FD8131V Fixed Dome Network Camera Quick Installation Guide English P/N:625018600G Rev. 1.0 6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C. |T: +886-2-82455282| F: +886-2-82455532| E: sales@vivotek.com 簡中 日本語 Français Español Deutsch H.264 • Vandal-proof • IP66 All specifications are subject to change without notice. Copyright c 2012 VIVOTEK INC. All rights reserved. VIVOTEK INC. 繁中 VIVOTEK USA, INC.
English Warning Before Installation Power off the Network Camera as soon as smoke or unusual odors are detected. Keep the Network Camera away from water. If the Network Camera becomes wet, power off immediately. Do not place the Network Camera around heat sources, such as a television or oven. Refer to your user's manual for the operating temperature. Keep the Network Camera away from direct sunlight. Do not place the Network Camera in high humidity environments.
1 Package Contents FD8131V Alignment Sticker Drill hole Cable hole Cable hole Drill h ole Quick Installation Guide / Warranty Card Software CD 5 1 0 0 0 02 2 1 G RJ45 Female/Female Coupler / Screwdriver/ Screws / Clamp Core 2 Physical Description Lens Black Cover MicroSD/SDHC Card Slot Reset Button Status LED EN - 2 Ground Wire General I/O Terminal Block Ethernet 10/100 RJ45 Plug Power Cord Socket
English 3 Hardware Installation First, follow the instructions below to remove the dome cover. Network Camera Model No: FD8131V MAC:0002D107258A V I Dome Cover RoHS This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Pat.
A oh el oh el rD li C ba el oh el C ba el h llir o el Ceiling Mount D Wall Mount e Dril hol A e Cable hol e Cable hol Drill hole 1. Attach the alignment sticker to the ceilling/wall. 2. Through the two circles on the sticker, drill two pilot holes into the ceilling/wall. 3. The Network Camera can be mounted with the cable routed through the ceiling/wall or from the side. If you want to feed the cable through the ceiling/wall, drill a cable hole A as shown in the above picture. 4.
English 4 Network Deployment General Connection (without PoE) 1. If you have external DI devices, make the connection from general I/O terminal block. 2. Use the supplied RJ45 female/female coupler to connect the Network Camera to a switch. Use a Category 5 Cross Cable when Network Camera is directly connected to PC. 3. Connect the supplied power cable from the Network Camera to a power outlet.
When using a non-PoE switch Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE switch. PoE Power Injector (optional) POWER COLLISION 1 2 3 4 5 LINK RECEIVE PARTITION Non-PoE Switch IMPORTANT: lthough the camera and the cable gland on the camera's end are waterproof, the cable A molding at the other end is not waterproof.
English 5 Assigning an IP Address 1. Install “Installation Wizard 2” from the Software Utility directory on the software CD. 2. The program will conduct an analysis of your network environment. After your network is analyzed, please click on the “Next” button to continue the program. 3. The program will search for all VIVOTEK Video Receivers, Video Servers, and Network Cameras on the same LAN. 4. After a brief search, the main installer window will pop up.
7 Adjusting the Lens Based on the live image retrieved from the camera, adjust the camera lens to the desired viewing angle: 1. Turn the lens module left and right. 2. Loosen the tilt adjustment screws on both sides of the camera and then turn the lens module up and down. Upon completion, tighten the screws. 3. Turn the lens to adjust the image orientation.
English To adjust the zoom factor and focus range 1. Loosen the zoom controller and then adjust zoom factor by moving the controller left and right. Upon completion, tighten the zoom controller screw. 2. Loosen the focus controller and then adjust focus range by moving the controller left and right. Upon completion, tighten the focus controller screw. W 8 8 Completion T 1. Align the inner side of the black cover with N the notch on both sides of the lens, fix the black cover. 2.
FD8131V Fixed Dome Network Camera Quick Installation Guide English P/N:625018600G Rev. 1.0 6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C. |T: +886-2-82455282| F: +886-2-82455532| E: sales@vivotek.com 簡中 日本語 Français Español Deutsch H.264 • Vandal-proof • IP66 All specifications are subject to change without notice. Copyright c 2012 VIVOTEK INC. All rights reserved. VIVOTEK INC. 繁中 VIVOTEK USA, INC.
