, Deutsch, Español, Français, Italiano, 日本語, Português, 簡体中文, and 繁體中文. Update custom language file: Click Browse… and specify your own custom language file to upload. Export configuration file: Click to export all parameters for the device and user-defined scripts.
PAGE 47
VIVOTEK Media > Image This section explains how to configure the image settings of the Network Camera. The Focus window is available only for models that come with motorized lens. General settings Video title Show_timestamp_and video_title_in_video_and_snapshots: Enter a name that will be displayed on the title bar of the live video as the picture shown below. A zoom indicator will be displayed on the Home page when you zoom in/out on the live viewing window as shown below.
PAGE 48
VIVOTEK Video orientation: Flip - vertically reflect the display of the live video; Mirror - horizontally reflect the display of the live video. Select both options if the Network Camera is installed upside-down (e.g., on the ceiling) to correct the image orientation. Please note that if you have preset locations, those locations will be cleared after flip/mirror setting. Rotate - Normal Flip Mirror Rotate 90° clockwise The rotation here indicates clockwise rotation.
PAGE 49
VIVOTEK Smart IR (Smart IR is available when the external/built-in IR option is enabled) When enabled, the camera automatically adjust the IR projection to adjacent objects in order to avoid over-exposure in the night mode. The Smart IR function is more beneficial when the spot of intrusions or an object of your interest is close to the lens and the IR lights. For example, if an intruder has a chance of getting near the range of 3 meters, Smart IR can effectively reduce the over-exposure.
PAGE 50
VIVOTEK Tips: If there is an object in close proximity, the IR lights reflected back from it can mislead the Smart IR’s calculation of light level. To solve this issue, you can place an “Exposure Exclude” window on an unavoidable object in the Exposure setting window. See page 55 for how to do it. You can also configure the “Exposure Exclude” window in a night mode “Profile” setting so that your day time setting is not affected.
PAGE 51
VIVOTEK ■ Schedule mode The Network Camera switches between day mode and night mode based on a specified schedule. Enter the start and end time for day mode. Note that the time format is [hh:mm] and is expressed in 24-hour clock time. By default, the start and end time of day mode are set to 07:00 and 18:00. Light sensor sensitivity Tune the responsiveness of the IR filter to lighting conditions as Low, Normal, or High. When completed with the settings on this page, click Save to enable the settings.
PAGE 52
VIVOTEK Image settings On this page, you can tune the White balance and Image adjustment. Sensor Setting 2: For special situations Sensor Setting 1: For normal situations White balance: Adjust the value for the best color temperature. ■ You may follow the steps below to adjust the white balance to the best color temperature. 1. Place a sheet of paper of white or cooler-color temperature color, such as blue, in front of the lens, then allow the Network Camera to automatically adjust the color temperature.
PAGE 53
VIVOTEK Noise reduction ■ Enable noise reduction: Check to enable noise reduction in order to reduce noises and flickers in image. This applies to the onboard 3D Noise Reduction feature. Use the pull-down menu to adjust the reduction strength. Note that applying this function to the video channel will consume system computing power. 3D Noise Reduction is mostly applied in low-light conditions. When enabled in a low-light condition with fast moving objects, trails of after-images may occur.
PAGE 54
VIVOTEK Exposure On this page, you can set the Exposure measurement window, Exposure level, Exposure mode, Exposure time, Gain control, and Day/Night mode settings. You can configure two sets of Exposure settings: one for normal situations, the other for special situations, such as the day/night/schedule mode. Sensor Setting 2: For special situations Sensor Setting 1: For normal situations Measurement Window: This function allows users to set measurement window(s) for low light compensation.
PAGE 55
VIVOTEK The inclusive window refers to the “weighed window“; the exclusive window refers to “ignored window“. It adopts the weighed averages methodology to calculate the value. The inclusive windows have a higher priority. You can overlap these windows, and, if you place an exclusive window within a larger inclusive window, the exclusive part of the overlapped windows will be deducted from the inclusive window. An exposure value will then be calculated out of the remaining of the inclusive window.
PAGE 56
VIVOTEK Auto: If you set Exposure mode as Auto, the Exposure time and Gain control will not be configurable since the sensor library will automatically adjust the value according to the ambient light. Then you can configure iris mode as “indoor” or “outdoor” to reach the best image quality. ■ Iris mode: Select Indoor or Outdoor iris mode to adapt to the installation. The preset iris aperture setting will apply. Note that on a fixed lens model, this option is not configurable.
PAGE 57
VIVOTEK Focus (For models that come with a motorized lens) Focus here refers to the Remote Focus, and is applicable to Network Cameras that are equipped with stepping motor lens. The automated focus adjustment function eliminates the needs to physically adjust camera focus. In an outdoor deployment consisting of a large number of cameras, the auto focus function can be very helpful when these cameras become out of focus after days or weeks of operation.
PAGE 58
VIVOTEK 5. Wait for the scan to complete. After a short while, the clearest image obtained should be displayed and the optimal focus range achieved. Use the arrow marks on the sides to fine-tune the focus if you are not satisfied with the results. You may still need to use the arrow marks to fine-tune the focus depending on the live image on your screen. “>” means moving from wide to tele end; and “<” tele to wide.
PAGE 59
VIVOTEK Privacy mask Click Privacy Mask to open the settings page. On this page, you can block out sensitive zones to address privacy concerns. ■ To set the privacy mask windows, follow the steps below: 1. Click New to add a new window. 2. You can use 4 mouse clicks to create a new masking window, which is recommended to be at least twice the size of the object (height and width) you want to cover. 3. Enter a Window Name and click Save to enable the setting. 4.
PAGE 60
VIVOTEK Media > Video Mode (Available on 5MP resolution models) You can select different resolutions, 5 megapixel at the max. 15fps and a lower 1080P Full HD resolution at a higher 30fps frame rate, with different aspect ratios, 4:3 or 16:9 for the video streams. Note that changing the FOV will erase your preset points, Motion detection, exposure window, and privacy masks settings.
PAGE 61
VIVOTEK Stream settings This Network Camera supports multiple streams with frame sizes ranging from 176 x 144 to 1920 x 1080 pixels (2MP models). The 5MP model supports a maximum resolution of 2560 x 1920. The definition of multiple streams: ■ Stream 1: Users can define the "Region of Interest" (viewing region) and the "Output Frame Size" (size of the live view window). ■ Stream 2: The default frame size for Stream 2 is set to the 1280 x 720.
PAGE 62
VIVOTEK Please follow the steps below to set up the configurations of a video stream: 1. Select a stream for which you want to set up the viewing region. 2. Select a Region of Interest from the drop-down list. The floating frame, the same as the one in the Gloabl View window on the home page, will resize accordingly. If you want to set up a customized viewing region, you can also resize and drag the floating frame to a desired position with your mouse. 3.
PAGE 63
VIVOTEK Click the stream item to display the detailed information. The maximum frame size will follow your settings in the above Viewing Window sections. This Network Camera offers real-time H.264 and MJPEG compression standards (Dual Codec) for real-time viewing. If the H.264 mode is selected, the video is streamed via RTSP protocol. There are several parameters through which you can adjust the video performance: ■ Frame size You can set up different video resolutions for different viewing devices.
PAGE 64
VIVOTEK If the power line frequency is set to 50Hz, the frame rates are selectable at 1fps, 2fps, 3fps, 5fps, 8fps, 10fps, 15fps, 20fps, and 25fps. If the power line frequency is set to 60Hz, the frame rates are selectable at 1fps, 2fps, 3fps, 5fps, 8fps, 10fps, 15fps, 20fps, 25fps, and 30fps. You can also select Customize and manually enter a value. The frame rate will decrease if you select a higher resolution. ■ Intra frame period Determine how often for firmware to plant an I frame.
PAGE 65
VIVOTEK • Smart stream: Smart stream effectively reduces the quality of the whole or the non-interested areas on a screen and therefore reduces the bandwidth consumed. You can manually specify the video quality for the foreground and the background areas. Select an operation mode if Smart stream is preferred. - Auto tracking: The Auto tracking mode configures the whole screen into the background area.
PAGE 66
VIVOTEK As the result, the lower screen is constantly displayed in high details, while the upper half is transmitted using a lower-quality format. Although the upper half is transmitted using a lower quality format, you still have an awareness of what is happening on the whole screen.
PAGE 67
VIVOTEK If JPEG mode is selected, the Network Camera sends consecutive JPEG images to the client, producing a moving effect similar to a filmstrip. Every single JPEG image transmitted guarantees the same image quality, which in turn comes at the expense of variable bandwidth usage. Because the media contents are a combination of JPEG images, no audio data is transmitted to the client.
PAGE 68
VIVOTEK Media > Audio Audio Settings Mute: Select this option to disable audio transmission from the Network Camera to all clients. Note that if muted, no audio data will be transmitted even if audio transmission is enabled on the Client Settings page. In that case, the following message is displayed: Microphone source: Select to stream the audio from the internal microphone or the external microphone.
PAGE 69
VIVOTEK Network > General settings This section explains how to configure a wired network connection for the Network Camera. Network Type LAN Select this option when the Network Camera is deployed on a local area network (LAN) and is intended to be accessed by local computers. The default setting for the Network Type is LAN. Please rememer to click on the Save button when you complete the Network setting.
PAGE 70
VIVOTEK Primary DNS: The primary domain name server that translates hostnames into IP addresses. Secondary DNS: Secondary domain name server that backups the Primary DNS. Primary WINS server: The primary WINS server that maintains the database of computer names and IP addresses. Secondary WINS server: The secondary WINS server that maintains the database of computer names and IP addresses.
PAGE 71
VIVOTEK NOTE: ► If the default ports are already used by other devices connected to the same router, the Network Camera will select other ports for the Network Camera. ► If UPnP TM is not supported by your router, you will see the following message: Error: Router does not support UPnP port forwarding. ► Steps to enable the UPnP TM user interface on your computer: Note that you must log on to the computer as a system administrator to install the UPnP TM components. 1.
PAGE 72
VIVOTEK 4. In the Networking Services dialog box, select Universal Plug and Play and click OK. 5. Click Next in the following window. 6. Click Finish. UPnP TM is enabled. ► How does UPnP TM work? UPnP TM networking technology provides automatic IP configuration and dynamic discovery of devices added to a network. Services and capabilities offered by networked devices, such as printing and file sharing, are available among each other without the need for cumbersome network configuration.
PAGE 73
VIVOTEK Enable IPv6 Select this option and click Save to enable IPv6 settings. Please note that this only works if your network environment and hardware equipment support IPv6. The browser should be Microsoft® Internet Explorer 8 or 9, Mozilla Firefox 6.0 or above. When IPv6 is enabled, by default, the network camera will listen to router advertisements and be assigned with a link-local IPv6 address accordingly. IPv6 Information: Click this button to obtain the IPv6 information as shown below.
PAGE 74
VIVOTEK Please follow the steps below to link to an IPv6 address: 1. Open your web browser. 2. Enter the link-global or link-local IPv6 address in the address bar of your web browser. 3. The format should be: http://[2001:0c08:2500:0002:0202:d1ff:fe04:65f4]/ IPv6 address 4. Press Enter on the keyboard or click the Refresh button to refresh the webpage.
PAGE 75
VIVOTEK Port HTTPS port: By default, the HTTPS port is set to 443. It can also be assigned to another port number between 1025 and 65535. Two way audio port: By default, the two way audio port is set to 5060. Also, it can also be assigned to another port number between 1025 and 65535. The Network Camera supports two way audio communication so that operators can transmit and receive audio simultaneously.
PAGE 76
VIVOTEK Audio is being transmitted to the Network Camera 2011/03/09 17:08:56 Video (TCP-AV) Talk Button Click Mic Volume Mute to enable audio transmission to the Network Camera; click microphone; click to turn off the audio. To stop talking, click to adjust the volume of again. FTP port: The FTP server allows the user to save recorded video clips. You can utilize VIVOTEK's Installation Wizard 2 to upgrade the firmware via FTP server. By default, the FTP port is set to 21.
PAGE 77
VIVOTEK Network > Streaming protocols HTTP streaming To utilize HTTP authentication, make sure that your have set a password for the Network Camera first; please refer to Security > User account on page 87 for details. Authentication: Depending on your network security requirements, the Network Camera provides two types of security settings for an HTTP transaction: basic and digest.
PAGE 78
VIVOTEK URL command -- http://:/ For example, when the Access name for stream 2 is set to video2.mjpg: 1. Launch Mozilla Firefox or Netscape. 2. Type the above URL command in the address bar. Press Enter. 3. The JPEG images will be displayed in your web browser. http://192.168.5.151/video2.
PAGE 79
VIVOTEK Authentication: Depending on your network security requirements, the Network Camera provides three types of security settings for streaming via RTSP protocol: disable, basic, and digest. If basic authentication is selected, the password is sent in plain text format, but there can be potential risks of it being intercepted. If digest authentication is selected, user credentials are encrypted using MD5 algorithm, thus providing better protection against unauthorized access.
PAGE 80
VIVOTEK Multicast settings for streams: Click the items to display the detailed configuration information. Select the Always multicast option to enable multicast for video streams. Unicast video transmission delivers a stream through point-to-point transmission; multicast, on the other hand, sends a stream to the multicast group address and allows multiple clients to acquire the stream at the same time by requesting a copy from the multicast group address.
PAGE 81
VIVOTEK Network > DDNS This section explains how to configure the dynamic domain name service for the Network Camera. DDNS is a service that allows your Network Camera, especially when assigned with a dynamic IP address, to have a fixed host and domain name. Express link Express Link is a free service provided by VIVOTEK server, which allows users to register a domain name for a network device. One URL can only be mapped to one MAC address.
PAGE 82
VIVOTEK Manual setup DDNS: Dynamic domain name service Enable DDNS: Select this option to enable the DDNS setting. Provider: Select a DDNS provider from the provider drop-down list. VIVOTEK offers Safe100.net, a free dynamic domain name service, to VIVOTEK customers. It is recommended that you register Safe100.net to access VIVOTEK’s Network Cameras from the Internet. Additionally, we offer other DDNS providers, such as Dyndns.org(Dynamic), Dyndns. org(Custom), TZO.com, DHS.
PAGE 83
VIVOTEK [Register] Successfully Your account information has been mailed to registered e-mail address 4. Select Enable DDNS and click Save to enable the setting. ■ CustomSafe100 VIVOTEK offers documents to establish a CustomSafe100 DDNS server for distributors and system integrators. You can use CustomSafe100 to register a dynamic domain name if your distributor or system integrators offer such services. 1. In the DDNS column, select CustomSafe100 from the drop-down list. 2.
PAGE 84
VIVOTEK Network > QoS (Quality of Service) Quality of Service refers to a resource reservation control mechanism, which guarantees a certain quality to different services on the network. Quality of service guarantees are important if the network capacity is insufficient, especially for real-time streaming multimedia applications. Quality can be defined as, for instance, a maintained level of bit rate, low latency, no packet dropping, etc.
PAGE 85
VIVOTEK QoS/DSCP (the DiffServ model) DSCP-ECN defines QoS at Layer 3 (Network Layer). The Differentiated Services (DiffServ) model is based on packet marking and router queuing disciplines. The marking is done by adding a field to the IP header, called the DSCP (Differentiated Services Codepoint). This is a 6-bit field that provides 64 different class IDs. It gives an indication of how a given packet is to be forwarded, known as the Per Hop Behavior (PHB).
PAGE 86
VIVOTEK Network > SNMP (Simple Network Management Protocol) This section explains how to use the SNMP on the network camera. The Simple Network Management Protocol is an application layer protocol that facilitates the exchange of management information between network devices. It helps network administrators to remotely manage network devices and find, solve network problems with ease. ■ The SNMP consists of the following three key components: 1.
PAGE 87
VIVOTEK Security > User accounts This section explains how to enable password protection and create multiple accounts. Root Password The administrator account name is “root”, which is permanent and can not be deleted. If you want to add more accounts in the Manage User column, please apply the password for the “root” account first. 1. Type the password identically in both text boxes, then click Save to enable password protection. 2.
PAGE 88
VIVOTEK Security > HTTPS (Hypertext Transfer Protocol over SSL) This section explains how to enable authentication and encrypted communication over SSL (Secure Socket Layer). It helps protect streaming data transmission over the Internet on higher security level. Create and Install Certificate Method Before using HTTPS for communication with the Network Camera, a Certificate must be created first.
PAGE 89
VIVOTEK 5. Click Save to preserve your configuration, and your current session with the camera will change to the encrypted connection. 6. If your web session does not automatically change to an encrypted HTTPS session, click Home to return to the main page. Change the URL address from “http://” to “https://“ in the address bar and press Enter on your keyboard. Some Security Alert dialogs will pop up. Click OK or Yes to enable HTTPS. https:// https://192.168.5.151/index.
PAGE 90
VIVOTEK Create certificate request and install 1. Select the option from the Method pull-down menu. 2. Click Create certificate to proceed. 3. The following information will show up in a pop-up window after clicking Create. Then click Save to generate the certificate request. 4. The Certificate request window will prompt. If you see the following Information bar, click OK and click on the Information bar at the top of the page to allow pop-ups.
PAGE 91
VIVOTEK 5. Look for a trusted certificate authority, such as Symantec’s VeriSign Authentication Services, that issues digital certificates. Sign in and purchase the SSL certification service. Copy the certificate request from your request prompt and paste it in the CA’s signing request window. Proceed with the rest of the process as CA’s instructions on their webpage. 6. Once completed, your SSL certificate should be delivered to you via an email or other means.
PAGE 92
VIVOTEK 7. Open a new edit, paste the certificate contents, and press ENTER at the end of the contents to add an empty line. 8. Convert file format from DOS to UNIX. Open File menu > Conversions > DOS to Unix.
PAGE 93
VIVOTEK 9. Save the edit using the “.crt” extension, using a file name like “CAcert.crt.” 10. Return to the original firmware session, use the Browse button to locate the crt certificate file, and click Upload to enable the certification.
PAGE 94
VIVOTEK 11. When the certifice file is successfully loaded, its status will be stated as Active. Note that a certificate must have been created and installed before you can click on the “Save" button for the configuration to take effect. 12.To begin an encrypted HTTPS session, click Home to return to the main page. Change the URL address from “http://” to “https://“ in the address bar and press Enter on your keyboard. Some Security Alert dialogs will pop up. Click OK or Yes to enable HTTPS.
PAGE 95
VIVOTEK Security > Access List This section explains how to control access permission by verifying the client PC’s IP address. General Settings Maximum number of concurrent streaming connection(s) limited to: Simultaneous live viewing for 1~10 clients (including stream 1 to stream 3). The default value is 10. If you modify the value and click Save, all current connections will be disconnected and automatically attempt to re-link (IE Explorer or Quick Time Player).
PAGE 96
VIVOTEK ■ Refresh: Click this button to refresh all current connections. ■ Add to deny list: You can select entries from the Connection Status list and add them to the Deny List to deny access. Please note that those checked connections will only be disconnected temporarily and will automatically try to re-link again (IE Explorer or QuickTime Player). If you want to enable the denied list, please check Enable access list filtering and click Save in the first column.
PAGE 97
VIVOTEK There are three types of rules: Single: This rule allows the user to add an IP address to the Allowed/Denied list. For example: 192.168.2.1 Network: This rule allows the user to assign a network address and corresponding subnet mask to the Allow/Deny List. The address and network mask are written in CIDR format. For example: IP address range 192.168.2.x will be bolcked. If IPv6 filter is preferred, you will be prompted by the following window.
PAGE 98
VIVOTEK Security > IEEE 802.1X Enable this function if your network environment uses IEEE 802.1x, which is a port-based network access control. The network devices, intermediary switch/access point/hub, and RADIUS server must support and enable 802.1x settings. The 802.1x standard is designed to enhance the security of local area networks, which provides authentication to network devices (clients) attached to a network port (wired or wireless).
PAGE 99
VIVOTEK 3. When all settings are complete, move the Network Camera to the protected LAN by connecting it to an 802.1x enabled switch. The devices will then start the authentication automatically. NOTE: ► The authentication process for 802.1x: 1. The Certificate Authority (CA) provides the required signed certificates to the Network Camera (the supplicant) and the RADIUS Server (the authentication server). 2. A Network Camera requests access to the protected LAN using 802.
PAGE 100
VIVOTEK PTZ > PTZ settings This section explains how to control the Network Camera’s Pan/Tilt/Zoom operation. Digital: Control the e-PTZ operation. Within a field of view,it allows users to quickly move the focus to a target area for close-up viewing without physically moving the camera. Digital PTZ Operation (E-PTZ Operation) The e-PTZ control settings section will be displayed as shown below: 2015/05/20 09:57:30 x1.8 x1.8 For e-PTZ related details, please refer to page 102.
PAGE 101
VIVOTEK Home page in the E-PTZ Mode x3.3 ■ The e-Preset Positions will also be displayed on the home page. Select one from the drop-down list, and the Network Camera will move to the selected position. ■ If you have set up different preset positions for different streams, you can select one of the video streams to display its separate preset positions.
PAGE 102
VIVOTEK Patrol settings You can select some preset positions for the Network Camera to patrol. Please follow the steps below to set up a patrol schedule: 1. Select the preset locations on the list, and click . 2. The selected preset locations will be displayed on the Patrol locations list. 3. Set the Dwelling time for the preset location during an auto patrol. 4. If you want to delete a preset location from the Patrol locations list, select it and click Remove. 5.
PAGE 103
VIVOTEK NOTE: ► The Preset Positions will also display on the Home page. Select one from the Go to menu, and the Network Camera will move to the selected position. ► Click Patrol: The Network Camera will patrol along the positions repeatedly.
PAGE 104
VIVOTEK Event > Event settings This section explains how to configure the Network Camera to respond to particular situations (event). A typical application is that when a motion is detected, the Network Camera sends buffered images to an FTP server or e-mail address as notifications. Click on Help, there is an illustration shown in the pop-up window explaining that an event can be triggered by many sources, such as motion detection or external devices connected via the digital input wires.
PAGE 105
VIVOTEK ■ Event name: Enter a name for the event setting. ■ Enable this event: Select this option to enable the event setting. ■ Priority: Select the relative importance of this event (High, Normal, or Low). Events with a higher priority setting will be executed first. ■ Detect next event after seconds: Enter the duration in seconds to pause motion detection after a motion is detected. This can prevent event-related actions to take place too frequently. 1.
PAGE 106
VIVOTEK ■ Audio detection A preset threshold can be configured with an external microphone as the trigger to system event. The triggering condition can be an input exceeding or falling below a threshold. Audio detection can take place as a complement to motion detection or as a method to detect activities not covered by the camera's view.
PAGE 107
VIVOTEK Once the triggers are configured, they will be listed under the VADP option. 3. Action Define the actions to be performed by the Network Camera when a trigger is activated. ■ Trigger digital output for seconds Select this option to turn on the external digital output device when a trigger is activated. Specify the length of the trigger interval in the text box. ■ Backup media if the network is disconnected Select this option to backup media file on SD card if the network is disconnected.
PAGE 108
VIVOTEK Add server It is necessary to configure the server and media settings so that the Network Camera will know what action to take (such as which server to send the media files to) when a trigger is activated. Click Add server to open the server setting window. You can specify where the notification messages are sent to when a trigger is activated. A total of 5 server settings can be configured. There are four choices of server types available: Email, FTP, HTTP, and Network storage.
PAGE 109
VIVOTEK To verify if the email settings are correctly configured, click Test. The result will be shown in a pop-up window. If successful, you will also receive an email indicating the result. Click Save server to enable the settings. Note that after you configure the first event server, the new event server will automatically display on the Server list. If you wish to add other server options, click Add server. Server type - FTP Select to send the media files to an FTP server when a trigger is activated.
PAGE 110
VIVOTEK ■ Passive mode Most firewalls do not accept new connections initiated from external requests. If the FTP server supports passive mode, select this option to enable passive mode FTP and allow data transmission to pass through the firewall. The firmware default has the Passive mode checkbox selected. To verify if the FTP settings are correctly configured, click Test. The result will be shown in a pop-up window as shown below. If successful, you will also receive a test.txt file on the FTP server.
PAGE 111
VIVOTEK Network storage: Select to send the media files to a networked storage when a trigger is activated. Please refer to NAS server on page 132 for details. Note that only one NAS server can be configured. Click Save server to enable the settings. ■ SD Test: Click to test your SD card. The system will display a message indicating the result as a success or a failure. If you want to use your SD card for local storage, please format it before use. Please refer to page 113 for detailed information.
PAGE 112
VIVOTEK Click 20150120 to open the directory: The format is: HH (24r) Click to open the file list for that hour 2015/01/20 2015/01/20 Click to go back to the previous level of the directory Click to delete selected items Click to delete all recorded data 2015/01/20 2015/01/20 The format is: File name prefix + Minute (mm) You can set up the file name prefix on Add media page. Please refer to next page for detailed information.
PAGE 113
VIVOTEK Add media Click Add media to open the media setting window. You can specify the type of media that will be sent when a trigger is activated. A total of 5 media settings can be configured. There are three choices of media types available: Snapshot, Video Clip, and System log. Select the item to display the detailed configuration options. You can configure either one or all of them. Media type - Snapshot Select to send snapshots when a trigger is activated.
PAGE 114
VIVOTEK ■ Add date and time suffix to the file name Select this option to add a date/time suffix to the file name. For example: Snapshot_20150513_100341 File name prefix Date and time suffix The format is: YYYYMMDD_HHMMSS Click Save media to enable the settings. Note that after you set up the first media server, a new column for media server will automatically display on the Media list. If you wish to add more media options, click Add media.
PAGE 115
VIVOTEK ■ Maximum file size Specify the maximum file size allowed. Some users may need to stitch the video clips together when searching and packing up forensic evidence. ■ File name prefix Enter the text that will be appended to the front of the file name. For example: Video_20150513_100341 File name prefix Date and time suffix The format is: YYYYMMDD_HHMMSS Click Save media to enable the settings. Media type - System log Select to send a system log when a trigger is activated.
PAGE 116
VIVOTEK In the Event settings column, the Servers and Medias you configured will be listed; please make sure the Event -> Status is indicated as ON, in order to enable the event triggering action. When completed, click the Save event button to enable the settings and click Close to exit Event Settings page. The new Event / Server settings / Media will appear in the event drop-down list on the Event setting page.
PAGE 117
VIVOTEK Customized Script This function allows you to upload a sample script (.xml file) to the webpage, which will save your time on configuring the settings. Please note that there is a limited number of customized scripts you can upload; if the current amount of customized scripts has reached the limit, an alert message will prompt. If you need more information, please contact VIVOTEK technical support.
PAGE 118
VIVOTEK Applications > Motion detection This section explains how to configure the Network Camera to enable motion detection. A total of 5 motion detection windows can be configured. Motion Detection Setting 2: For special situations Motion Detection Setting 1: For normal situations Follow the steps below to enable motion detection: 1. Click New to add a new motion detection window. 2. In the Window Name text box, enter a name for the motion detection window.
PAGE 119
VIVOTEK Photos or videos can be captured instantly and configured to be sent to a remote recepient (via an Email or FTP server). For more information on how to configure an event setting, please refer to Event settings on page 104. A green bar indicates that even though motions have been detected, the event has not been triggered because the image variations still fall under the preset threshold. Larger than the min.
PAGE 120
VIVOTEK This motion detection window will also be displayed on the Event Settings page. You can go to Event > Event settings > Trigger to select it as a trigger source. Please refer to page 130 for detailed information. NOTE: ► How does motion detection work? A C Min. item size Alerted pixels < Min. item size B D Min. item size Alerted pixels > Min. item size There are two motion detection parameters: Sensitivity and Min. Item Size.
PAGE 121
VIVOTEK Applications > DI and DO Digital input: Select High or Low as the Normal status for the digital input. Connect the digital input pin of the Network Camera to an external device to detect the current connection status. Digital output: Select Grounded or Open to define the normal status for the digital output. Connect the digital output pin of the Network Camera to an external device to determine the current status. Set up the event source as DI on Event > Event settings > Trigger.
PAGE 122
VIVOTEK Applications > Tampering detection This section explains how to set up camera tamper detection. With tamper detection, the camera is capable of detecting incidents such as redirection, blocking or defocusing, or even spray paint. Please follow the steps below to set up the camera tamper detection function: 1. Enter the tamper trigger duration. (10 sec. ~ 10 min.
PAGE 123
VIVOTEK Applications > Audio detection Audio detection, along with video motion detection, is applicable in the following scenarios: 1. Detection of activities not covered by camera view, e.g., a loud input by gun shots or breaking a door/window. 2. A usually noisy environment, such as a factory, suddenly becomes quiet due to a breakdown of machines. 3. A PTZ camera can be directed to turn to a preset point by the occurrence of audio events. 4.
PAGE 124
VIVOTEK You can use the Profile window to configure a different Audio detection setting. For example, a place can be noisy in the day time and become very quiet in the night. 1. Click on the Enable this profile checkbox. Once the Audio detection window is opened, the current sound input will be interactively indicated by a fluctuating yellow wave diagram. 2. Use a mouse click to drag the Alarm level tab to a preferred location on the slide bar. 3. Select the Day, Night, or Schedule mode check circles.
PAGE 125
VIVOTEK Applications > PIR Click the checkbox to enable the PIR detection. Default is disabled.
PAGE 126
VIVOTEK Applications > Package management - a.k.a., VADP (VIVOTEK Application Development Platform) Users can store and execute VIVOTEK's or 3rd-party software modules onto the camera's flash memory or SD card. These software modules can apply in video analysis for intelligent video applications such as license plate recognition, object counting, or as an agent for edge recording, etc. • Once the software package is successfully uploaded, the module configuration (vadp. xml) information is displayed.
PAGE 127
VIVOTEK To start a module, select the checkcircle in front, and click the Start button. If you should need to remove a module, select the checkcircle in front and then click the Stop button. By then the module status will become OFF, and the X button will appear at the end of the row. Click on the X button to remove an existing module. When prompted by a confirm message, Click Yes to proceed.
PAGE 128
VIVOTEK On the License page, use the Manual or Automatic to register and activate the license for using VIVOTEK's VADP modules. The Automatic method requires an Internet connection. Without Internet connection, you should acquire the license key elsewhere, and manually upload to the network camera. Follow the onscreen instruction on VIVOTEK's website for the registration procedure. You can proced with the following link to download a license key: http://www.vivotek.com/ vadp_requestactivation.
PAGE 129
VIVOTEK Recording > Recording settings This section explains how to configure the recording settings for the Network Camera. Recording Settings Insert your SD card and click here to test NOTE: ► Please remember to format your SD card via the camera’s web console (in the Local storage . SD card management page) when using it for the first time. Please refer to page 134 for detailed information. Recording Settings Click Add to open the recording setting window.
PAGE 130
VIVOTEK If you enable adaptive recording on a camera, only when an event is triggered on Camera A will the server record the full frame rate streaming data; otherwise, it will only request the I frame data during normal monitoring, thus effectively saves bandwidths and storage space. NOTE: ► To enable adaptive recording, please make sure you’ve set up the trigger source such as Motion Detection, DI Device, or Manual Trigger.
PAGE 131
VIVOTEK 2. Destination You can select the SD card or network storage (NAS) for the recorded video files. If you have not configured a NAS server, see details in the following. NAS server Click Add NAS server to open the server setting window and follow the steps below to set up: 1. Fill in the information for your server. For example: 3 Network storage path (\\server name or IP address\folder name) 1 2 4 User name and password for your server 2. Click Test to check the setting.
PAGE 132
VIVOTEK If successful, you will receive a test.txt file on the network storage server. 3. Enter a server name. 4. Click Save to complete the settings and click Close to exit the page. ■ Capacity: You can choose either the entire free space available or limit the reserved space. The recording size limit must be larger than the reserved amount for cyclic recording. ■ Enable cyclic recording: If you check this item, when the maximum capacity is reached, the oldest file will be overwritten by the latest one.
PAGE 133
VIVOTEK f you want to enable recording notification, please click Event to configure event triggering settings. Please refer to Event > Event settings on page 104 for more details. When completed, select Enable this recording. Click Save to enable the setting and click Close to exit this page. When the system begins recording, it will send the recorded files to the network storage. The new recording name will appear in the drop-down list on the recording page as shown below.
PAGE 134
VIVOTEK Local storage > SD card management NOTE: • • • • • It is recommended to turn OFF the recording activity before you remove an SD card from the camera. The lifespan of an SD card is limited. Regular replacement of the SD card is necessary. Camera filesystem takes up several megabytes of memory space. The storage space taken by filesystem cannot be used for recording. Using an SD card that already contains data recorded by another device should not be used in this camera.
PAGE 135
VIVOTEK SD card control ■ Enable cyclic storage: Check this item if you want to enable cyclic recording. When the maximum capacity is reached, the oldest file will be overwritten by the latest one. ■ Enable automatic disk cleanup: Check this item and enter the number of days you wish to retain a file. For example, if you enter “7 days”, the recorded files will be stored on the SD card for 7 days. Click Save to enable your settings.
PAGE 136
VIVOTEK Search Results The following is an example of search results. There are four columns: Trigger time, Media type, Trigger type, and Locked. Click to sort the search results in either direction. Numbers of entries displayed on one page Click to open a live view ■ Play: Click on a search result which will highlight the selected item. A Play window will appear on top for immediate review of the selected file.
PAGE 137
VIVOTEK ■ Lock/Unlock: Select the checkbox in front of a desired search result, then click this button. The selected items will become Locked, and they will not be deleted during cyclic recording. You can click again to unlock the selections. For example: Click to switch pages ■ Remove: Select the desired search results, then click this button to delete the files.
PAGE 138
VIVOTEK Appendix URL Commands for the Network Camera 1. Overview For some customers who already have their own web site or web control application, the Network Camera/Video Server can be easily integrated through URL syntax. This section specifies the external HTTP-based application programming interface. The HTTP-based camera interface provides the functionality to request a single image, control camera functions (PTZ, output relay etc.), and get and set internal parameter values.
PAGE 139
VIVOTEK 3. General CGI URL Syntax and Parameters CGI parameters are written in lower-case and as one word without any underscores or other separators. When the CGI request includes internal camera parameters, these parameters must be written exactly as they are named in the camera or video server. The CGIs are organized in functionally-related directories under the cgi-bin directory. The file extension .cgi is required. Syntax: http:///cgi-bin/[/...]/.
PAGE 140
VIVOTEK 5. Get Server Parameter Values Note: The access right depends on the URL directory. Method: GET/POST Syntax: http:///cgi-bin/anonymous/getparam.cgi?[] [&…] http:///cgi-bin/viewer/getparam.cgi?[] [&…] http:///cgi-bin/operator/getparam.cgi?[] [&…] http:///cgi-bin/admin/getparam.cgi?[] [&…] Where the should be [_] or [.].
PAGE 141
VIVOTEK http://192.168.0.123/cgi-bin/admin/getparam.cgi?network_ipaddress Response: HTTP/1.0 200 OK\r\n Content-Type: text/html\r\n Context-Length: 33\r\n \r\n network.ipaddress=192.168.0.123\r\n 6. Set Server Parameter Values Note: The access right depends on the URL directory. Method: GET/POST Syntax: http:///cgi-bin/anonymous/setparam.cgi? = [&=…][&update=][&return=] http:///cgi-bin/viewer/setparam.
PAGE 142
VIVOTEK placed at the end of the parameter list Return: HTTP/1.0 200 OK\r\n Content-Type: text/html\r\n Context-Length: \r\n \r\n where is =\r\n [] Only the parameters that you set and are readable will be returned. Example: Set the IP address of server to 192.168.0.123: Request: http://myserver/cgi-bin/admin/setparam.cgi?network_ipaddress=192.168.0.123 Response: HTTP/1.
PAGE 143
VIVOTEK 7. Available parameters on the server Valid values: VALID VALUES DESCRIPTION string[] Text strings shorter than ‘n’ characters. The characters “,’,<,>,& are invalid. string[n~m] Text strings longer than `n’ characters and shorter than `m’ characters. The characters “,’,<,>,& are invalid. password[] The same as string but displays‘*’ instead. Any single integer number in 32-bits. The range is -2147483648~2147483647.
PAGE 144
VIVOTEK W is the pixel number of width. H is the pixel number of height. Ex: 1920x1080, 2048x1536 NOTE: The camera should not be restarted when parameters are changed.
PAGE 145
VIVOTEK 7.1system Group: system NAME VALUE SECURITY DESCRIPTION (get/set) hostname string[64] 1/6 Host name of server (Network Camera, Wireless Network Camera, Video Server, Wireless Video Server). ledoff 6/6 Turn on (0) or turn off (1) all led indicators. date , 6/6 Current date of system. Set to ‘keep’ to keep time datetime keep, date unchanged. Set to ‘auto’ to use NTP to auto synchronize date. , 6/6 Current time of the system.
PAGE 146
VIVOTEK -140: GMT-03:30 Newfoundland -120: GMT-03:00 Brasilia, Buenos Aires, Georgetown, Greenland -80: GMT-02:00 Mid-Atlantic -40: GMT-01:00 Azores, Cape_Verde_IS.
PAGE 147
VIVOTEK Caledonia 480: GMT 12:00 Aucklan, Wellington, Fiji, Kamchatka, Marshall Is. 520: GMT 13:00 Nuku'Alofa daylight_enable 6/6 Enable automaticdaylight saving time in time zone. daylight_dstactualmode 6/7 Check if current time is under daylight saving time. (Used internally) daylight_auto_begintime string[19] 6/7 Display the current daylight saving start time. daylight_auto_endtime string[19] 6/7 Display the current daylight saving end time.
PAGE 148
VIVOTEK user has uploaded. This command can cooperate with other “restoreexceptXYZ” commands. When cooperating with others, the system parameters will be restored to the default value except for a union of the combined results. restoreexceptvadp 0, 7/6 Restore the system parameters to default values except the vadp parameters and VADP modules that stored in the system. This command can cooperate with other “restoreexceptXYZ” commands.
PAGE 149
VIVOTEK format: language_count 0/7 Number of webpage languages available on the server. language_i<0~(count-1)> string[16] 0/7 Available language lists.
PAGE 150
VIVOTEK 7.2status Group: status NAME VALUE SECURITY DESCRIPTION (get/set) di_i<0~(capability_ndi-1)> 1/7 0 => Inactive, normal 1 => Active, triggered (capability.ndi > 0) do_i<0~(capability_ndo-1)> 1/7 0 => Inactive, normal 1 => Active, triggered (capability.ndo > 0) onlinenum_rtsp 0,
PAGE 151
VIVOTEK 7.5security Group: security NAME VALUE SECURITY DESCRIPTION (get/set) privilege_do view, operator, 1/6 admin Indicate which privileges and above can control digital output (capability.ndo > 0) privilege_camctrl view, operator, 1/6 admin Indicate which privileges and above can control PTZ (capability.ptzenabled > 0 or capability.
PAGE 152
VIVOTEK Otherwise, the service may fail. Stopped service will auto-start after changing port settings. Ex: Change HTTP port from 80 to 5556, and change RTP port for video from 5556 to 20480. Then, set preprocess=9 to stop both service first. ”/cgi-bin/admin/setparam.cgi? network_preprocess=9&network_http_port= 5556& network_rtp_videoport=20480” type lan, 6/6 Network connection type. 6/6 1 => Get ipaddress, subnet, router, dns1, pppoe resetip dns2 from DHCP server at next reboot.
PAGE 153
VIVOTEK integer> ca_size 0, certificate_exist 6/6 Certificate installed flag (for TLS) certificate_time 0, certificate_size 0, privatekey_exist 6/6 Private key installed flag (for TLS) privatekey_time 0,
PAGE 154
VIVOTEK 7.6.3 IPV6 Subgroup of network: ipv6 (capability.protocol.ipv6 > 0) NAME VALUE SECURITY DESCRIPTION (get/set) enable 6/6 Enable IPv6. addonipaddress 6/6 IPv6 IP address. addonprefixlen 0~128 6/6 IPv6 prefix length. addonrouter 6/6 IPv6 router address. addondns 6/6 IPv6 DNS address. allowoptional 6/6 Allow manually setup of IP address setting. VALUE SECURITY DESCRIPTION 7.6.
PAGE 155
VIVOTEK 7.6.6 HTTPS port Subgroup of network: https (capability.protocol.https > 0) NAME VALUE SECURITY DESCRIPTION (get/set) port 443, 1025 ~ 65535 1/6 HTTPS port. 7.6.7 RTSP Subgroup of network: rtsp (capability.protocol.rtsp > 0) NAME VALUE SECURITY DESCRIPTION (get/set) port 554, 1025 ~ 65535 1/6 RTSP port. (capability.protocol.rtsp=1) anonymousviewing 1/6 Enable anoymous streaming viewing. authmode disable, 1/6 RTSP authentication mode. basic, (capability.protocol.
PAGE 156
VIVOTEK metadataport 1026~65534 4/4 Multicast metadata port. ttl 1 ~ 255 4/4 Multicasttime to live value. 7.6.8 SIP port Subgroup of network: sip (capability.protocol.sip> 0) NAME VALUE SECURITY DESCRIPTION (get/set) port 1025 ~ 65535 1/6 SIP port. VALUE SECURITY DESCRIPTION 7.6.9 RTP port Subgroup of network: rtp NAME (get/set) videoport 1025 ~ 65535 6/6 Video channel port for RTP. (capability.protocol.rtp_unicast=1) audioport 1025 ~ 65535 6/6 Audio channel port for RTP.
PAGE 157
VIVOTEK type 0, 1 6/6 Ipfilter policy : 0 => allow 1 => deny ipv4list_i<0~9> Single address: Network address: Range address: ipv6list_i<0~9> 7.8Video input Group: videoin NAME (get/set) cmosfreq 50, 60 4/4 CMOS frequency. (capability.videoin.
PAGE 158
VIVOTEK * Only available when "capability_image_c_wbmode" !="-" exposurelevel 0~12 4/4 Exposure level "0,12": This range takes the concept from DC's exposure tuning options. The definition is: 0: EV -2.0 1: EV -1.7 2: EV -1.3 3: EV -1.0 4: EV -0.7 5: EV -0.3 6: EV 0 7: EV +0.3 8: EV +0.7 9: EV +1.0 10: EV +1.3 11: EV +1.7 12: EV +2.0 irismode fixed, indoor, 4/4 Control DC-Iris mode.
PAGE 159
VIVOTEK (capability.videoin.c.
PAGE 160
VIVOTEK * Available value is listed in * This parameter may also restrict image "capability_image_c frame rate from sensor due to sensor _exposure_ma generates a frame per exposure time. Ex: If xrange" this is set to 1/5s ~ 1/8000s and camera takes 1/5s on the night, then sensor only outputs 5 frame/s.
PAGE 161
VIVOTEK module. Then, act as rbgain mode "widerange": Auto Tracing White balance (2000K to 10000K). "outdoor": auto white balance mode specifically for outdoor. "indoor": auto white balance mode specifically for indoor. "sodiumauto": sodium vapor lamps. * Only available when "capability_image_c_wbmode" != "-" rgain 0~100 4/4 Manual set rgain value of gain control setting. 0: Weak <-> 100: Strong * Only available when "rbgain" is listed in "capability_image_c_wbmode".
PAGE 162
VIVOTEK 6: EV 0 7: EV +0.3 8: EV +0.7 9: EV +1.0 10: EV +1.3 11: EV +1.7 12: EV +2.0 exposuremode auto, 4/4 Select exposure mode. irispriority, "auto": Iris, Gain and Shutter manual, Speed(Exposure time) can be set etc automatically. "shutterpriority": Adjust with (Available options are list in variable Shutter Speed, auto Iris and "capability_image_c_exposure_m Gain. odetype") "irispriority": Adjust with variable Iris, auto Gain and Shutter speed.
PAGE 163
VIVOTEK "manual": Manual set P-Iris by "piris_position". "-": not support. (only available when "capability_image_c<0~(n-1)>_sens ortype" is "smartsensor") * Only available when "capability_image_c_iristype"=pi ris piris_position 1~100 1/4
PAGE 164
VIVOTEK 0: Low <-> 100: High * Only available when "capability_image_c_agc_mingai n" != "-" * Only valid when "piris_mode"=manual or "irismode"=fixed * Normalized range. * Only available when "capability_image_c_exposure_ra ngetype" is "twovalues". gainvalue 0~100 4/4 Gain value. 0: Low <-> 100: High * Only available when "capability_image_c_agc_maxgai n" != "-" and "capability_image_c_exposure_ra ngetype" is "onevalue". * Normalized range.
PAGE 165
VIVOTEK Bit 3 => Support tilt operation; 0(not support), 1(support) Bit 4 => Support zoom operation; 0(not support), 1(support) Bit 5 => Support focus operation; 0(not support), 1(support)(SD/PZ/IZ series only) text string[64] 1/4 Enclose caption. imprinttimesta 4/4 Overlay time stamp on video. top, bottom 4/4 Text on video string position 20~40 4/4 Text on video font size textonvideo_fon /usr/share/font/Default.ttf, 4/4 Choose camera default font file tpath /mnt/flash2/upload.
PAGE 166
VIVOTEK etc. 5~8000 => 1/5s ~ 1/8000s etc. * Available value is listed in "capability_image_c_exposure_m * This parameter may also restrict axrange" image frame rate from sensor due to sensor generates a frame per exposure time. Ex: If this is set to 1/5s ~ 1/8000s and camera takes 1/5s on the night, then sensor only outputs 5 frame/s.
PAGE 167
VIVOTEK * We support this parameter when the version number (httpversion) is equal or greater than 0302a. enablepreview 1/4 Usage for UI of exposure settings. Preview settings of video profile. crop_position 1/7 Crop left-top corner coordinate. 1/7 Crop width and height. (x,y) crop_size (WxH) (width must be 16x or 32x and height must be 8x) zoomratiodispla 1/4 y Indicates multiple of zoom in is “on-screen display” or not.
PAGE 168
VIVOTEK valid when "capability_smartstream_support"=1 and "capability_smartstream_version" is not equal "2.0") s<0~(m-1)>_h 1~5, 264_quant 99, 100 4/4 Set the pre-defined quality level: 1: Medium 2: Standard 3: Good 4: Detailed 5: Excellent 100: Use the quality level in "qpercent" 99: Use the quality level in "qvalue" * Only valid when "ratecontrolmode"= vbr. s<0~(m-1)>_h 0~51 4/4 Manual video 264_qvalue quality level input. The Q value which is used by encoded library directly.
PAGE 169
VIVOTEK When the bit rate exceeds this value, ate frames will be dropped to restrict the bit rate. * Only valid when "ratecontrolmode"= vbr s<0~(m-1)>_h 1~5, 100 4/4 264_cbr_quant Set the pre-defined quality level: 1: Medium 2: Standard 3: Good 4: Detailed 5: Excellent 100: Use the quality level in "cbr_qpercent" * Only available when "ratecontrolm ode"= cbr. * Only available when "capability_s martstream_v ersion"=2.
PAGE 170
VIVOTEK cbr s<0~(m-1)>_h framerate,imagequality 4/4 Set prioritypolicy 264_prioritypoli * Only valid when "ratecontrolmode"= cy cbr s<0~(m-1)>_h 1~"capability_videoin_c_h264_m 264_maxframe axframerate" 1/4 The maximum frame rates of a H264 stream at different resolutions("capability_videoin_c0_re solution ") are recorded in "capability_videoin_c_h264_maxf ramerate" s<0~(m-1)>_h 0~2 1/4 264_profile Indicate H264 profiles 0: baseline 1: main profile 2: high profile s 4/4 E
PAGE 171
VIVOTEK i o d _ e n a b l e s<0~(m-1)>_h 250, 500, 1000, 2000, 3000, 4000 4/4 265_intraperiod The time interval between two I-frames (Intra coded picture). The unit is millisecond (ms). * Only available when h265 is listed in "capability_videoin_codec". s<0~(m-1)>_h cbr, vbr, smart 4/4 cbr: Constant bit rate mode. 265_ratecontrol vbr: Fixed quality mode, all frames are mode encoded in the same quality. smart: Smart stream mode.
PAGE 172
VIVOTEK "capability_videoin_codec" and "ratecontrolmode"= vbr. s<0~(m-1)>_h 0~51 4/4 Manual video 265_qvalue quality level input. The Q value which is used by encoded library directly. * Only available when h265 is listed in "capability_videoin_codec". * Only valid when "ratecontrolmode"= vbr and s<0~(m-1)>_h265_quant = 99. s<0~(m-1)>_h 1~100 4/4 265_qpercent Select customized quality in a normalized full range.
PAGE 173
VIVOTEK quality level: 1: Medium 2: Standard 3: Good 4: Detailed 5: Excellent 100: Use the quality level in "cbr_qpercent" * Only available when h265 is listed in "capability_videoin_codec" and "ratecontrolmode"= cbr. * Only available when "capability_smartstream_version"=2. 0 s<0~(m-1)>_h 1~100 4/4 Select customized quality in a 265_cbr_qperce normalized full range. nt 1: Worst quality 100: Best quality * Only available when h265 is listed in "capability_videoin_codec".
PAGE 174
VIVOTEK s<0~(m-1)>_h 1~"capability_videoin_c_h265_m 265_maxframe axframerate" 1/4 The maximum frame rates of a H265 stream at different resolutions("capability_videoin_c0_re solution ") are recorded in "capability_videoin_c_h265_maxf ramerate" * Only available when h265 is listed in "capability_videoin_codec". s<0~(m-1)>_h 0~2 1/4 265_profile Indicate H265 profiles 0: baseline 1: main profile 2: high profile * Only available when h265 is listed in "capability_videoin_codec".
PAGE 175
VIVOTEK ex: 0301a_2) s<0~(m-1)>_m 1~100 4/4 jpeg_qpercent Select customized quality in a normalized full range. 1: Worst quality 100: Best quality * Only valid when "ratecontrolmode"= vbr and s<0~(m-1)>_mjpeg_quant = 100. s<0~(m-1)>_m 20000~"capability_videoin_c_mj jpeg_maxvbrbit peg_maxbitrate" 4/4 The maximum allowed bit rate in fixed quality mode. rate When the bit rate exceeds this value, frames will be dropped to restrict the bit rate.
PAGE 176
VIVOTEK "capability_smartstream_version"=2. 0 s<0~(m-1)>_m 20000~"capability_videoin_c_mj jpeg_bitrate peg_maxbitrate" 4/4 The target bit rate in constant bit rate mode.
PAGE 177
VIVOTEK dependent> 1: on * Only available when "capability_image_c_aespeed" is 1 aespeed_speedl 1~100 4/4 The speed level of AE converge speed. evel 1~20: level 1 41~60: level 3 61~80: level 4 81~100: level 5 Level 1~4(low ~ high) The higher speed level meas shorter AE converged time during AE executing. * Only available when "capability_image_c_aespeed" is 1 aespeed_sensiti 1~100 4/4 The sensitivity of AE converge speed.
PAGE 178
VIVOTEK * Only available when "capability_fisheye" > 0 enablewatermar 0, 1 1/6 k 0: Not to add watermarks on images 1: Add watermarks on images * Only available when "capability_fisheye" > 0 s<0~(m-2)>_fi ‘1O, 1P, 2P, 1R, 4R’ for ceiling/floor 1/4 sheyedewarpmo mount “1O” is original mode (disable). de ‘1O, 1P, 1R, 4R’ for wall mount Supported dewarp mode is different by mount type. dependent> Local dewarp mode.
PAGE 179
VIVOTEK Group: videoin_c<0~(n-1)>_s<0~(m-1)>_h265_smartstream_win_i<0~(k-1)> (capability_smartstream_support=1 and h265 is listed in "capability_videoin_codec" and capability_smartstream_mode_manual = 1) n denotes the value of "capability_nvideoin",m denotes the value of " capability_nmediastream",k denotes the value of "capability_smartstream_nwindow_manual". NAME VALUE SECURITY DESCRIPTION (get/set) enable 4/4 Enable or disable the window.
PAGE 180
VIVOTEK range" * Only valid when "piris_mode"=manual or "irismode"=fixed * Only available when "capability_image_c_exposure_rangetyp e" is "twovalues". maxexposure <1~32000>, 4/4 Maximum exposure time <5~32000>, 1~32000 => 1s ~ 1/32000s <1~8000>, 5~32000 => 1/5s ~ 1/32000s <5~8000>, 1~8000 => 1s ~ 1/8000s etc. 5~8000 => 1/5s ~ 1/8000s etc.
PAGE 181
VIVOTEK * Only available when "capability_image_c_exposure_maxrang e" != "-" and "capability_image_c_exposure_rangetyp e" is "onevalue". * We support this parameter when the version number (httpversion) is equal or greater than 0302a. enableblc 4/4 Enable backlight compensation. * Not support this parameter anymore when the version number (httpversion) is equal or greater than 0301a. * It's recommanded to use "exposurewin_c_mode" to switch on/off BLC.
PAGE 182
VIVOTEK are list in "irispriority": Adjust with variable Iris, auto "capability_image_c Gain and Shutter speed. _exposure_mo "manual": Adjust with variable Shutter, Iris detype") and Gain. * We support this parameter when the version number (httpversion) is equal or greater than 0302a. whitebalance auto, 4/4 manual, "auto": Auto white balance rbgain, "rbgain": Use rgain and bgain to set white widerange, balance manually.
PAGE 183
VIVOTEK * Only available when "rbgain" is listed in "capability_image_c_wbmode". * Only valid when "videoin_c_whitebalance" != auto * Normalized range. maxgain 0~100 4/4 Maximum gain value. 0: Low <-> 100: High * Only available when "capability_image_c_agc_maxgain" != "-" * Only valid when "piris_mode"=manual or "irismode"=fixed * Normalized range. * Only available when "capability_image_c_exposure_rangetyp e" is "twovalues". mingain 0~100 4/4 Minimum gain value.
PAGE 184
VIVOTEK piris_mode manual, indoor, outdoor,- 1/4 Control P-Iris mode. "outdoor": Auto-setting P-Iris to get best quality, but easy to meet rolling or flicker effect in indoor environment. "indoor": Avoid rolling and flicker effect first. "manual": Manual set P-Iris by "piris_position".
PAGE 185
VIVOTEK "capability_image_c_wdrc_mode" is 1 wdrc_strength 1~100 4/4 The strength of WDR enhanced. The bigger value means the stronger strength of WDR enhanced. * Only available when "capability_image_c_wdrc_mode" is 1 aespeed_mode 4/4 Turning AE converge speed on or off. 0: off 1: on * Only available when "capability_image_c_aespeed" is 1 aespeed_speedlevel 1~100 4/4 The speed level of AE converge speed.
PAGE 186
VIVOTEK 7.9Time Shift settings Group: timeshift for n channel profucts and m stream n denotes the value of "capability_nvideoin", m denotes the value of "capability_nmediastream" (capability.timeshift > 0) NAME VALUE SECURITY DESCRIPTION (get/set) enable 4/4 Enable time shift streaming. c<0~(n-1)>_s<0~(m-1) 4/4 Enable time shift streaming for specific >_allow stream. 7.10 IR cut control Group: ircutcontrol (capability.
PAGE 187
VIVOTEK (if capability_daynight There are two value format: _c_ircutsensitiv "low,normal,high": if ity_type=options) capability_daynight_c_ircutsensitivity_ty pe=options 1~100 (if capability_daynight "1~100": if _c_ircutsensitiv capability_daynight_c_ircutsensitivity_ty ity_type=normalize pe=normalize ) 7.
PAGE 188
VIVOTEK 100: Use " image_c_saturationpercent" * Only available when bit 2 of "capability_image_c_basicsetting" is 1. * We replace "saturation" with "saturationpercent". * This parameter will not be used after the version number (httpversion) is equal or greater than 0400a. sharpness -3~3,100 4/4 -3: Softer <-> 3: Sharper 100: Use " image_c_sharpnesspercent" * Only available when bit 3 of "capability_image_c_basicsetting" is 1.
PAGE 189
VIVOTEK "capability_image_c_basicsetting" is 1 gammacurve 0~100 4/4 0: Fine-turned gamma curve by Vivotek. 1: Gamma value = 0.01 2: Gamma value = 0.02 3: Gamma value = 0.03 ... 100: Gamma value = 1 * Note: Although we set gamma value to 100 level, but not all gamma values are valid. Internal module will take the closest valid one. For example, 1~45 may all be mapped to gamma value = 0.45, etc. lowlightmode 4/4 Enable/disable low light mode.
PAGE 190
VIVOTEK dis_mode 4/4 Digital image stabilizer 0:disable 1:enable * Only available when 'dis' is listed in "capability_image_c_is_mode". dis_strength 1~100 4/4 Strength of digital image stabilizer * Only available when 'dis' is listed in "capability_image_c_is_mode".
PAGE 191
VIVOTEK "capability_image_c_basicsetting" is 1 * We replace "profile_i0_brightness" with "profile_i0_brightnesspercent". * This parameter will not be used after the version number (httpversion) is equal or greater than 0400a. profile_i<0~(m-1)>_contrast -5~5,100 4/4 -5: Less contrast <-> 5: More contrast 100: Use " image_c_contrastpercent" * Only available when bit 1 of "capability_image_c_basicsetting" is 1.
PAGE 192
VIVOTEK profile_i<0~(m-1)>_brightness 0~100 4/4 percent Set brightness in the normalized range. 0: Darker <-> 100: Bright * Only available when bit 0 of "capability_image_c_basicsetting" is 1. profile_i<0~(m-1)>_contrastpe 0~100 4/4 rcent Set contrast in the normalized range. 0: Less contrast <-> 100: More contrast * Only available when bit 1 of "capability_image_c_basicsetting" is 1 profile_i<0~(m-1)>_saturation 0~100 4/4 percent Set saturation in the normalized range.
PAGE 193
VIVOTEK profile_i<0~(m-1)>_dnr_stren 1~100 4/4 Strength of 3DNR gth * Only available when "capability_image_c_dnr" is 1 profile_i<0~(m-1)>_defog_mo 4/4 Enable/disable defog mode.
PAGE 194
VIVOTEK lpcparkinglot, "capability_image_c_scenemode_support lpcstreet " is 1 "capability_image_c_scenemode_support type" 7.
PAGE 195
VIVOTEK homepx <0~W,0~H> 4/4 Left-top corner coordinate of the window. W: 0~ The current image width -1 * Only available when px is listed in H: 0~ The current image height -1 "capability_image_c_exposure_windomai n". sizepx <0~Wx0~ H> 4/4 Width and height of the window. W: 0~ The current image width -1 * Only available when px is listed in H: 0~ The current image height -1 "capability_image_c_exposure_windomai n".
PAGE 196
VIVOTEK (Only valid when exposurewin_c_mode=custom) NAME VALUE SECURITY DESCRIPTION (get/set) enable 4/4 Enable or disable the window. policy 0~1 4/4 0: Indicate exclusive. 1: Indicate inclusive. * Only available when exclusive is listed in "capability_image_c_exposure_wintype". home <0~320,0~240> 4/4 Left-top corner coordinate of the window. * Only available when qvga is listed in "capability_image_c_exposure_windomai n".
PAGE 197
VIVOTEK 7.13 Audio input per channel Group: audioin_c<0~(n-1)> for n channel products (capability.naudioin>0) n denotes the value of "capability_nvideoin" NAME VALUE SECURITY DESCRIPTION (get/set) source micin, linein dependent> 4/4 micin => use built-in microphone input. linein => use external microphone input. * Reserved for compatibility, and suggest don't use this since the version number (httpversion) is equal or greater than 0301a.
PAGE 198
VIVOTEK "capability_audio_extmic" is equal to 1). mute 0, 1 1/4 0: Mute off 1: Mute on gain 0~100 4/4 _source = linein) this> * Reserved for compatibility, and suggest don't use this since the version number (httpversion) is equal or greater than 0301a. * We replace "gain" with "volume_internal" and "volume_external". More details, please refer the parameter description of "volume_internal" and "volume_external".
PAGE 199
VIVOTEK 5900, * Only available if AMR is supported. 6700, 7400, 7950, 10200, 12200 s0_g711_mode pcmu, 4/4 pcma Set G.711 companding algorithm. pcmu: µ-law algorithm pcma: A-law algorithm * Only available if G.711 is supported. s0_g726_bitrate 16000, 4/4 Set G.726 encoded bitrate in bps. 24000, * Only available if G.726 is supported. 32000, 40000 s0_g726_bitstreampackin little, big 4/4 gmode Set G.726 bit streaming packing mode. little: Little-endian bitstream format.
PAGE 200
VIVOTEK 7.14 Motion detection settings Group: motion_c<0~(n-1)> for n channel products n denotes the value of "capability_nvideoin" NAME VALUE SECURITY DESCRIPTION (get/set) enable 4/4 Enable motion detection. win_sensitivity 1 ~ 100 4/4 Sensitivity of all motion detection windows. Group: motion_c<0~(n-1)>_win_i<0~(k-1)> n denotes the value of "capability_nvideoin", k denotes the value of "capability_nmotion".
PAGE 201
VIVOTEK * It's recommended to use polygonsd * This parameter will not be used after the version number (httpversion) is equal or greater than 0400a. polygon 0 ~ 320,0 ~ 240, 0 4/4 Coordinate of polygon window position. 320,0 ~ 240, 0 ~ * Only available when 320,0 ~ 240 "capability_motion_wintype" = polygon.
PAGE 202
VIVOTEK this> "capability_motion_wintype" = rectangle. * Only available when qvga is listed in "capability_motion_windomain". * It's recommended to use polygonsd * This parameter will not be used after the version number (httpversion) is equal or greater than 0400a. height 0 ~ 240 4/4 Height of motion detection window. "capability_motion_wintype" = rectangle. * Only available when qvga is listed in "capability_motion_windomain".
PAGE 203
VIVOTEK NAME VALUE SECURITY DESCRIPTION (get/set) enable 4/4 Enable motion detection window. name string[14] 4/4 Name of motion window. polygonstd 0 ~ 9999,0 ~ 9999, 4/4 Coordinate of polygon window position. 0 ~ 9999,0 ~ 9999, (4 points: x0,y0,x1,y1,x2,y2,x3,y3) 0 ~ 9999,0 ~ 9999, * Only available when 0 ~ 9999,0 ~ 9999 "capability_motion_wintype" = polygon.
PAGE 204
VIVOTEK * It's recommended to use polygonsd * This parameter will not be used after the version number (httpversion) is equal or greater than 0400a. left 0 ~ 320 4/4 Left coordinate of window position. "capability_motion_wintype" = rectangle. * Only available when qvga is listed in "capability_motion_windomain".
PAGE 205
VIVOTEK * Only available when qvga is listed in "capability_motion_windomain". * It's recommended to use polygonsd * This parameter will not be used after the version number (httpversion) is equal or greater than 0400a. 7.15 Tampering detection settings Group: tampering_c<0~(n-1)> for n channel products (capability.tampering > 0) n denotes the value of "capability_nvideoin" NAME VALUE SECURITY DESCRIPTION (get/set) enable 4/4 Enable or disable tamper detection.
PAGE 206
VIVOTEK triggered. 7.16 DDNS Group: ddns (capability.protocol.ddns > 0) NAME VALUE SECURITY DESCRIPTION (get/set) enable 6/6 Enable or disable the dynamic DNS. provider CustomSafe100, 6/6 Safe100 => safe100.net DyndnsDynamic, DyndnsDynamic => dyndns.org (dynamic) DyndnsCustom, DyndnsCustom => dyndns.org Safe100 CustomSafe100 => Custom server using safe100 method _hostname string[128] 6/6 Your DDNS hostname.
PAGE 207
VIVOTEK 7.18 UPnP presentation Group: upnppresentation NAME VALUE SECURITY DESCRIPTION (get/set) enable 6/6 Enable or disable the UPnP presentation service. 7.19 UPnP port forwarding Group: upnpportforwarding NAME VALUE SECURITY DESCRIPTION (get/set) enable 6/6 Enable or disable the UPnP port forwarding service. upnpnatstatus 0~3 6/7 The status of UPnP port forwarding, used internally. 0 = OK, 1 = FAIL, 2 = no IGD router, 3 = no need for port forwarding 7.
PAGE 208
VIVOTEK 0: disable 1: Show log of parameter setting set from external. 2. Show log of parameter setting set from external and internal. 7.21 SNMP Group: snmp (capability.protocol.snmp > 0) NAME VALUE SECURITY DESCRIPTION (get/set) v2 6/6 SNMP v2 enabled. 0 for disable, 1 for enable v3 6/6 SNMP v3 enabled.
PAGE 209
VIVOTEK 7.22 Layout configuration Group: layout NAME VALUE SECURITY DESCRIPTION (get/set) logo_default 1/6 0 => Custom logo 1 => Default logo logo_link string[128] 1/6 Hyperlink of the logo 1/6 0 => display the power by vivotek logo http://www.vivotek.
PAGE 210
VIVOTEK 7.23 Privacy mask Group: privacymask_c<0~(n-1)> for n channel products and m privacy mask window. n denotes the value of "capability_nvideoin" and m denotes the value of "capability_videoin_c<0~(n-1)>_nprivacymask" NAME VALUE SECURITY DESCRIPTION (get/set) enable 4/4 Enable privacy mask. win_i<0~(m-1)>_enable 4/4 Enable privacy mask window. win_i<0~(m-1)>_name string[14] 4/4 Name of the privacy mask window.
PAGE 211
VIVOTEK ~ W,0 ~ H "capability_image_c_privacymask_wintype" W: 0~ The = polygon. current image width -1 * Only available when px is listed in H: 0~ The "capability_image_c_privacymask_windomai current image n height -1 win_i<0~(m-1)>_polygonstd 0 ~ 9999,0 ~ 4/4 Coordinate of polygon window position. 9999, 0 ~ (4 points: x0,y0,x1,y1,x2,y2,x3,y3) 9999,0 ~ * Only available when 9999, 0 ~ "capability_image_c_privacymask_wintype" 9999,0 ~ = polygon.
PAGE 212
VIVOTEK 7.25 Capability Group: capability NAME VALUE SECURITY DESCRIPTION (get/set) api_httpversion 0/7 The version of VIVOTEK WebAPI with 4 This number start integers plus 1 alphabet, There are composed with 0301a. by "major version", "minor version", "revision","_platform". ex: 0301a_1 Major version Increase the major version when change, remove the old features/interfaces or the firmware has substantially change in architecture and not able to roll back to previous version.
PAGE 213
VIVOTEK document. The 5th character is model-based version for API bug-fix and it's default to "a". Ex: If some APIs in a model does not follow the API definition of 0301a_1, we will fix them and change this API value to 0301b_1. bootuptime 0/7 Server bootup time. nir 0, 0/7 Number of IR interfaces.
PAGE 214
VIVOTEK More details, please refer the parameter description of "volume_internal" and "volume_external". nuart 0, 0/7 Number of UART interfaces. nmotion 0/7 The number of motion window. nmotionprofile 0,
PAGE 215
VIVOTEK it means that the camera supports remotefocus function. bit 0 => Indicate whether to support both zoom and focus function. bit 1 => Only support zoom function. bit 2 => Only support focus function. bit 3 => Currently, this is a reserved bit, and the default value is 0. * It's strongly non-recommended to use this. * This is kept for compatibility.
PAGE 216
VIVOTEK 2nd bit of the group indicates 2nd stream of a channel support ePTZ or not, and so on. * For most products, the last stream of a channel will not support ePTZ. It is reserved for full view of the channel. For some dual-stream products, both streams support ePTZ. nanystream 0, iva analysis whitelight 0/7 Indicate whether to support white light led.
PAGE 217
VIVOTEK "pir" = PIR detection "visignal" = Video input signal loss. "backup" = Backing up recorded files * Only available when [httpversion] >= 0301a storage_dbenabled 0/7 Media files are indexed in database. protocol_https < boolean > 0/7 Indicate whether to support HTTP over SSL. protocol_rtsp < boolean > 0/7 Indicate whether to support RTSP. protocol_sip 0/7 Indicate whether to support SIP.
PAGE 218
VIVOTEK * This is kept for compatibility. videoin_maxframerate A list of 0/7 This equals "capability_videoin_c0_maxframerate". * This is kept for compatibility. videoin_mjpeg_maxframe A list of rate and "-" 0/7 This equals "capability_videoin_c0_mjpeg_maxframerate ". * This is kept for compatibility. videoin_h264_maxframer A list of ate and "-" 0/7 This equals "capability_videoin_c0_h264_maxframerate".
PAGE 219
VIVOTEK "nvideoout"=1 with NTSC, "videoout_codec"=ntsc "nvideoout"=1 with PAL, "videoout_codec"=pal "nvideoout"=2 with both NTSC, "videoout_codec"=ntsc,ntsc * For camera, this feature is controlled by physical jump on device. No WebAPI to control it. This value is set only on camera power-on and maintains the status. * Only available when [httpversion] >= 0301a timeshift 0/7 Indicate whether to support time shift caching stream.
PAGE 220
VIVOTEK audio_extmic. audio_lineout 0/7 Indicate whether to support line output. audio_michardwareswitch 0/7 Indicate whether the hardware supports built-in/external mic switch audio_headphoneout 0/7 Indicate whether to support headphone output. * Not support this parameter anymore when the version number (httpversion) is equal or greater than 0301a. audioin_codec aac4, gamr, g711, 0/7 g726, - Available audio codec.
PAGE 221
VIVOTEK std: A normalized 0~9999 range. -: Not supported. *only available when "capability_smartstream_support" is 1 smartstream_mode_autot 0/7 racking Indicate whether autotracking smart stream is supported. *only available when "capability_smartstream_support" is 1 smartstream_mode_man 0/7 ual Indicate whether manual smart stream is supported.
PAGE 222
VIVOTEK vadp_supportfeature 0/7 An 32-bit integer, each bit can be set separately as follows: Bit 0 => VADP interface Bit 1 => Capture video raw data Bit 2 => Support encode jpeg Bit 3 => Capture audio raw data Bit 4 => Support event trigger Bit 5 => Support license registration Bit 6 => Support shared memory API Bit 7 => Support digital signature of package Bit 8 => Support snapshot vadp_npackage 0/7 Indicate the maximum number of VADP package that can be upload
PAGE 223
VIVOTEK 0: support only /cgi-bin/viewer/camctrl.cgi uart_httptunnel 0/7 Indicate whether to support HTTP tunnel for UART transfer. transmission_mode Tx, 0/7 Rx, Indicate transmission mode of the machine: TX = server, Rx = receiver box, Both = DVR. Both network_wire 0/7 Indicate whether to support Ethernet. network_wireless 0/7 Indicate whether to support wireless. wireless_s802dot11b 0/7 Indicate whether to support wireless 802.11b+.
PAGE 224
VIVOTEK media_videoclip_maxpree 0/7 vent image_iristype Maximum duration (second) after event occurred in a videoclip. 0/7 Indicate iris type.  "dciris": DC-Iris  "-": No Iris control support * When "capability_iris"=0, this value must be "-". * Note: For some box-type cameras, this value may be varied depending on mounted lens. * We replace "capability_image_iristype" with " capability_image_c0_iristype ".
PAGE 225
VIVOTEK localstorage_slconnum 0, 0/7 The maximum seamless connection number. localstorage_smartsd 0/7 The "Lifetime and Log SD Card" feature allows users to obtain the card's remaining lifetime information. 0: Non-support this feature 1: Support this feature * Only Sony SD card can support this function now.
PAGE 226
VIVOTEK ircutsensitivity_type 0/7 Indicate the cgi interface of "ircutcontrol_sensitivity". "options": the value of "ircutcontrol_sensitivity" parameter is "low, normal,high". "normalize": the value of "ircutcontrol_sensitivity" parameter is "1~100" * Only available when "capability_daynight_c_support" is 1. * We support this parameter when the version number (httpversion) is equal or greater than 0302a.
PAGE 227
VIVOTEK streamcodec 0/7 Represent supported codec types of each stream. This contains a list of positive integers, split by comma. Each one stands for a stream, and the definition is as following: Bit 0: Support MPEG4. Bit 1: Support MJPEG Bit 2: Support H.264 Bit 3: Support H.265 mode 0, 0/7 Indicate current video mode. nmode 0/7 Indicate how many video modes supported by this channel.
PAGE 228
VIVOTEK mjpeg_maxframerate A list of and "-" Maximum fps that the device can encoded with MJPEG on resolutions in current video mode. "-" means not support. * One to one mapping to the resolution in "resolution". * The element number is defined as "nresolution" in this group. * This parameter may be changed when "videoin_c_cmosfreq"=50 or "videoin_c_modulation"=pal. Ex: 30 fps is changed to 25 fps, 60 fps is changed to 50 fps, and so on.
PAGE 229
VIVOTEK h264_maxbitrate 0/7 Maximum bitrates of H.264. The unit is bps. * Only available when 'h264' is listed in "capability_videoin_codec". h265_maxframerate A list of and "-" Maximum fps that the device can encoded with H.265 on resolutions in current video mode. "-" means not support. * One to one mapping to the resolution in "resolution". * The element number is defined as "nresolution" in this group.
PAGE 230
VIVOTEK cameraunit_name CU8131, 0/7 A "camera unit" name of a split-type camera CU8171, system, which the camera unit and the video CU8161-H, core are separated. CU8162-H, -: If the camera is not a split-type camera CU8163-H, system, the value of this parameter is "-". CU8361-H, ..., * We support this parameter when the version - number (httpversion) is equal or greater than < 0302b.
PAGE 231
VIVOTEK resolutionC2P A list of 0/7 Available resolutions of 2P mode of ceiling and floor mount. resolutionC1R A list of 0/7 Available resolutions of 1R mode of ceiling and floor mount. resolutionC4R A list of 0/7 Available resolutions of 4R mode of ceiling and floor mount. resolutionW1P A list of 0/7 Available resolutions of 1P mode of wall mount. resolutionW1R A list of 0/7 Available resolutions of 1R mode of wall mount.
PAGE 232
VIVOTEK binning 0, 1, 3 0/7 Indicate binning is used or not in this video mode. 0: No binning 1: 2x2 binning 3: 3x3 binning * Binning is a technology to increase light sensitivity by combining multiple pixels to one. The drawback is reduced resolution. We design this parameter to disclose this information. nresolution 0/7 How many resolution options in this video mode. resolution A list of 0/7 Resolution options in this video mode.
PAGE 233
VIVOTEK maxfps_mjpeg A list of and "-" Maximum fps which the device can encoded with MJPEG on resolutions in this video mode. "-" means not support. * One to one mapping to the resolution in "resolution". * The element number is defined as "nresolution" in this group. * This parameter records the frame rate when "videoin_c_cmosfreq"=60 or "videoin_c_modulation"=ntsc * Only available when 'mjpeg' is listed in "capability_videoin_codec".
PAGE 234
VIVOTEK Group: capability_videoin_c<0~(n-1)>_mode<0~(m-1)>_defaultsetting_s<0~(j-1)> n denotes the value of "capability_nvideoin", m denotes the value of "capability_videoin_c_nmode", j denotes the value of "capability_nmediastream" PARAMETER VALUE SECURITY DESCRIPTION (get/set) resolution A list of 0/7 Default setting of resolution options. "-" means not support. * The element number is defined as "capability_nresolution".
PAGE 235
VIVOTEK "capability_nresolution". h265_bitrate A list of and "-" this video mode. "-" means not support. * The element number is defined as "capability_nresolution". Group: capability_image_c<0~(n-1)> n denotes the value of "capability_nvideoin" NAME VALUE SECURITY DESCRIPTION (get/set) basicsetting 0, 0/7 A 32-bits integer, each bit can be set separately as follows: Bit 0 => Supports Brightness or not.
PAGE 236
VIVOTEK exposurewin.mode.blc:disab value. The affected functions are list led:, here. aespeed:disabled:, exposurelevel:hidden:, The format is "Affect API exposurelevel:fixed:, name":"Policy":"Value" exposurelevel:ranged:, "Policy" can be categorized into exposuremode:fixed:auto following groups: - (disabled) : UI turns grey and users : nonnegative integer can't select it. - (unchanged) : UI keeps the status as before and user can't change it.
PAGE 237
VIVOTEK WDR Enhanced. wdrc_affect -, 0/7 When WDR Pro or WDR Enhanced is exposurewin.mode:fixed:au enabled, some features may become to, malfunction or be forced to a given exposurewin.mode.blc:disab value. The affected functions are list led:, here.
PAGE 238
VIVOTEK eis 0,1 0/7 0: Non-support electronic image stabilizer 1: Support electronic image stabilizer is_mode eis, 0/7 Indicate the image stabilizer mode. dis, "eis": electronic image stabilizer - "dis": digital image stabilizer "-": not support * We support this parameter when the version number (httpversion) is equal or greater than 0302a. is_strength 0/7 0: Non-support tuning strength of image stabilizer mode. 1: Support tuning strength of image stabilizer mode.
PAGE 239
VIVOTEK "Policy" can be categorized into following groups: - (disabled) : UI turns grey and users can't select it. - (unchanged) : UI keeps the status as before and user can't change it. - (hidden) : UI is hidden. - (fixed) : UI is fixed to one selection or value. - (ranged) : UI is fixed to multiple selections or values. "Affect API name" can be described in hierarchy, such as "exposurewin.mode.blc:disabled:" which means blc exposure window is disabled.
PAGE 240
VIVOTEK scenemode_visibility_affe -, 0/7 When scene mode is enabled, some ct minexposure:hidden:, features may become malfunction or mingain:hidden:, be forced to a given value. The wdrpro:unchanged:, affected functions are list here. 3dnr:unchanged:, or others The format is "Affect API name":"Policy":"Value" : nonnegative integer "Policy" can be categorized into following groups: - (disabled) : UI turns grey and users can't select it.
PAGE 241
VIVOTEK ect minexposure:hidden:, features may become malfunction or mingain:hidden:, be forced to a given value. The wdrpro:unchanged:, affected functions are list here. 3dnr:unchanged:, or others The format is "Affect API name":"Policy":"Value" : nonnegative integer "Policy" can be categorized into following groups: - (disabled) : UI turns grey and users can't select it. - (unchanged) : UI keeps the status as before and user can't change it.
PAGE 242
VIVOTEK mingain:hidden:, be forced to a given value. The wdrpro:unchanged:, affected functions are list here. 3dnr:unchanged:, or others The format is "Affect API name":"Policy":"Value" : nonnegative integer "Policy" can be categorized into following groups: - (disabled) : UI turns grey and users can't select it. - (unchanged) : UI keeps the status as before and user can't change it. - (hidden) : UI is hidden.
PAGE 243
VIVOTEK wdrpro:unchanged:, affected functions are list here. 3dnr:unchanged:,or others The format is "Affect API : nonnegative integer name":"Policy":"Value" "Policy" can be categorized into following groups: - (disabled) : UI turns grey and users can't select it. - (unchanged) : UI keeps the status as before and user can't change it. - (hidden) : UI is hidden. - (fixed) : UI is fixed to one selection or value. - (ranged) : UI is fixed to multiple selections or values.
PAGE 244
VIVOTEK outdoor,indoor, sodiumauto, iristype piris, 0/7 Indicate iris type. dciris, "piris": P-Iris - "dciris": DC-Iris "-": No Iris control support * Note: For some cameras, this value may be varied depending on mounted lens. sensortype rawsensor, 0/7 Indicate sensor type. "rawsensor": Raw sensor smartsensor "smartsensor": Smart sensor * We support this parameter when the version number (httpversion) is equal or greater than 0302a.
PAGE 245
VIVOTEK be up to the assigned value (videoin_c_shuttervalue). "-": not support. * Only available when "capability_image_c_exposure_ra ngetype" is "onevalue". * We support this parameter when the version number (httpversion) is equal or greater than 0302a. exposure_gainvaluetype fixed, 0/7 * One to one mapping to the mode maximum, type in "exposure_modetype". - "fixed": The shutter value is the assigned value (videoin_c_gainvalue).
PAGE 246
VIVOTEK before and user can't change it. - (hidden) : UI is hidden. - (fixed) : UI is fixed to one selection or value. - (ranged) : UI is fixed to multiple selections or values. "Affect API name" can be described in hierarchy, such as "exposurewin.mode.blc:disabled:" which means blc exposure window is disabled. API name can be one word as well, such as "exposurelevel:fixed:6" which means exposurelevel is fixed to level 6. "Value" can be a nonnegative integer or NULL. "-" means no feature is affected.
PAGE 247
VIVOTEK - (disabled) : UI turns grey and users can't select it. - (unchanged) : UI keeps the status as before and user can't change it. - (hidden) : UI is hidden. - (fixed) : UI is fixed to one selection or value. - (ranged) : UI is fixed to multiple selections or values. "Affect API name" can be described in hierarchy, such as "exposurewin.mode.blc:disabled:" which means blc exposure window is disabled.
PAGE 248
VIVOTEK : nonnegative integer "Policy" can be categorized into following groups: - (disabled) : UI turns grey and users can't select it. - (unchanged) : UI keeps the status as before and user can't change it. - (hidden) : UI is hidden. - (fixed) : UI is fixed to one selection or value. - (ranged) : UI is fixed to multiple selections or values. "Affect API name" can be described in hierarchy, such as "exposurewin.mode.blc:disabled:" which means blc exposure window is disabled.
PAGE 249
VIVOTEK exposurelevel:hidden:, or others The format is "Affect API name":"Policy":"Value" : nonnegative integer "Policy" can be categorized into following groups: - (disabled) : UI turns grey and users can't select it. - (unchanged) : UI keeps the status as before and user can't change it. - (hidden) : UI is hidden. - (fixed) : UI is fixed to one selection or value. - (ranged) : UI is fixed to multiple selections or values.
PAGE 250
VIVOTEK * When "exposure_mode"=0, this must be set to "-". exposure_winmode auto, 0/7 custom, Available options for "exposurewin_c_mode" blc, - * "-" means group: exposurewin is not supported. * When exposure_mode="0", this must be set to "-". exposure_wintype inclusive, 0/7 The supported exposure window type. exclusive, inclusive: The image inside a window is - the target area of exposure control. exclusive: The image inside a window is omitted by exposure control.
PAGE 251
VIVOTEK -, "1,32000" => 1s ~ 1/32000s or others "1,8000" => 1s ~ 1/8000s etc. "-" means maximum exposure time is not available. * When "exposure_mode"=0, this must be set to "-". exposure_minrange "1,32000", 0/7 Available range for "1,8000", "videoin_c_minexposure" -, "1,32000" => 1s ~ 1/32000s or others "1,8000" => 1s ~ 1/8000s etc. "-" means minimum exposure time is not available. * When "exposure_mode"=0, this must be set to "-".
PAGE 252
VIVOTEK "-" "videoin_c_mingain" “0,100” => 0~100 percent "-" means "videoin_c_mingain" is not available. flickerless 0,1 0/7 0: Non-support flickerless 1: Support flickerless flickerlessaffect -, 0/7 When flickerless is enabled, some minexposure:hidden:, features may become malfunction or mingain:hidden:, be forced to a given value. The or others affected functions are list here.
PAGE 253
VIVOTEK * When "flickerless" = 0, this must be "-" defog_mode 0,1 0/7 0: Non-support defog 1: Support defog defog_strength 0, 1 0/7 0: Non-support tuning strength of defog 1: Support tuning strength of defog * If "capability_image_c_defog_mode "=1, this may be either 0 or 1. defog_supportlevel 0, 0/7 The value indicate the support strength level of defog.
PAGE 254
VIVOTEK well, such as "exposurelevel:fixed:6" which means exposurelevel is fixed to level 6. "Value" can be a nonnegative integer or NULL. "-" means no feature is affected. * When "defog" = 0, this must be "-" aespeed 0,1 0/7 0: Non-support AE speed 1: Support AE speed aespeedsupportlevel 0/7 The value indicate the support strength level of aespeed. * Only available when "capability_image_c_aespeed" is 1.
PAGE 255
VIVOTEK * We support this parameter when the version number (httpversion) is equal or greater than 0302a. autotrack_support 0/7 0: Non-support auto tracking feature 1: Support auto tracking feature * We support this parameter when the version number (httpversion) is equal or greater than 0302a.
PAGE 256
VIVOTEK 7.26 Customized event script Group: event_customtaskfile_i<0~2> PARAMETER VALUE SECURITY DESCRIPTION (get/set) name string[40] 6/6 Custom script identification of this entry. date string[4~20] 6/6 Date of custom script. time string[4~20] 6/6 Time of custom script. 7.27 Event setting Group: event_i<0~2> PARAMETER VALUE SECURITY DESCRIPTION (get/set) name string[40] 6/6 Identification of this entry. enable 0, 1 6/6 Enable or disable this event.
PAGE 257
VIVOTEK di 0, 6/6 Indicate the source id of di trigger. This field is required when trigger condition is “di”. One bit represents one digital input. The LSB indicates DI 0. mdwin 0, 6/6 Indicate the source window id of motion detection. This field is required when trigger condition is “md”. One bit represents one window. The LSB indicates the 1st window. For example, to detect the 1st and 3rd windows, set mdwin as 5.
PAGE 258
VIVOTEK weekday 0~127 6/6 Indicate which weekday is scheduled. One bit represents one weekday. bit0 (LSB) = Saturday bit1 = Friday bit2 = Thursday bit3 = Wednesday bit4 = Tuesday bit5 = Monday bit6 = Sunday For example, to detect events on Friday and Sunday, set weekday as 66. begintime hh:mm 6/6 Begin time of the weekly schedule. endtime hh:mm 6/6 End time of the weekly schedule.
PAGE 259
VIVOTEK action_goto_name string[40] 6/6 Specify the preset name that ptz goto on event triggered. * Only available when capability_ptzenabled > 0. 7.
PAGE 260
VIVOTEK ns_username string[64] 6/6 Username to log in to the server. ns_passwd string[64] 6/6 Password of the user. ns_workgroup string[64] 6/6 Workgroup for network storage. 7.29 Media setting for event action Group: media_i<0~4> PARAMETER VALUE SECURITY DESCRIPTION (get/set) name string[40] 6/6 Identification of this entry type snapshot, 6/6 Media type to send to the server or systemlog, store on the server.
PAGE 261
VIVOTEK videoclip_prefix string[16] 6/6 Indicate the prefix of the filename. videoclip_preevent 0~" 6/6 Indicates the time for pre-event capability_media_videoclip_maxpre recording in seconds. event" videoclip_maxduration 1~" 6/6 capability_media_videoclip_maxlen Maximum duration of one video clip in seconds. gth" videoclip_maxsize 50 ~ " 6/6 capability_media_videoclip_maxsiz Maximum size of one video clip file in Kbytes. e" 7.
PAGE 262
VIVOTEK maxretentiontime 6/6 To specify the expired time for automatic clean up, and it only takes effect for video clip generated by recording_i <0~1>. Format is “‘P[Y]Y[MM]M[DDD]DT[hh]H[mm]M[ss]S’ , similar with ISO8601 with symbols P Ex. P7D, it means 7 days. P1DT10H, it means 1 days and 10 hours. The parameter takes effect when autocleanup_ maxretentiontime_recording_enabled is enabled.
PAGE 263
VIVOTEK weekday 0~127 6/6 Indicate which weekday is scheduled. One bit represents one weekday. bit0 (LSB) = Saturday bit1 = Friday bit2 = Thursday bit3 = Wednesday bit4 = Tuesday bit5 = Monday bit6 = Sunday For example, to detect events on Friday and Sunday, set weekday as 66. begintime hh:mm 6/6 Start time of the weekly schedule. endtime hh:mm 6/6 End time of the weekly schedule. (00:00~24:00 indicates schedule always on) prefix string[16] 6/6 Indicate the prefix of the filename.
PAGE 264
VIVOTEK 7.31 HTTPS Group: https (capability.protocol.https > 0) NAME VALUE SECURITY DESCRIPTION (get/set) enable 6/6 To enable or disable secure HTTP. policy 6/6 If the value is 1, it will force HTTP connection redirect to HTTPS connection method auto, 6/6 auto =>Create self-signed certificate manual, automatically. install manual =>Create self-signed certificate manually. install =>Create certificate request and install.
PAGE 265
VIVOTEK 7.32 Storage management setting Group: disk_i<0~(n-1)> n is the total number of storage devices. (capability.storage.dbenabled > 0) Currently it’s only for local storage (SD, CF card), so n is equal to 1. PARAMETER VALUE SECURITY DESCRIPTION (get/set) cyclic_enabled 6/6 Enable cyclic storage method. autocleanup_enabled 6/6 Enable automatic clean up method. deleted.
PAGE 266
VIVOTEK maxretentiontime_recordin 6/6 g_i <0~1>_maxage To specify the expired time for automatic clean up, and it only takes effect for video clip generated by recording_i <0~1>. Format is “‘P[Y]Y[MM]M[DDD]DT[hh]H[mm]M[ss]S’ , similar with ISO8601 with symbols P Ex. P7D, it means 7 days. P1DT10H, it means 1 days and 10 hours. The parameter takes effect when autocleanup_ maxretentiontime_recording_enabled is enabled.
PAGE 267
VIVOTEK 7.33 Region of interest Group: roi_c<0~(n-1)> for n channel product. (capability.eptz > 0) m denotes the value of "capability_nmediastream". PARAMETER VALUE SECURITY DESCRIPTION (get/set) s<0~(m-2)>_home 1/6 ROI left-top corner coordinate.* If the minimal window size is 64x64, then the "win_i0_home"=(0~resolution_W-64, 0~resolution_H-64), which the resolution is the value in current stream. s<0~(m-2)>_size 1/6 ROI width and height.
PAGE 268
VIVOTEK tiltspeed -5 ~ 5 1/7 Tilt speed (It should be set by eCamCtrl.cgi rather than by setparam.cgi.) panspeed -5 ~ 5 1/7 Pan speed (It should be set by eCamCtrl.cgi rather than by setparam.cgi.) zoomspeed -5 ~ 5 1/7 Zoom speed (It should be set by eCamCtrl.cgi rather than by setparam.cgi.) autospeed 1~5 1/7 Auto pan/patrol speed (It should be set by eCamCtrl.cgi rather than by setparam.cgi.
PAGE 269
VIVOTEK 7.35 Focus Window setting Group: focuswindow_c<0~(n-1)> for n channel products n denotes the value of "capability_nvideoin". (capability_image_c<0~(n-1)>_backfocus=1 or capability_image_c<0~(n-1)>_remotefocus=1) PARAMETER VALUE SECURITY DESCRIPTION (get/set) win_i0_enable 4/4 Enable or disable the window. win_i0_home 4/4 Left-top corner coordinate of the window.
PAGE 270
VIVOTEK 7.37 VIVOTEK Application Development Platformsetting Group: vadp NAME VALUE SECURITY DESCRIPTION (get/set) version 6/7 Indicate the VADP version. resource_total_memory 0, 6/7 Indicate total available memory size for VADP modules. resource_total_storage 0, 6/7 Indicate total size of the internal storage space for storing VADP modules. resource_free_memory 0, 6/7 Indicate free memory size for VADP modules.
PAGE 271
VIVOTEK vendorurl string[120] 6/6 URL of the vendor. version string[40] 6/6 Version of the module. license string[40] 6/6 Indicate the license status of the module. licmsg string[128] 6/6 Indicate the message that will be show on license status when mouse over. path string[40] 6/6 Record the storage path of the module. initscr string[40] 6/6 The script that will handle operation commands from the system. status string[40] 6/6 Indicate the running status of the module.
PAGE 272
VIVOTEK 7.38 camera PTZ control Group: camctrl (capability.camctrl.ptztunnel > 0) NAME VALUE SECURITY DESCRIPTION (get/set) enableptztunnel 1/4 Enable PTZ tunnel for camera control. Group: camctrl_c<0~(n-1)> for n channel products (capability.
PAGE 273
VIVOTEK 7.39 camera PTZ control (SD series) Group: camctrl (the bit7 of capability_ptzenabled is 0 and the bit4 of capability_ptzenable is 1) k denotes the value of "capability_npreset" NAME VALUE SECURITY DESCRIPTION (get/set) ccdtype string[16] 6/7 (Internal used, read only) motortype string[16] 6/7 (Internal used, read only) cameraid 1 ~ 255 1/4 Camera ID controlling external PTZ camera. Note: Please set your speed dome to the appropriate baud rate, and Camera ID, e.g.
PAGE 274
VIVOTEK The dwelling time of each patrol location disablemdonptz 1/4 Disable motion detection on PTZ operation. defaulthome 1/4 This field tells system to use default home position or not. axisx capability_ptz_minpan ~ 1/4 Custom home pan position. 1/4 Custom home tilt position. 1/4 Custom home zoom position. 1/4 Custom home focus position.
PAGE 275
VIVOTEK tour_i<0~19>_checklist string[512] 1/4 The indexes of preset positions, separated by “,” tour_i<0~19>_dwelltime string[512] 1/4 Preset tour: time to wait before moving to the next preset position, separated by “,” Recorded tour: number of seconds to wait before continuing a loop tour. 7.40 UART control Group: uart (capability.nuart > 0 and capability.fisheye = 0) NAME VALUE SECURITY DESCRIPTION (get/set) ptzdrivers_i<0~19, string[40] 1/4 Name of the PTZ driver.
PAGE 276
VIVOTEK speedlink_i<0~4>_name string[40] 1/4 Additional PTZ command name. speedlink_i<0~4>_cmd string[40] 1/4 Additional PTZ command list. ptzdriver 0~19, 1/4 The PTZ driver is used by this COM port. 127 (custom), 128 (no driver) 7.41 UART control (SD series) Group: uart (capability.nuart > 0 and the bit7 of capability_ptzenabled is 0, the bit4 of capability_ptzenable is 1) NAME VALUE SECURITY DESCRIPTION (get/set) cameraid 1~255 4/4 Camera ID controlling external PTZ camera.
PAGE 277
VIVOTEK 7.42 Lens configuration Group: lens for n channel products n denotes the value of "capability_nvideoin" (capability.image.c<0~(n-1)>.lensconfiguration.support = 1) NAME VALUE SECURITY DESCRIPTION (get/set) selected 6/7 Current selected lens profile. e.g. lens_selected=lens_default_i0, it means choosen lens configuration is i0 lens of default group.
PAGE 278
VIVOTEK 7.43 Fisheye info Group: fisheyeinfo (capability.fisheye > 0) NAME VALUE SECURITY DESCRIPTION (get/set) revisedcenteraxis 6/7 The actual center axis coordinate radius 0, 7.
PAGE 279
VIVOTEK 7.46 Auto tracking setting Group: autotrack (capbility_image_c<0~(capability_nvideoin)-1>_autotrack_support > 0) PARAMETER VALUE SECURITY DESCRIPTION (get/set) objsize_type -1~2 1/4 Type of object size. -1 : customized width and height 0 : object size = 30 x 30 1 : object size = 10 x 20 2 : object size = 10 x 10 objsize_customized_width 10~320 1/4 The minimum width of tracking target. objsize_customized_height 10~240 1/4 The minimum height of tracking target.
PAGE 280
VIVOTEK 8. Useful Functions 8.1 Drive the Digital Output (capability.ndo > 0) Note: This request requires Viewer privileges. Method: GET/POST Syntax: http:///cgi-bin/dido/setdo.cgi?do1=[&do2=] [&do3=][&do4=] Where state is 0 or 1; “0” means inactive or normal state, while “1” means active or triggered state.
PAGE 281
VIVOTEK Example: Query the status of digital input 1 . Request: http://myserver/cgi-bin/dido/getdi.cgi?di1 Response: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: 7\r\n \r\n di1=1\r\n 8.3 Query Status of the Digital Output (capability.ndo > 0) Note: This request requires Viewer privileges Method: GET/POST Syntax: http:///cgi-bin/dido/getdo.cgi?[do0][&do1][&do2][&do3] If no parameter is specified, all the digital output statuses will be returned. Return: HTTP/1.
PAGE 282
VIVOTEK \r\n do1=1\r\n 8.4 Capture Single Snapshot Note: This request requires Normal User privileges. Method: GET/POST Syntax: http:///cgi-bin/viewer/video.jpg?[channel=][&resolution=] [&quality=][&streamid=] If the user requests a size larger than all stream settings on the server, this request will fail. PARAMETER VALUE DEFA DESCRIPTION ULT channel 0~(n-1) 0 The channel number of the video source. resolution IP8165: 0 The resolution of the image.
PAGE 283
VIVOTEK 8.5 Account Management Note: This request requires Administrator privileges. Method: GET/POST Syntax: http:///cgi-bin/admin/editaccount.cgi? method=&username=[&userpass=][&privilege=] [&privilege=][…][&return=] PARAMETER VALUE DESCRIPTION method Add Add an account to the server. When using this method, the“username” field is necessary. It will use the default value of other fields if not specified.
PAGE 284
VIVOTEK 8.6 System Logs Note: This request require Administrator privileges. Method: GET/POST Syntax: http:///cgi-bin/admin/syslog.cgi Server will return the most up-to-date system log. Return: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: \r\n \r\n \r\n 8.7 Upgrade Firmware Note: This request requires Administrator privileges. Method: POST Syntax: http:///cgi-bin/admin/upgrade.
PAGE 285
VIVOTEK 8.8 ePTZ Camera Control (capability.eptz > 0 and capability_fisheye = 0) Note: This request requires camctrl privileges. Method: GET/POST Syntax: http:///cgi-bin/camctrl/eCamCtrl.
PAGE 286
VIVOTEK http://IPAddr/cgi-bin/camctrl/eCamCtrl.cgi?stream=0&zooming=wide&zs=5 zooming is used to indicate the moving direction, and zs is used to indicate the speed. To stop a continuous movement, you have to use the command as below: http://IPAddr/cgi-bin/camctrl/eCamCtrl.cgi?stream=0&zoom=stop&zs=0 2.
PAGE 287
VIVOTEK vx The direction of movement, used for joystick control. vy vs 0~7 Set the speed of movement, “0” means stop. x x-coordinate clicked by user. It will be the x-coordinate of center after movement. y y-coordinate clicked by user. It will be the y-coordinate of center after movement. videosize The size of plug-in (ActiveX)window in web page resolution The resolution of streaming.
PAGE 288
VIVOTEK recall Text string less than 40 One of the present positions to recall. characters return Redirect to the page after the parameter is assigned. The can be a full URL path or relative path according to the current path. 8.10 ePTZ Preset Locations(capability.eptz > 0 and capability_fisheye = 0) Note: This request requires Operator privileges. Method: GET/POST Syntax: http:///cgi-bin/operator/ePreset.
PAGE 289
VIVOTEK 8.11 IP Filtering Note: This request requires Administrator access privileges. Method: GET/POST Syntax: http:///cgi-bin/admin/ipfilter.cgi?type[=] http:///cgi-bin/admin/ipfilter.cgi?method=add&ip=[&index=][&ret urn=] http:///cgi-bin/admin/ipfilter.
PAGE 290
VIVOTEK method ip addv4 Add IPv4 address into access list. addv6 Add IPv6 address into access list. delv4 Delete IPv4 address from access list. delv6 Delete IPv6 address from access list. Single address: Network address: Range address: index The start position to add or to delete. return Redirect to the page after the parameter is assigned.
PAGE 291
VIVOTEK This channel will help to transfer the raw data of UART over the network. Please see UART tunnel spec for detail information PARAMETER VALUE DESCRIPTION channel 0 ~ (n-1) The channel number of UART. 8.14 Event/Control HTTP Tunnel Channel (capability. evctrlchannel > 0) Note: This request requires Administrator privileges. Method: GET and POST Syntax: http:///cgi-bin/admin/ctrlevent.
PAGE 292
VIVOTEK 8.15 Get SDP of Streams Note: This request requires Viewer access privileges. Method: GET/POST Syntax: http:///_accessname> “m” is the stream number. “network_accessname_<0~(m-1)>” is the accessname for stream “1” to stream “m”. Please refer to the “subgroup of network: rtsp” for setting the accessname of SDP. You can get the SDP by HTTP GET. When using scalable multicast, Get SDP file which contains the multicast information via HTTP. 8.
PAGE 293
VIVOTEK 8.17 Senddata (capability.nuart > 0) Note: This request requires Viewer privileges. Method: GET/POST Syntax: http:///cgi-bin/viewer/senddata.cgi? [com=][&data=][&flush=] [&wait=] [&read=] PARAMETER VALUE DESCRIPTION com 1 ~ data is a series of digits from 0 ~ 9, A ~ F. Each data>[,
PAGE 294
VIVOTEK 8.18 Storage managements (capability.storage.dbenabled > 0) Note: This request requires administrator privileges. Method: GET and POST Syntax: http:///cgi-bin/admin/lsctrl.cgi?cmd=[&=…] The commands usage and their input arguments are as follows. PARAMETER VALUE DESCRIPTION cmd_type Required. Command to be executed, including search, insert, delete, update, and queryStatus.
PAGE 295
VIVOTEK Indicate if the file is locked or not. 0: file is not locked. 1: file is locked. A locked file would not be removed from UI or cyclic storage. triggerTime Optional. Indicate the event trigger time. (not the file created time) Format is “YYYY-MM-DD HH:MM:SS” Please embrace your input value with single quotes. Ex. triggerTime=’2008-01-01 00:00:00’ If you want to search for a time period, please apply “TO” operation. Ex.
PAGE 296
VIVOTEK Command: update PARAMETER VALUE DESCRIPTION label Required. Identify the designated record. Ex. label=1 isLocked Required. Indicate if the file is locked or not. Ex. Update records whose key numbers are 1 and 5 to be locked status. http:///cgi-bin/admin/lsctrl.cgi?cmd=update&isLocked=1&label=1&label=5 Ex. Update records whose key numbers are 2 and 3 to be unlocked status. http:///cgi-bin/admin/lsctrl.
PAGE 297
VIVOTEK 8.19 Virtual input (capability.nvi > 0) Note: Change virtual input (manual trigger) status. Method: GET Syntax: http:///cgi-bin/admin/setvi.cgi?vi0=[&vi1=][&vi2=] [&return=] PARAMETER VALUE DESCRIPTION vi state[(duration)nstate] Ex: vi0=1 Setting virtual input 0 to trigger state Where "state" is 0, 1.
PAGE 298
VIVOTEK 8.20 Open Timeshift Stream (capability.timeshift > 0, timeshift_enable=1, timeshift_c_s_allow=1) Note: This request requires Viewer access privileges. Syntax: For HTTP push server (MJPEG): http:///_accessname>?maxsft=[&tsmode=&reftime=&forcechk&minsft=] For RTSP (MP4 and H264), the user needs to input theURL below into an RTSP compatible player.
PAGE 299
VIVOTEK Return Code Description 400 Bad Request Request is rejected because some parameter values are illegal. 415 Unsupported Media Type Returned, if forcechk appears,when minsft is not achievable or the timeshift feature of the target stream is not enabled. 8.21 Remote Focus Note: This request requires Administrator privileges. Method: GET/POST Syntax: http:///cgi-bin/admin/remotefocus.
PAGE 300
VIVOTEK position 0~ Motor’s position. It works only if function=zoom | focus and direction=direct. is refer to remote_focus_focus_motor_max which replied from "function=getstatus" steps 1 ~ Motor’s moving steps. It works only if function= focus and direction=forward | backward. is refer to remote_focus_focus_motor_max which replied from "function=getstatus" iris N/A Open iris or not. It works only if function=auto | scan. 8.
PAGE 301
VIVOTEK 8.23 Upload Files Note: This request requires Administrator privileges. Method: POST Syntax: For daylight saving time configuration file: http:///cgi-bin/admin/upload_dst.cgi Post data: filename =\r\n \r\n For language file: http:///cgi-bin/admin/upload_lan.cgi Post data: filename =\r\n \r\n For setting backup file: http:///cgi-bin/admin/upload_backup.
PAGE 302
VIVOTEK 8.24 Update Lens Configuration Note: This request requires Administrator privileges. Method: GET Syntax: For list all names of lens installed in camera: http:///cgi-bin/admin/update_lens.cgi?list_lens For choose selected lens configuration: http:///cgi-bin/admin/update_lens.cgi?choose_lens= For delete selected lens configuration: http:///cgi-bin/admin/update_lens.cgi?delete_lens= PARAMETER value VALUE DESCRIPTION Available lens name.
PAGE 303
VIVOTEK 8.25 Media on demand (capability.localstorage.modnum > 0) Media on demand allows users to select and receive/watch/listen to metadata/video/audio contents on demand. Note: This request requires Viewer access privileges. Syntax: rtsp:///mod.sdp?[&stime=][&etime=][&length =][&loctime =][&file=][&tsmode=] PARAMETER VALUE DEFAULT stime N/A Start time. etime N/A End time.
PAGE 304
VIVOTEK 8.26 Fisheye local dewarp camera control (capability.fisheye > 0 and capability.fisheyelocaldewarp.c0 > 0, only support in 1R mode) Note: This request requires camctrl privileges. Method: GET/POST Syntax: http:///cgi-bin/camctrl/fdCamCtrl.
PAGE 305
VIVOTEK zoom wide Zoom larger view with current speed. tele Zoom further with current speed. speedpan -5 ~ 5 Set the pan speed of current command. speedtilt -5 ~ 5 Set the tilt speed of current command. speedzoom -5 ~ 5 Set the zoom speed of current command. zooming wide or tele Zoom without stopping for larger view or further view with zs speed, used for joystick control. zs 0~6 Set the speed of zooming, “0” means stop. vx -6 ~ 6 The direction of movement, used for joystick control.
PAGE 306
VIVOTEK 8.27 3D Privacy Mask (capability_image_c<0~(n-1)>_privacymask_wintype = 3Drectangle) n denotes the value of "capability_nvideoin" Note: This request requires admin user privilege Method: GET/POST Syntax: http:///cgi-bin/admin/setpm3d.
PAGE 307
VIVOTEK 8.28 Camera Control (capability.ptzenabled > 0) Note: This request requires Viewer privileges. Method: GET/POST Syntax: http:///cgi-bin/camctrl/camctrl.
PAGE 308
VIVOTEK speedapp -5 ~ 5 Set the auto pan/patrol speed. auto pan Auto pan. patrol Auto patrol. stop Stop camera. wide Zoom larger view with current speed. tele Zoom further with current speed. stop Stop zoom. wide or tele Zoom without stopping for larger view or further view with zs speed, zoom zooming used for joystick control. zs 0 ~ 8 Set the speed of zooming, “0” means stop. vx The slope of movement = vy/vx, used for joystick control.
PAGE 309
VIVOTEK 8.29 Recall (capability.ptzenabled > 0) Note: This request requires Viewer privileges. Method: GET Syntax: http:///cgi-bin/viewer/recall.cgi? recall=[&channel=][&return=] PARAMETER VALUE DESCRIPTION recall string[30] One of the present positions to recall. channel 0~(capability_nvideoin-1) Channel of the video source. return Redirect to the page after the parameter is assigned.
PAGE 310
VIVOTEK The can be a full URL path or relative path according to the current path. If you omit this parameter, it will redirect to an empty page.
PAGE 311
VIVOTEK Technical Specifications Technical Specifications ONVIF FD816B-HT: Vari-focal, P-iris, Remote Focus FD816B-HF2: Fixed-focal Model System Information CPU Multimedia SoC (System-on-Chip) Flash 1Gb RAM 2Gb Video Motion Detection Five-window video motion detection VCA* Line crossing detection, field detection, loitering detection Alarm and Event Camera Features Image Sensor Supported, specification available at www.onvif.org Intelligent Video 1/2.
PAGE 312
VIVOTEK Technical Specifications ONVIF FD8182-T: Vari-focal, P-iris, Remote Focus FD8182-F2: Fixed-focal Model CPU Multimedia SoC (System-on-Chip) Flash 1Gb RAM 4Gb Supported, specification available at www.onvif.
PAGE 313
VIVOTEK Technology License Notice AMR-NB Standard THIS PRODUCT IS LICENSED UNDER THE AMR-NB STANDARD PATENT LICENSE AGREEMENT. WITH RESPECT TO THE USE OF THIS PRODUCT, THE FOLLOWING LICENSORS’ PATENTS MAY APPLY: TELEFONAKIEBOLAGET ERICSSON AB: US PAT. 6192335; 6275798; 6029125; 6424938; 6058359. NOKIA CORPORATION: US PAT. 5946651; 6199035. VOICEAGE CORPORATION: AT PAT. 0516621; BE PAT. 0516621; CA PAT. 2010830; CH PAT. 0516621; DE PAT. 0516621; DK PAT. 0516621; ES PAT. 0516621; FR PAT. 0516621; GB PAT.
PAGE 314
VIVOTEK Electromagnetic Compatibility (EMC) FCC Statement This device compiles with FCC Rules Part 15. Operation is subject to the following two conditions. ■ This device may not cause harmful interference, and ■ This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.