FD8131 Fixed Dome Network Camera Quick Installation Guide English P/N:625018300G Rev. 1.0 6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C. |T: +886-2-82455282| F: +886-2-82455532| E: sales@vivotek.com 簡中 日本語 Français Español Deutsch Português Italiano Vari-focal • Compact Design • Micro SD/SDHC All specifications are subject to change without notice. Copyright c 2012 VIVOTEK INC. All rights reserved. VIVOTEK INC. 繁中 VIVOTEK USA, INC.
English Warning Before Installation Power off the Network Camera as soon as smoke or unusual odors are detected. Contact your distributor in the event of occurrence. Keep the Network Camera away from water. If the Network Camera becomes wet, power off immediately. Contact your distributor in the event of occurrence. Do not place the Network Camera around heat sources, such as a television or oven. Refer to your user's manual for the operating temperature.
Do not place the Network Camera on unsteady surfaces. Do not touch the Network Camera during a lightning storm. Do not disassemble the Network Camera. Do not drop the Network Camera. Do not insert sharp or tiny objects into the Network Camera.
English 1 Package Contents FD8131 Alignment Sticker Drill hole Cable hole Drill hole RJ45 Female / Female Coupler / Screws / Clamp Core Software CD 5 1 0 0 0 02 2 1 G Quick Installation Guide / Warranty Card FD8131 Fixed Dome Network Camera Quick Installation Guide English 繁中 簡中 日本語 Français Español Deutsch Português Italiano Türkçe Polski Русский Česky Svenska Vari-focal • Compact Design • Micro SD/SDHC EN - 3
2 Physical Description Black Cover Lens Ground wire General I/O Terminal Block Ethernet 10/100 RJ45 Plug MicroSD/SDHC Card Slot Reset Button 3 Status LED Power Cord Socket Hardware Installation First, follow the instructions below to remove the dome cover. Flip the black retention tabs in the counter-clockwise direction to release the dome cover (clockwise if you look from the bottom up.) Dome Cover Network Camera Model No: FD8131 Record the MAC address before installing the camera.
English Then remove the black cover as shown below. Tilt Adjustment Screws A Ceiling Mount A Wall Mount 1. Attach the alignment sticker to the ceilling/wall. 2. Through the two circles on the sticker, drill two pilot holes into the ceilling/wall. 3. The Network Camera can be mounted with the cable routed through the ceiling/wall or from the side. If you want to feed the cable through the ceiling/wall, drill a cable hole A as shown in the above picture. 4.
6. Buckle the supplied clamp core onto the cable to prevent EMI radiation. The clamp core should be installed at least 5cm away from the camera. 5 cm 7. Connect the ground wire to grounded conduit or a grounded metallic surface. 4 Network Deployment General Connection (without PoE) 1. If you have external DI devices, make the connection from general I/O terminal block. 2. Use the supplied RJ45 female/female coupler to connect the Network Camera to a switch.
English Power over Ethernet (PoE) When using a PoE-enabled switch This Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled switch via Ethernet cable. POWER COLLISION 1 2 3 4 5 LINK RECEIVE PARTITION PoE Switch When using a non-PoE switch Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE switch.
5 Assigning an IP Address 1. Install “Installation Wizard 2” from the Software Utility directory on the software CD. 2. The program will conduct an analysis of your network environment. After your network is analyzed, please click on the “Next” button to continue the program. Installation Wizard 2 3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras on the same LAN. 4. After a brief search, the main installer window will pop up.
English 6 Ready to Use 1. A browser session with the Network Camera should prompt as shown below. 2. You should be able to see live video from your camera. You may also install the 32-channel recording software from the software CD in a deployment consisting of multiple cameras. For its installation details, please refer to its related documents. For further setup, please refer to the user's manual on the software CD.
7 Adjusting the Lens Based on the live image retrieved from the camera, adjust the camera lens to the desired viewing angle: 1. Turn the lens module left and right. 2. Loosen the tilt adjustment screws on both sides of the camera and then turn the lens module up and down. Upon completion, tighten the screws. 3. Turn the lens to adjust the image orientation.
English To adjust the zoom factor and focus range 1. Loosen the zoom controller and then adjust zoom factor by moving the controller left and right. Upon completion, tighten the zoom controller screw. 2. Loosen the focus controller and then adjust focus range by moving the controller left and right. Upon completion, tighten the focus controller screw. T W 8 N 8 Completion 1. Align the inner side of the black cover with the notches on both sides of the lens, fix the black cover. 2.
FD8131 Fixed Dome Network Camera Quick Installation Guide English P/N:625018300G Rev. 1.0 6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C. |T: +886-2-82455282| F: +886-2-82455532| E: sales@vivotek.com 簡中 日本語 Français Español Deutsch Português Italiano Vari-focal • Compact Design • Micro SD/SDHC All specifications are subject to change without notice. Copyright c 2012 VIVOTEK INC. All rights reserved. VIVOTEK INC. 繁中 VIVOTEK USA, INC.
