30QT TURKEY FRYER Assembly Instruction THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Warnings ! WARNING ! READ AND UNDERSTAND BEFORE USING THIS PRODUCT Throughout this manual the words appliance, cooker, fryer/boiler, burner and stove will be used interchangeable to refer to the VIVOHOME Outdoor Ranges and Cookers. IF YOU SMELL GAS: 1. Turn off the appliance's gas. 2. Extinguish any open flame. 3. If odor continues, keep away from the appliance and immediately call your Fire Department. 1. This is an ATTENDED appliance.
Warnings instructions in this manual. 10.When cooking with oil/grease, have a Type BC or ABC fire extinguisher readily available. In the event of an oil/grease fire, do not attempt to extinguish with water. Immediately call the Fire Department. A Type BC or ABC fire extinguisher may, in some circumstances, contain the fire. 11.NEVER overfill the cooking pot with oil, grease or water. Follow instructions in this manual for establishing proper oil, grease or water levels. 12.
Warnings property damage, personal injury or death. 20.Use VIVOHOME appliances only in accordance with state and local ordinances, or in the absence of local codes, with the National Fuel Gas Code, ANSIZ223.1/NFPA 54, Storage and Handling of Liquified Petroleum Gases, ANSI/NFPA 58 or CSA B149.1, Natural Gas and Propane Installation Code.
Maintenance & Care 1. The area where the cooker will be used must be kept clear and free from combustible materials, gasoline and other flammable vapors and liquids. Before each use of the cooker, inspect and remove any combustible items. 2. The flow of combustion and ventilation of air must not be obstructed. The cooker must be set in an open area with 10 ft. (3.05m) of space on all sides and no roof or overhang overhead. Check the location and placement of the cooker before each use. 3.
Maintenance & Care 4. Thermometer: Clean after each use with mild soapy water and a dry towel. Do not submerge in liquid or put in dishwasher. TIPS FOR CARING FOR ALUMINUM FRY PANS AND BOILING POT It is not necessary to season aluminum pots before cooking with them. Wash with a liquid dish washing detergent and a dry towel. After cooking, wash aluminum pots and fry pans in hot, sudsy detergent.
Lighting & Operating Instructions ! WARNING ! NEVER PUT HANDS OR FACE DIRECTLY OVER BURNER WHILE LIGHTING OR WHILE THE APPLIANCE IS LIT FOR MODELS WITH ADJUSTABLE REGULATORS (ILLUSTRATIONS PAGE 7) 1. Check the casting to make sure it is set up as per the illustration (Figure 1). 2. Make sure that the regulator control is turned OFF by turning it counterclockwise until it reaches the stop. 3. Open cylinder control valve by turning it counterclockwise as per the diagram (Figure 2). 4.
Lighting & Operating Instructions (Figure 3). When lighting the burner, if ignition does not occur in 3 to 5 seconds, turn the manual valve(s) and cylinder control off. Wait 5 minutes for gas to disperse. Repeat the steps. 5. Check that the flame is blue and that the flames are emitted from every port in the casting. If not, rotate the air shutter position until there is a blue flame. Opening the shutter too much will cause the flame to “Lift” off the burner (Figure 6).
Lighting & Operating Instructions ! WARNING ! NEVER MOVE THE COOKER OR POT WHILE IT IS IN USE OR STILL HOT [ABOVE 100°F (38°C)] TURNING OFF AND STORING THE COOKER AFTER USE 1. After each use, turn OFF the cooker at the regulator/manual valve first, then at the gas cylinder valve. Check to make sure this is no flame and all valves are off. Do not leave the cooker until it has cooled completely. When removing food from the cooker wear protective mitts. 2.
Parts List and Diagram Before assembling the product, ensure that your package has the following parts. If any of the parts are missing or defective, please contact customer service for help.
Assemble steps Step 1 Connect Part B to Part A with Part L screws. A B (3pcs) L (6pcs) Step 2 Connect Part C to the main body with Part L screws.
Assemble steps Step 3 Connect Part D and Part E with a wrench. E D ＋ D E Step 4 Use Part M screws to connect the assembled Part D and Part E to the main body.
Assemble steps Step 5 Connect Part F to the main body with Part L screws. F (2pcs) L (4pcs) Step 6 Place the Part G pot on the main body (a thermometer can be placed on the edge of the pot).
