Preface Copyright ©2012 Vivitek Corporation. is a trademark of Vivitek Corporation. Other trademarks are the properties of their respective owners. Values, weights and dimensions are approximate. Specifications are subject to change without prior notice. Disclaimer The information in this document is subject to change without notice.
Important Safety Information Important: It is strongly recommended that you read this section carefully before using the Qumi. These safety and usage instructions that will make sure you enjoy many years of safe use of the Qumi. Keep this manual for future reference. Symbols Used Warning symbols are used on the unit and in this manual to alert you of hazardous situations. The following styles are used in this manual to alert you to important information.
Qumi Installation Notice • Allow at least a 50cm clearance around the exhaust vent. Minimum 100mm Minimum 500mm • Make sure that the intake vents do not recycle hot air from the exhaust vent. • When operating the Qumi in an enclosed space, make sure that the surrounding air temperature within the enclosure does not exceed operating temperature while the Qumi is running, and the air intake and exhaust vents are unobstructed.
Power Safety • Only use the supplied adapter. • Do not place anything on the cord. Place the cord where it will not be in the way of foot traffic. • Remove the battery from the remote control when storing or not in use for a prolonged period. Cleaning the Qumi • Unplug the cord before cleaning. See Cleaning the Qumi on page 28. Note: The Qumi will be warm after usage. Allow Qumi to cool down before storing in a compartment.
Table of Contents Preface................................................................................................................... ii Chapter 1 At a Glance................................................................. 1 Overview................................................................................................................. 1 Accessories............................................................................................................ 3 Remote Control................
Chapter 1 At a Glance Overview Front/Top/Right View Keypad See Keypad - On-Screen Display (OSD) buttons Cooling Vent Cooling Vent Do not cover Do not cover Lens Focus ring Projection Lens Keypad Focus the projected image Menu Open and exit the OSD buttons Up Cursor Navigate and change settings in the OSD Enter Cursor Change settings in the OSD Left Cursor Right Cursor Navigate and change settings in the OSD Navigate and change settings in the OSD Down Cursor Navigate and change settin
Rear/Top/Left View DC IN Connect the supplied power adapter Power Switch AUDIO OUT Turn on/off the Qumi Connect an audio cable to speakers or headphones UNIVERSAL I/O AV IN Connect a RGB or component cable from a device Connect the AV IN cable from a video device MINI HDMI USB Connect a MINI HDMI cable from a HDMI device For service use IR Receiver Receive IR signal from the remote control Bottom View Rubber Foot Pad Stability and maintain cooling ventilation Cooling Vent Do not cover 2
Accessories Along with the Qumi, the following accessories are included: Remote Control (With one 3V CR2025 battery) VGA Cable Regional Power Cord and Power Adapter W A R R A N T Y Documentation Kit (Quick Start Guide, Warranty Card) Cable Cores* Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. It is recommended that you keep the original packing material should you ever need to return the equipment for warranty service.
Remote Control Up Cursor Navigate and change settings in the OSD ON/OFF Tuen on or off Qumi Right Cursor Enter Navigate and change settings in the OSD Change settings in the OSD Exit Left Cursor Close the OSD Navigate and change settings in the OSD Down Cursor Navigate and change settings in the OSD Menu Open and exit the OSD Mute Source Mute the audio Change the input source Important: 1. Be sure nothing obstructs the path between the remote control and the Qumi.
Chapter 2 Getting Started What You Need Many types of external devices and peripherals can be connected to the Qumi. DVD, VCD and VHS players can be connected to play movies. Camcorders and digital cameras can also be used to play videos. Computers can be connected to display documents and other types of media stored on the computer. These devices can be connected to the Qumi by using an appropriate cable. Make sure that the connecting device has an appropriate output connector.
Setting Up Qumi Connecting Apple® Devices (Optional) Connect an Apple® device to the Qumi by using the following: Apple® Connection Kit iPhone iPod iPad VGA to Apple® Video Adapter (Optional) iPhone iPod iPad (Available at Apple Store) Connecting Peripherals by HDMI (Optional) Connect HDMI-compatible peripherals to the Qumi using the Mini to Standard HDMI cable.
Connecting Personal Computers Connect a personal computer to the Qumi by using the VGA cable. Personal Computer Note: The personal computer must have a VGA output port to use the VGA cable to connect to the Qumi. Connecting Video Connect video devices to the Qumi by using the audio/video cable (optional accessory). Game Console DVD Player Connecting Audio Connect earphones or mini speakers to the Qumi by inserting into the Audio Out port.
Starting and Shutting down the Qumi 1. Connect the AC power adapter to the Qumi. Connect the other end of the AC power adapter to a wall outlet. Note: Adapter models may vary between regions. 2. Then slide the POWER switch to turn on the Qumi. The Qumi splash screen displays and connected devices are detected. See Setting an Access Password (Security Lock) on page 9 if security lock is enabled. 3.
4. Slide the POWER switch to turn off the Qumi. Adjusting the Image If the projected image is not clear, the image can be adjusted by moving the focus ring up or down until the image is clear. Setting an Access Password (Security Lock) To prevent unauthorized use of the Qumi, you can create a password. When the access password function is enabled, the password must be entered after the Qumi has been turned on. Creating a password can be done by performing the following steps: 1. 2.
3. 4. 5. Press the ▲ or ▼ button to select Security Lock. Press the ◄ or ► button to enable or disable the security lock function. A password dialog box automatically appears. You can use the ▲▼◄► buttons located either on top of the Qumi or on the remote control to enter the password. Any combination of the navigation buttons can be used (five must be chosen). Press the navigation buttons in any order to set the password. 6. Then press the MENU button to exit the dialog box.
Setting Up the Remote The remote control comes with one (1) 3V lithium battery (CR2025). The battery is pre-installed in the remote control. To begin using the remote control, remove the plastic tab (A) from the battery compartment. A Replacing the Remote Control Batteries 1. A Remove the battery compartment cover by sliding the cover towards the arrow (A). Then pull out the cover towards the arrow (B). 2. Remove the old battery and insert the new battery with the positive side facing up. 3.
Chapter 3 On-Screen Display (OSD) Settings OSD Menu Controls The Qumi has an On-Screen Display (OSD) settings menu that allows you to make adjustments and changes to settings, such as display settings and audio settings. There are 5 menus within the OSD menu: • Image – Various aspects of the image quality can be adjusted in this menu. • Computer – Settings for personal computers can be adjusted in this menu. • Video/Audio – Many settings for video and audio can be adjusted in this menu.
Setting the OSD Language The language that is displayed in the OSD can be changed. To change the language in the OSD, perform the following steps: 1. Enter the OSD menu. Press the ◄ or ► button to select the Installation I menu. 2. Press the ▲ or ▼ button until the cursor highlights the Language setting. 3. Press the ◄ or ► button until the language you want is shown in the cursor. 4. Press the EXIT button or MENU button twice to close the OSD.
OSD Menu Overview Use the following illustration to quickly find a setting or determine the range for a setting.
OSD Sub-Menu Overview 15
Image Menu To access the Image menu and adjust the settings, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Image menu. 3. Press the ▲ or ▼ button to move the cursor up or down in the Image menu. 4. Press the ◄ or ► button to change values for each applicable setting. ITEM DESCRIPTION Display Mode Press the ◄ or ► button to set the Display Mode. Brilliant Color Press the ◄ or ► button to adjust the Brilliant Color value.
Advanced Feature To access the Advanced menu and adjust the settings, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Image menu. 3. Press the ▲ or ▼ button to move to the Advanced menu and then press . 4. Press the ▲ or ▼ button to move the cursor up or down in the Advanced menu. ITEM DESCRIPTION Color Space Press the ◄ or ► button to adjust the color space. Color Temperature Press the ◄ or ► button to adjust the color temperature.
Computer Menu To access the Computer menu and adjust the settings, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Computer menu. 3. Press the ▲ or ▼ button to move the cursor up or down in the Computer menu. 4. Press the ◄ or ► button to change values for each applicable setting. ITEM DESCRIPTION Horizontal Position Press the ◄ or ► button to adjust the display position to left or right.
Video/Audio Menu To access the Video/Audio menu and adjust the settings, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Video/Audio menu. 3. Press the ▲ or ▼ button to move the cursor up and down in the Video/Audio menu. 4. Press the ◄ or ► button to change values for each applicable setting. ITEM DESCRIPTION Video AGC Press the ◄ or ► button to enable or disable the Automatic Gain Control for video source.
Audio To adjust the audio settings, press to enter the Audio sub menu. ITEM DESCRIPTION Volume Press the ◄ or ► button to adjust the audio volume. Mute Press the ◄ or ► button to turn on or off the audio. Audio Input Press the ◄ or ► button to select audio input.
Installation I Menu To access the Installation I menu and adjust the settings, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Installation I menu. 3. Press the ▲ or ▼ button to move the cursor up or down in the Installation I menu. 4. Press the ◄ or ► button to change values for each applicable setting. ITEM DESCRIPTION Language Press the ◄ or ► button to select a different localization menu.
Advanced To adjust the advanced settings, press to enter the Advanced sub menu. ITEM DESCRIPTION Security Lock Press the ◄ or ► button to enable or disable security lock function. Keypad Lock Press the ◄ or ► button to enable or disable keypad lock function. Presentation Timer Press to enter the Presentation menu. Presentation Timer To adjust the presentation timer settings, press menu.
Installation II Menu To access the Installation II menu and adjust the settings, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Installation II menu. 3. Press the ▲ or ▼ button to move the cursor up or down in the Installation II menu. ITEM DESCRIPTION Auto Source Press the ◄ or ► button to enable or disable automatic source detection. Auto Power Off (min) Press the ◄ or ► button to automatically turn the projector lamp off when there is no signal.
Advanced Feature To access the Advanced menu and adjust the settings, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Installation II menu. 3. Press the ▲ or ▼ button to select the Advanced menu and then press . 4. Press the ▲ or ▼ button to move the cursor up or down in the Advanced menu. 5. Press the ◄ or ► button to change values for each applicable setting. ITEM DESCRIPTION OSD Menu Setting Press to enter the OSD setting menu.
OSD Menu Setting ITEM DESCRIPTION Menu Position Press the ◄ or ► button to select different OSD location. Translucent Menu Press the ◄ or ► button to select OSD background translucent level. Menu Display Press the ◄ or ► button to select OSD timeout delay. Peripheral Test ITEM DESCRIPTION Remote Control Test Press to test the IR remote controller for diagnostic. Color Test Press to select different colors on screen. Button Test Press to test the button on keypad.
3D ITEM DESCRIPTION 3D Press the ◄ or ► button to select Off, DLP-Link or IR. 3D Sync Invert Press the ◄ or ► button to turn 3D Sync Invert On or Off. Factory Reset To reset all of the menu items to the factory default values (except Language and Security Lock), perform the following steps: 1. Press the ▲ or ▼ button to move the cursor up or down in the Installation II menu. 2. Select the Factory Reset sub menu. 3. Press .
Status To see the status of the Qumi, perform the following steps: 1. Press the ▲ or ▼ button to move the cursor up or down in the Installation II menu. 2. Select the Installation II sub menu. 3. Press to enter the Status sub menu. ITEM DESCRIPTION Active Source Displays the activated source. Video Information Displays resolution/video information for RGB source and color standard for Video source. LED Hours LED use information is displayed (in hours). Eco and Normal counters are separated.
Chapter 4 Taking Care of Your Qumi Cleaning the Qumi Cleaning the Qumi to remove dust and grime will help provide trouble-free operation. Warning: 1. The Qumi should be turned off and unplugged before cleaning. Failure to do so may result in injury or damage to the system. 2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings on the Qumi. 3.
Troubleshooting Common Problems and Solutions These guidelines provide tips to deal with problems you may encounter while using the Qumi. If the problem remains unresolved, contact your dealer for assistance. The problem sometimes can be as simple as a wire that is not completely connected. Review the following possible issues before proceeding to the problem-specific solutions. • Use another electrical device to confirm that the electrical outlet is properly working. • Make sure that the Qumi is turned on.
Image Problems Problem: No image appears on the screen 1. Verify that the settings on your personal computer are properly configured. 2. Turn off all of the equipment and power up the equipment again in the correct order. Problem: The image is blurred 1. Adjust the Focus on the Qumi. 2. Make sure the Qumi-to-screen distance is within the specified range. 3. Clean the Qumi lens with optical lens cleaning cloth if it is dirty. Problem: The image is wider at the top or bottom (trapezoid effect) 1.
Audio Problems Problem: There is no sound 1. Adjust the volume of the audio source. 2. Check the audio cable connection. 3. Test the output of the audio source with other speakers. 4. Have the Qumi serviced. Problem: The sound is distorted 1. Check the audio cable connection. 2. Test the output of the audio source with other speakers. 3. Have the Qumi serviced. FAQs 1. Does Qumi work with a personal computer, notebook or netbook? Yes. Use the provided VGA cable or HDMI cable.
6. How long will the LED light source in the Qumi last and can it be replaced? The Qumi does not use a typical Qumi lamp. It uses a set of Light Emitting Diodes (LED) to illuminate and project images. LED’s have a greater lifespan than conventional lamps. Qumi LED’s are estimated to last for approximately 30,000 hours. The lifespan of the LED depends on factors such as brightness, usage, environmental conditions. LED brightness can decrease over time. The LED module is not replaceable. 7.
Specifications Model Qumi Q2-L Series Resolution HD (720p - 1280x800) Projection Distance 1000mm ~ 3000mm (39.37” ~ 118.11”) Projection Screen Size (Diagonal) 762mm ~ 2286mm (30” ~ 90”) Projection Lens Manual focus Throw Ratio 1.
Projection Distance vs. Projection Size Projection Distance and Size Table IMAGE DIAGONAL (MM/INCHES) IMAGE WIDTH (MM/INCHES) IMAGE HIGH (MM/INCHES) PROJECTION DISTANCE (MM/INCHES) OFFSET-A (MM/INCHES) 762/30 646/25.43 404/15.91 1000/39.37 10/0.40 1016/40 862/33.94 538/21.18 1340/52.76 13/0.51 1143/45 969/38.15 606/23.86 1500/59.06 15/0.59 1270/50 1077/42.40 673/26.50 1670/65.75 17/0.66 1524/60 1292/50.87 808/31.81 2000/78.74 20/0.79 1778/70 1508/59.37 942/37.09 2340/92.
Timing Mode Table SIGNAL RESOLUTION H-SYNC V-SYNC COMPOSITE / COMPONENT RGB DVI/HDMI (KHZ) (HZ) S-VIDEO 15.734 60.0 O — — — NTSC — PAL/SECAM — 15.625 50.0 O — — — 720 x 400 37.9 85.0 — — O O 800 x 600 31.5 60.0 — — O O 800 x 600 37.9 72.0 — — O O 800 x 600 37.5 75.0 — — O O 640 x 480 43.3 85.0 — — O O 800 x 600 35.2 56.0 — — O O 800 x 600 37.9 60.0 — — O O 800 x 600 48.1 72.0 — — O O 800 x 600 46.9 75.
Qumi Dimensions 102.4mm (4.03”) 160.0mm (6.3”) 32.3mm （1.27″ ） 160.0mm (6.
Regulatory Compliance FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
