Safety on the road.________________________________ Please remember that using a mobile phone during driving is prohibited. Follow the rules as applicable in each country. Stop the car in a safe place if you need to answer or use the phone. Please always remember the following before using the phone in emergencies. Focus on driving only. Remember the most considerable thing is nothing but your safety. If you want a Hands-Free device on vehicles, let it installed by an authorized engineer.
Infrared equipment and safety ______________________ This phone includes infrared transmission equipment. Do not let infrared rays come in contact with eyes of others nor use together with other infrared equipment. Electrical equipment ______________________________ Most electric appliances are secured and protected against the effect of the phone radio frequency. Nevertheless, there are some products that are not protected against.
Battery and parts _________________________________ This phone uses a rechargeable battery of Lion Technology. The battery if completely recharged is usable to call for a duration of 230 minutes and available for standing-by for a duration of 180 minutes. Do not use any charger or battery if damaged or worn out. Do not touch any circuit of the battery. It will cause damage thereon. If the battery is kept in hot temperature, its function and duration may be deteriorated.
2. Cellular Phone Opening/commencement of the phone _______________ Slightly push the upper from down below to open the phone. If the phone is turned on, a lamp will be on the screen. The screen will be off if the phone is shut. Button __________________________________________ Arranged shapes and basic names of the buttons used on GRUNDIG mobile are as shown below; On/Off button Keep pressing this button to turn the phone on and off. Press this button to finish the call.
Direction button It allows the user to move to 4 directions (up and down, right and left) from the phone menu . Option list can be selected with this button. Press the square button (OK) in the center to select the list presently positioned. When camera mode is positioned, press this central button to take a picture. On the basic screen press the central upper button to display the call record. In the same way press the central bottom button to display the address book.
Select button Select button of Left Right executes the option right above. Send button After pressing desired phone number, press the send button the call to the number. If the line is not busy, press this button to show the phone numbers called before. to start LED display Down below the direction button blue LED blinks every 2 seconds to let you know the phone is turned on. If GRUNDIG mobile is recharged with the phone off, this LED will be turned on the same.
In the beginning __________________________________ Installment of SIM card To answer the phone or to call, GRUNDIG mobile needs a SIM card available, which the communication company may have installed already. Note If GRUNDIG mobile is used, installation state of the SIM card will be displayed. If the SIM card is not installed, a paragraph Confirm SIM card will be displayed. Installment of SIM card 1- Remove the battery after pulling the hook outward with GRUNDIG mobile turned off.
3 - As for the two holes, make sure the cover on the rear fits well to insert the battery. Finally, keep pressing the lower of the cover till it sounds Tic . 3 - Pull the hook and insert the cover and the battery. Note Follow these procedures or some defects may occur on the support parts of the entrance, which will not be guaranteed. Battery charge 1- Insert the charger as shown in the figure.
2- If the charge is completed, the screen will be as shown in the figure. To remove the charger hold and press the both ends to extract. Phone ON/OFF ___________________________________ Keep on pressing the red button for 5 seconds to turn on the phone. This function is designed to avoid unintentional ON or OFF of the phone when kept in a pocket or luggage. Start If PIN enable setting on after the phone is turned on, you will be required to input 4-digit password.
If the time is correct, press OK button. If the time is not correct, input new time and then press OK button. Stand-by screen Note For about 1 minute and 30 seconds after the phone is on, its image and menu may be displayed a little slower than usual. This delayed time is for environmental setting of the menu. And the menu will not be displayed during this duration. After this duration, the speed will be back to normal. Stand-by screen is displayed when the phone is available to answer or use to call.
Upper part *It is a line to display the status of the phone with various icons. *It is a line to display the status of the phone company providing the mobile services. Central part: If the phone is not available yet for services, bumpy paper type of background is displayed, where main menus are displayed here too. Lower part: On the top, day, month, year and present time will be displayed. On the bottom, optional menu button will be displayed as a selection button.
The direction button will be used mainly to appropriate functions of the phone. - Keep on pressing Start/End button in stand-by screen state to turn off the phone. - When the screen is in a normal state, press Send Button to display the call record. - In order to make a call, press number first in stand-by screen state and the call button next. Keep on pressing one number among 2, 3 and 7 and a call to the number as input will be made.
Icons displayed in stand-by screen state _____________ Icon Name Description Always displayed to show service area if Antenna/GPRS reached Substituted for Antenna icon to show GPRS connection GPRS area if reached Always displayed to show service Service available level available level (0 to 5) in a bar graph The greatest service available level with Service available level A the maximum bars There are 6 modes available (sound Bell mode only, vibrate only, sound after vibrate, sound with vibrate,
Battery lef Alarm Displayed approximately to show the actual capacity of the battery state Displayed if alarm is set via the calendar Calls ___________________________________________ Making a call To make a call, press desired phone number in stand-by screen state and then Call Button (blue) . If you input the wrong number, press Clear Button (CLR) to delete the last number input.
If SIM card or the memory of the phone is displayed automatically, specify a related type of the phone too. (Refer to the user manual for more detailed procedures) Answering the phone Press Call (receive) Button to answer the phone call. Press Start/End Button not to answer the phone call. Whole menus ____________________________________ In the stand-by state, press the menu button to go back to standard menu. Press the direction button (up/down/left/right) to get into menu desired.
WAP 5 To move to wap service menu To look through call record and Calls 6 voice messages sent and received To use calendar, calculator, Extras downloading program, 7 information on various events (meeting, birthday), etc.
Writer Writer is used to input phone number, text or number. All kinds of writers (phone number, number, text) have their own functions respectively. Writer of phone number It is used to input phone number from the phonebook. Above all, press number in stand-by screen state to get into the screen of writer function. 0 ~ 9 are available to enter, which has the following features. * Press 0 to display + character. * Press <*> and <#> to input characters of <*> and <#> respectively.
* Press OK/Save/Enter button (menu displayed on the left of the screen) to go to next step. Press Previous Button to go back to the previous step of the screen. * Press Navigator Button (up/down/left/right) to move the cursor to the direction as designated. Writer of number It is used to input password 1, password 2 and call-restricted password. Press the following buttons to make use of its functions specified. * Use the buttons 0 to 9 to press such number 0 to 9 as applicable.
automatically. In case with Smart Input accompanied, this will make the first letter be a capital letter, and the rest be small letters automatically. In case with Number Input (1), number input is available fast. (Press number 0 to 9 to display 0 to 9 as applicable, and press # button to display the decimal point.) Note Press <*> shortly to change input sequence as follows; AB, ab, Ab, 1. Input method is displayed between the two menus in the center of the bottom line of the screen.
Multi Input This method operates differently according to the language specified. If Spanish has been specified, following text will be displayed when you press one numeric button repeatedly. Button Press 1a Press 2a Press 3a Press 4a Press 1 Space 2 A/a 3 D/d E/e 4 G/g 5 J/j 6 7 5a Press 6a Press .
which can display special characters which are not available in general text mode. Move the direction button (up/down/left/right) on the text desired to select those special characters. If you seleted the special charater, press OK button to input applicable character. Characters available are as follows; All the input methods and all the languages available in GRUNDIG Mobile have been summarized in the following table.
3. Phonebook In address book, phone number, name and other information are saved and displayed. There are three points of contact in address book. 1. SIM: Information related with contact is saved in SIM memory only. 2. Only the phone: Information is saved in phone memory only. 3. Double (copy): Name and phone number of these contacts are saved in SIM memory and phone memory. Besides, there are three address books. 1. Mixed Phonebook: Shows all contacts saved in SIM memory and phone memory. 2.
under the screen. * Up to 14-character and 20-digit input can be saved in the phone book. (If the first text input is some symbol to represent international call, up to 21 is available) * Up to 4 phone numbers are available for a name. * Up to 250 addresses can be saved in SIM memory. (The number of addresses available differs from each other according to card capacity) * Up to 500 entries can be saved in phone memory.
Remember the icon will disappear from this line if the contact is a group. Up to 750 contacts can be shown via the whole address book (phone memory plus SIM card memory in total) How to enter Mixed Phonebook There are two methods to get into whole address book. - Press downward direction button in background screen. - In the basic menu screen, press Select Button while address book icon is selected. To make a call, select the one desired and press Call Button .
* Delete contact * Delete All * Copy contact to phone / SIM * Change Phonebook * New group * Search * Receive card(s) * Own number * Memory status And options for group are as bellow; * View group * Send message to group * New group * Rename group * Delete group * New contact * Receive card(s) * Change Phonebook * Memory status 34
The function of each option is as follows; In order to select one of them, select direction button first and then press Select Button. View card This option shows details on contact being selected. (See the figure below) *Name of contact is used as a title of View Card. *It shows phone number of contact selected. *Even if contact is empty since saved in phone address book, it always displays E-mail address icon and reference . *Information correspondent to contact is displayed in the following order.
Attached image Attached sound Group joined Note Use SIM card to display the phone number of the name selected only. Press Previous Button to go back to the previous screen. Press option button to display options which can be applied to the name selected. Call contact It makes a call to the name (person) selected. Send a message It sends a message to the name selected. Modify This option if selected can change the information of the name selected.
Name option function Edit Name: This option always appears regardless of the name selected. It changes the selected name to a different name.Even though the name saved in both sides is selected and changed, there will no effect on the both memories. Changing name which is saved in both sides will be different between the two (SIM, phone):SIM memory keeps the name as before but the phone memory saves the changed name.
group type (home, company, etc.) of the selected phone number. Copy Number copies the number to phone. Change phone typr Change the type of phone number Copy number to SIM: copies selected number to SIM card or phone number memory from the present location. Copy number to FDN: Fixed Dial number (FDN) functions to allow calls to be sent only to designated groups and specific phone numbers. And this option is used to copy selected phone numbers from FDN of SIM address book.
Delete contact deletes a selected name and its whole information contained. You will be asked to confirm before starting this option. Erase number: deletes presently selected name s number or E-mail address, etc. You will be asked to confirm before starting this option. Copy number to SIM(or phone) copies selected phone number to SIM card or phone memory from the present location.
Card photo It is used to set desired image for selected contact. Select this option to display my picture screen and there select desired picture. Send card This option sends saved data in memory card to specific contact via infrared. Select this option to display send card screen and select via IR to use it. Call Contact It is the second option of the address book. Select number input in the previously selected contact to make a call.
New contact This option adds new contact to address book. Select this option to display the following screen. Note: New contact can not be made directly to whole address book. For this operation, you should make it first in SIM or phone address book and then copy the contact to address book next. Select In phone memory to make contact in address book. Select In SIM memory to save contact in card. Select option as desired and press Select button.
Input number with numeric buttons and then press OK button to save this number in memory and to display option screen of type. From here select the type of the phone number (home, mobile, work, fax.) and press Enter button. Press Previous Button to return to address book screen again and the name just input will be displayed. Send message This option is used to send SMS (short message) or MMS (multimedia message) to previously selected contact.
* Send: sends a text message to a receiver with this option designated (Press Enter button). * Add new recipient: selects other SMS message receivers. To enter receiver setting screen, press Enter button to display the screen, and there write receiver s name desired or press the name to enter address book to select receivers. * Recipient list: If this option is selected, previously selected list of receivers of text messages will be displayed.
* Insert: inserts selected Picture, animation, melody, sound, symbol and Template to a message to send. For example, you may select sound from the list as desired to insert. (When you selected, melody will sounds for a little while). The selected sound or melody will be heard when its receiver confirms the message. In this manner, choose Template option to select text prepared before on the list (e.g. Vergent! Please call! Where are you? etc.
To: where message receiver s contact will be displayed. CC: where other receiver s contact will be displayed. Subject: where title of message to send will be displayed. Message: where text message to send will be input. * Press option to add a new receiver. First, press option button, select Add recipient option and then press Select to get into number input screen. And there, write receiver s number or press name button to select in a address book list.
Send message: If this option is selected, you may send the just written message to previously selected receiver(s). Edit text: It is used to edit text. (You may change text using Write Text or Delete Text function in the option menu of previously written text.) Remove text: It is used to remove the pre-inputted text. Add picture: It is used to attach picture or image already saved in the phone. Select the memory(internal or external) what you want to use and select the image to attach.
MMS priority: displays priority of multimedia messages sent. (High, Medium, Low) MMS information: displays various details included in message. (It is a brief list.) Sende s name, receiver s name, title, specified priority, date sent, message capacity, etc. Delete contact deletes selected contact from address book. How to delete from whole address book is as follows; Contact type Execute Mixed Phonebook If Delete Contact option is selected, screen will be displayed to confirm.
Press No/Cancel to cancel the execution. Press Yes to delete contact, a message Operation complete! will appear. After that, address book list will be displayed again. (You can see the deleted details.) Delete all: deletes all contacts saved in selected address book (SIM, cell phone or whole address book). Copy contact to SIM: used to copy selected contact. You should copy only the name and number of contact as expected.
If you want to copy contact saved in SIM or cell phone memory, or if the contact with the same name exists, you should newly make the contact with the same name in both memories (Including all the phone numbers which belong thereto). (However, the phone number will not be changed) During copying contact, In progress screen will be displayed. Completed or Error in progress screen will be displayed to inform you of the state.
New group specifies group of contacts. The group of contacts means a meeting for user to send call and message to at once. For example, if one group is classified into family, friends, co-workers, etc., you may use this option conveniently to send the same message to all the members of a specific group as classified. Specify groups as applicable to receive group messages. Up to 5 groups available. Follow the procedures below to specify a group with new contact. 1. Select New Group on option screen.
b. Create member: In order to make a new member in a group, contact, its phone number and other procedures than described above for Make New Contact shall be fulfilled. c. Remake group: displays the screen to change previously specified group name to another name. 6.
Receive card It receives a phonebook data from PC through an infrared port. If this option is selected, Receive card screen appears, where Via infrared rays option is available. Press Enter button to start to receive messages via an infrared device. If transmission is normal, new card will be added to address book. Own number My phone number(s) is saved in special address book inside SIM card. Select My Number option on the phone call service menu and press Enter to have access to this function.
Memory status This option is used to confirm the capacity and the condition of SIM card or phone memory. On the state window, the following information is provided.
* Memory status Functions of these options are as follow; View group It is used to view all the members belonging to selected group. On the list select a member and press/Option button to apply the followings: Make a call to members, Delete, Add new member to group, Group melody or image setting. Send message to group It is used to send SMS text message or MMS multimedia message to selected group members. * In the first case (text message), SMS message screen will be displayed to write message.
1. Select message on new MMS screen. 2. Press Select button to display message screen. 3. Press Select/Option button and select Send Message on the list displayed (first option of the list). 4. Press Ok button to send the message. New group This option is used to add new group to address book. Select new group on Select screen and press Ok button to display Group Name screen. How to use this screen and its options has been described above (see New Group).
New Contact It is used to add new contact to address book. Select New Contact on option screen and press Ok to display option screen. How to use this screen and its options has been described above (see New Contact) Receive card It is used to receive card through infrared port. If this option is selected, Receive card screen appears, where Via infrared rays option is available. Press Ok button to start to receive messages via infrared. If transmission is succeed, new card will be added to address book.
3. Press option button to display option screen. 4. Select Change Phonebook and press Ok to display Change Phonebook screen. 5. Select the last option on this screen and press OK button to set and apply Terminal phonebook. Note: From now on, the Terminal phonebook will operate till other type of phonebook is selected (even if GRUNDIG mobile is turned off).
1. Press menu button on background screen to display main menu with phone options. 2. Select Phonebook and press Ok to display address book screen. 3. Press option button to display option screen. 4. Select Change phoneBook and press Ok to display Change phonebook screen. 5. Select the second option on the screen and press OK button to set and apply SIM phonebook. Note: From now on, the SIM phonebook will operate till other type of phonebook is selected (even if the terminal is turned off).
4. Messages The menu defined as message allows text message, multimedia message, chatting, cell phone mailing, and connection to environmental services for messages. Follow the procedures below to connect to message menu. 1. Press menu button in stand-by screen state of GRUNDIG mobile to display main menu. 2. Press the direction button to select message menu (second options available on the first line) 3. Press Enter button to display message items on main menu.
Receive text _____________________________________ Text message If receiving a new text message, the phone (SMS and EMS) will sound (sound can be cancelled if requested). And a screen appears to display the number of messages received. Press View button to confirm the new text message, and press Back button to return to the previous screen. * Open: opens the text message for you to read its details. * Send: sends a message to other phone registered. * Erase: deletes received messages from the list.
Recovery display can be defined as specified in the described procedures in . Send new message _______________________________ As previously described, two different types of messages can be sent. * One is short message (SMS) composed of text only and the other is multimedia message (MMS) composed of text, image and music. How to use these is as follows; SMS message Follow the procedures below to send a new SMS message. 1.
SMS message, New message _______________________ Follow the procedures below to go to the menu related with Write text message. 1. Go to message menu. 2. Select new message and move the cursor on short message option. 3. Select Enter 4. Write text to send as desired. 5. Press option button. It will display the following options on the screen. * Introduce recipient: displays receivers of message. You may select receiver s name using phonebook or directly input phone number.
* Input : allows user to insert some object in a message. For example, image (simple static picture), animation (small moving picture), melody (music), sound (simple bell), symbols (press <#> button to display text writer to select symbol as desired thereon), or Template which are available. Insert one of 4 objects in a message to display a series of icons on the message (simple musical note, square) * Dictionary: makes spelling dictionary on or off.
* Add new recipient: adds a new receiver of message. * Recipient: shows the list of receivers of message. Press option button to input a new receiver or to delete the existing receiver * Other options (Save, Alphabet/Number mode, Insert, Dictionary, Send option) are previously described. Multimedia message Follow the procedures below to send a multimedia message. 1. Press new message on message menu. 2. Select multimedia message and press Ok. 3. Write the following; (see the figure below) a.
b. Cc: where other receiver s contact will be displayed to receive copy of message. How to select receivers is as described previously. You may input several phone numbers or E-mail addresses to send a message to many receivers at a time through address book screen. c. Subject: where title of message will be displayed. Select this option and press Select button to go to Subject screen described previously to input up to 100 characters. d. Message: where details of message are written.
Select View button to see the message right after it is received. And press Previous Button to read it later. If Previous Button is pressed, envelopeshaped icon will be displayed on the upper of main menu screen, which means there is a massage not read yet . View saved message not read yet Follow the procedures below to read new message saved. 1. Select Inbox on message menu and press option button. 2. Following options are available on the Inbox menu. a.
* Reply: displays Write Text Screen to replay to the message received. Write message as desired. If you want to know how to write and send text message (SMS), refer to . * Forward: delivers the received message to others. Input the phone number directly thereon or select a receiver on address book. Then press OK button. * Call: makes a call to message sender¡fls number.
Select phone number and press option button to send phone number, MMS and SMS message making use of Save address book, Make a call and MMS & SMS message. Select E-mail address and press option button to send MMS to the selected mail address or use MMS or SMS to send the mail address. Press option button with URL address selected to send the selected URL using SMS or MMS, to save the URL in WAP address book, and to have access to the address with its connected WAP page open. b.
Out box _________________________________________ It is the place all sent messages are saved (messages sent or saved after written). The sent box saves two types of messages, which are SMS (text message) and MMS (multimedia message). Follow the procedures below to go to the sent messages box. 1. Press menu button on main menu screen. 2. Select message icon and press Ok buttons. 3.
1. Write: edits all information related with To, Cc, details or message. 2. Resend: resends text message 3. MMS information: displays brief information related with multimedia message. 4. Delete: deletes multimedia message. 5. Delete all: deletes all multimedia messages saved in Sent Box. b. Un-sent: shows text message or multimedia message not sent but saved only. Other functions related with this option are the same as specified in Sent messages. c.
SMS Setting It is used to define a series of text message options. The options displayed on screen are as shown below; * Center Number: specifies number of message center. It is the phone number of the center for you to call in order to send or receive messages. Its service provider shall specify this number previously. * Reply path: makes the application of the center on or off as necessary to send or receive messages. * Edit Preset: edits details of messages saved in dictionary.
MMS Setting It is used to define a series of options for multimedia message. The options displayed on screen are as shown below; * Valid period: Maximum period can be specified as necessary to make message sent. If once the period is over, the message will be automatically deleted. 1 hour, 12 hours, 24 hours, 72 hours, 1 week and the maximum are available for the period. The maximum has been previously established by its service provider. However, the minimum is 1 hour as described above.
multimedia message server. In other words, it means the computer which sends multimedia message (MMS) sent or received by user. MMS Profile: This option is used to make MMS information transfer function active. Select desired information and press option button. And press Details Button to show details of the information described above. Use Modify option to edit information. * Rename: changes the name of information.
* Password: means password to be used (default is WAPTM). * Gateway Address: shows IP address of gateway. Default is 192.168.80.21. Contact service provider for further information. * Connection type: displays connection type (connection oriented, secured connection oriented, connection less, secured connection less) * Homepage URL: lets user go to URL address of wap.Movistar.com as specified previously. * DNS address: shows IP address of DNS server.
CB Message Group message means a text message which will be sent to all the members who have joined the communication company. (Messages for common interest, ads, PR, etc., as displayed on the main menu of the phone) These messages will be sent to all the phones located in designated places with the applicable channel setting. Note: Select the following option on main screen to go to its sub-menu. Message/ Settings/ CB Message * Reception: allows you to receive group messages if this option is selected.
In order to use a previous option, select the option and press OK button. * CB LBT: shows group messages recently received, not saved nor deleted on this screen. If there is no message, List is empty will be displayed. If there is any message, its related title will be shown. Press details button for further information. To save the message press Yes button, and press No to delete.
5. Multimedia The multimedia menu has a function related with taking pictures with digital camera. Follow the procedures below to go to the multimedia menu. 1. In stand-by state, press menu button to display main menu option. 2. Select multimedia icon (first line, third option) and then press OK. The icons are as follow; A list for multimedia menu will be displayed, whose options are as follows; * Camera: operates image camera. * My picture: displays list of images taken by the built-in camera.
Take a picture ____________________________________ There are there methods to take a picture with GRUNDIG mobile. * Fast access: In stand-by state of the screen, press OK on the center of the direction button and select its icon . * Enter via main menu: On the menu screen, select multimedia option and press Enter to display the list showing camera option to select. Press Enter again.
If once the camera starts to operate, just press option button specify environmental setting related (Mode, Size, Flash, Quality) Press Option to display setting option menu as follows; to * Mode: sets camera mode as necessary (3 modes available) Normal mode: Press OK to take a normal picture. Multishot Mode: Press OK to take 9 pictures continuously. Motion mode: makes and saves a video file as necessary in phone memory.
If the camera starts to operate, the following icon will be displayed on the option below the screen (see Take a picture). * You may enter camera setting option described above. * If you want to enlarge or reduce image size, select the upper key (Enlarge image) and press OK. You can enlarge the image 5 times gradually. Pressing the upper again at the maximum zooming will lead to the minimum zooming function. The maximum zooming is available based on the size-related environment specified.
Image management Select My pictures and select the memory(internal or external) and press OK. In several seconds, the list of images taken will be displayed just like downloaded or received images. These images will be arranged in date/time sequence. On the list, select any image you want to edit and press Option to display the following menu. * Open: opens images on the phone screen.
Work on image You can work on images as you can enlarge, rotate, move or change names of images as follows; Rotate image Follow the procedures below to execute this operation. 1. In stand-by state, select icon to start camera mode. 2. Select My picture and press Enter. 3. Select an image to work on and press Option button. 4. Select Open and press Enter to display the selected image on the screen.
a. MMS: where you can send image to selected receiver using multimedia message. Press Enter to display the screen to write multimedia message on. Follow the procedures as described in Multimedia Message. b. Infrared rays: where you can send image to other device or equipment using infrared port (only if there is no reserved right to the image) Note: Video file can t be sent while attached to multimedia message orinfrared port.
MP3 Player ______________________________________ Press Ok in idle states and go to MP3 player. You can play the MP3 sound as following below. How to play the MP3 sound press List and go to option. a. Play: You can prelisten the MP3 sound before adding in MP3 play list. b. Add File: Add the MP3 sound to MP3 play list. C. Add folder: Add the MP3 sound folder to MP3 play list. d. Delete: Deletes the MP3 sound that are in the MP3 play list. e.
6. Leisure In Leisure menu, you can play and download the Games, melodies and images. - Games: Play games and download such gamesvia WAP server. - Melodies: Operate/download the melodies to use. - Images: Operate/download the images to use Games __________________________________________ * My Games: Select My Games in games menu to play the game. * Info: Information about the game. * Download: Select Download to download the game via WAP server. * Setting 1. Connection: Set the item about downloading. 2.
Images__________________________________________ * List: Shows the images which are available to use. 1. My picture: Shows the images from FDA/MMS which are located in internal/external memory. 2. Default picture: Shows the images which are located in the phone by default. * Info: Information about the image. * Download: Select Download to download the image via WAP server.
7. WAP You may have access to WAP via two routes. * In stand-by state of GRUNDIG mobile, press right option key . * In stand-by state, press menu button and with WAP option selected, press OK to display the option list as shown below; The following is available with the options displayed on this screen.
8. Calls Through this Calls menu, you can move to call Logs, voice mail and mainly used number list. 1. Press menu when the phone is in stand-by state to display options on main menu. 2. Use the direction button to select a Calls icon (second line, second menu). The icons are as follow; 3. Press OK button. The Calls option in principal menu will be displayed. * Call Logs: displays 3 types of calls; missed, received and dialed number. * Voice Mail: leaves a message to voice box of the phone called.
Call logs management _____________________________ Call lists saved in phone memory are classified into 3 types. * Missed: means that a call is received but not answered, which displays the following screen. * Received: means that a call is received and answered (to answer the call, press Answer button displayed as shown on the screen below. * Dialed numbers: means that a call is sent. The record of 3 types of the calls will be managed in the same manner.
Note: If you want to see call record in stand-by state, press Send button (blue) directly to go to sent call list. The list of calls displays phone numbers. If a number is identical to the number in the phone book, its contact name will be displayed instead of the phone number. The call record displays time and date when message is sent or received in regular order (first one on the list is the most recent record.) A new effective call is recorded on the first place of the list.
display the list of calls dialed. Select a call desired and press option button to display new menu with the following options. * Call: tries a call to the phone previously selected. * Send message: sends a message (Short or multimedia) to selected number. Its writing type is identical to the type described in . * Details: displays information of selected call on screen (see below).
Voice Mail _______________________________________ It is an automatic answering machine (run by communication company) saying Please, leave your message for me to call back when the call can not be answered or the phone is out of service area or turned off. Follow the procedures below to enter the voice box. 1. In stand-by state of GRUNDIG mobile, press menu button to display main menu option. 2. Use the direction button to select Calls icon (second line, second menu) and then press OK.
Whatever option is selected (Dial, Activate or Voice mail greetings), you may hear instructions if connected to the number you joined. And if any of those is unavailable, an error message will be displayed on screen of the phone. In case a call is made to voice box, you will see the following display; Options _________________________________________ Call logs, Voice mail and Useful number has the identical options as shown below.
Call settings Select call option on option menu and press Enter (check previous procedures to know how to reach here) to display the following screen: This option allows you to specify environmental setting through several special options related with call. * Any Key Answer: starts connection if active to any call when any button on the pad is pressed.
* Auto Answer: If this is selected, the call received will be automatically answered, which has 4 options (Press OK button to display those): off, 3 seconds, 5 seconds and 10 seconds. It is the duration just before the phone answers the received call automatically. * Speed Dialing: If this option is applied, you can make a fast call. Select number and then press it to make a fast call thereto in stand-by state.
8 Press option button and select Set or Delete if you want to Edit or Delete the speed dial connection. 9 Keep on pressing back Button till you reach the screen in stand-by state. If the fast dial number is presently active, keep pressing button No.7 till the call is connected. Call Services The call service includes such functions stand-by call, environmental setting and restricted display of sender. The service is available as follows; 1 In stand-by state, press menu button to display main menu option.
Call Forwarding It allows you to make received Call to go to other phone number. Select this option and press OK button to use this function, which has 4 sub-menus as follows; Voice: specifies received voice call. Data: specifies received data. Fax: specifies received fax. All: specifies all received calls. You can specify the time when you want to set the option for all the received calls (For this operation, select an option of voice, data, fax or all and press OK button).
2. Select Activate to perform Received Call on the displayed menu. In addition, select Activate to specify calls received, select Cancel to cancel and select State to know the state of call received. And then press OK. 3. Select Activate and press Enter to display the following options; a. To Voicemail: If this selected, calls will be sent to the voice box number as specified in your phone. b. To Phonebook: If this option selected, calls will be sent to the single phone saved in address book.
* All outgoing Calls: Restricts All outgoing calls, which is controlled by password. * Int l Outgoing: Restricts All outgoing calls to abord, which is controlled by password. * Int l Expect Home All Incoming: Restricts All incoming calls which is controlled by password. Inc when Roam * Cancel All: Cancel All the pre-setted restricts at a time, which is controlled by password. * Change Password: In order to change password for call barning, select change password option and press OK.
Call waiting: This service is used to make other call stand by while a precedent call is connected, which can be applied or cancelled as necessary. In order to apply this function, select Stand-by call option on call service menu (see the first of the manual if you are not familiar with the route to this screen) and press Enter to display the following options; * Apply: applies Call Waiting call option. * Cancel: cancels Call Waiting call option. * State: displays the state of Call Waiting call.
Caller ID: This will let you know the number and the name from which call is sent. In order to apply this function, select Confirm sender option on call service menu and press OK to display the following options; * Show caller: shows sender s phone number * Hide own: hides my phone number for its receiver not to see. * show connected: displays sender s number for me conveniently to check the number if dialed wrongly or correctly.
Hide own If you don t want to reveal your phone number to the phone dialed, select Hide own option and press OK. On the succeeding menu, select Cancel and press OK. Clear call Log This option is used for you to erase all the call lists through call option menu. (Missed, Received, Dialed). It will erase all the record of calls with ease. 1. In stand-by state, press menu button to display main menu option. 2. Use the direction button to select Calls icon (second line, second option) and then press OK.
* Delete all: deletes all the lists of calls saved. The procedures for each case above are identical as follows; Select desired option and press OK to display a confirming screen. Press Yes to erase or press No to cancel. Air time This provides information on calling time used in total (time used for calls dialed and received including the last one). Follow the procedures below to use this option. 1. In stand-by state, press menu button to display main menu option. 2.
3. On calls screen, select Option and press OK to go to option screen. 4. Select Air Time and press OK to display the following information. 5. Press Back button to go out of this screen. 6. Press Reset button and select desired option on the menu below to set the counter to 0 (Zero) a. All: erases all the accumulated time used for calls received and sent. b. Dialed: erases the accumulated time used for calls sent. c. Received: erases the accumulated time used for calls received. d.
1. In stand-by state, press menu button to display main menu option. 2. Select calls icon (second line, second option) and then press OK. The icons are as follow; 3. On calls screen, select Option and press OK to go to option screen. 4. Select Call costs and press OK to display the following options. a. Last call: displays the cost of the last call, which can be expressed in specific unit or currency through Display calling cost option (described later) b. All calls: displays the cost of all calls.
9. Extras The options on Extras menus allow you to connect to other functions of the phone and SIM card (My services, Calendar, Applications). Follow the procedures below to enter Extras menus. 1. In stand-by state, press menu button to display main menu option. 2. Use the direction button to select Extras menus icon (third option, second line) and then press OK.
Calendar ________________________________________ On Other menus, select Calendar and press OK to go to its related option list, where you can set an alarm for a specific event. Main options related with Calendar will be displayed as shown below; The title of the calendar screen is the date specified as seen (24-05-2005 on the previous screen). On the other hand, the number of events specified is displayed on the right side of the option line (The number of events is 0 on the previous screen).
3. Select an event type among three and press Enter (Up to 20 events can be added. And date and time of the phone are always used when a new event is added). 4. The following describes how to add text for event being specified. A text writing screen will be displayed for you to input 64 characters. After text is written, press OK button. 5. The next procedure is how to input event date (Default is the present date of the phone).
8. Set alarming time to inform you that an applicable event will be open. (Alarming time screen); None, 1 day prior, 30 minutes prior and 15 minutes prior are available, where you can select an exact time option you want. After a time option is selected, press OK. You don t need to specify details as in alarm types or birthday event. 9. Finally, specify the type of alarm to inform you that an applicable event will be open. There are 2 types of alarm available. A.
View calendar Any event once after specified can be checked everyday through the following options displayed on calendar screen; * Events: creates or changes events, which is previously described. * Scroll all days: checks events displayed on calendar everyday. If this option is selected, the option button will have names of Next and Previous. Press Next button to go to next day on calendar, where the day s specified events will be displayed. Press Previous to go to previous day on calendar.
Month view: shows the month of the present date. Other event options You can execute other operation on calendar menu. Select Event option on the displayed screen and press OK. Then, choose Select and press OK to display the event list arranged, based on specified date and its operation time (See the figure below).
* Edit: edits specific details related with event (Description, Date, start time, end time, frequency, etc.) * Delete: deletes selected event. You will be asked to press Yes to confirm). Note: Factors to be written for event are different according to its type. That is to say, all kinds of events do not have the same factors. See below; * Alarm: description, time and date. * Meeting: description, date, start time, end time, frequency, alarm type, alarm time.
Calculator ______________________________________ GRUNDIG mobile calculator helps you to perform basic calculation work. Follow the procedures below to use the calculator. 1. In stand-by state, press menu button to display main menu option. 2. Use the direction button to select Extras menus icon (third option, second line) and then press OK. The applicable icon is as shown below; 3. Select Calculator and press OK to go to Calculator screen, where you can perform calculation work.
Applications _____________________________________ On Applications menu, you can find much newer and exciting applications all available to download. Follow the procedures below to go to Applications menu. 1. In stand-by state, press menu button to display main menu option. 2. Use the direction button to select Extras menus icon and then press OK. The icons are as shown below; 3. Select Applications and press OK to go to Applications screen with the options as follow; a.
10. Settings In Settings menu, you can specify all appearances of GRUNDIG : (for bell volume of call received, calling bell melody, background screen image, other setting options of communication network, security and connection) Follow the procedures below to get to Setting menu. 1. In stand-by state, press menu button to display main menu option. 2. Use the direction button to select Settings icon (fourth option, second line) and then press OK.
Alert Type/Vol___________________________________ On Settings menu, select Alert Type/Vol option to specify bell volume of call received or other options. Note: In stand-by state of the screen, keep pressing *(asterisk) for a few seconds to change the option to manner mode, if you keep pressing *(asterisk) for a few second again in manner mode it will change to the predefined mode. 1. Volume: Sets volume from Speaker&Earpiece and Ringer for hearing or speaking. Select applicable option and press OK.
2. Tone : Set Ring tone and other sound options a. Ringer Tone : Sets melody for received call. Select this option and press OK to display My melodies (downloaded or from external memory) and Default Ring call(Boccherini ~ Maquina Escribir) and MP3 melodies. b. Message Tone : allows you to apply or cancel the sound function operated whenever the message is received(Off, Tone1 ~ Tone5) c. Slide Tone : allows you to apply or cancel the sound function operated whenever you slide up/down your cell phone. d.
3. Bell/Vib : Set the sound mode when the phone operates. a. Sound Only : Alerts(Ring) only with sound when you have a call or/and operates the phone. b. Vibrate Only : Alerts(Ring) only with vibration when you have a call or/and operates the phone. c. Sound After Vib : Alerts(Ring) with sound after the vibration when you have a call or/and operates the phone. d. Sound with Vib : Alerts(Ring) sound with vibration when you have a call or/and operates the phone. e.
Telephone ______________________________________ On Setting, select Telephone option and press OK to go to phone setting option which will show the phone screen as follows; Each option includes the following menu; Ringingtones On the Telephone screen, select melody setting option to go to List of Melodies or Download new melody.
List of Melodies On Ringingtones menu (refer to Setting phone bell for the route to this menu), select list of Melodies and press OK to display 2 options as follows. a. My melodies: Select the memory(internal or exteral) what you want to use and choose saved melody to play in the phone. b. Default Ring Call: It will display melody list included in GRUNDIG mobile. Select any melody you want to use as a phone bell and press Confirm (select the melody on the list and wait a few seconds if you want to hear it).
* Date: Select this option and press OK to edit the date on the phone. Write new date on designated form (DD/MM/YYYY if written in Spanish). With number key, write down Day (2 digits), Month (2 digits) and Year (4 digits), and press OK button to confirm the change and return to previous screen. If you want to cancel the change or return to previous screen, just press back without pressing OK.
Note: If Time is based on 12 hours system, AM or PM can be selected as necessary. Select AM or PM and press Up/Down key. * Change Time format: Select this option and press OK to edit Time form displayed on the phone, where 2 options are available. 24 hours: it is an established option, where time is displayed 00:00 to 23:59 regardless of AM or PM. If you want this option, select Option and press Confirm to return to previous screen.
The phone will choose applicable country s cell phone code (MCC) and install its applicable language. If such information is not available or there is no SIM card in the phone, Spanish will be applied for you to use. Backlight On the Telephone screen, select Setting Backlight option and press OK to display Backlight screen, where 2 options are available; Lighting (screen and key pad) and Time (duration the backlight is kept on when the phone is not operated).
Consumption On the phone screen, select Consumption and press OK to display 3 options of battery consumption; Normal, Low and Very low as described below * Normal: LED will blink every 2 seconds. * Low: LED will blink every 4 seconds. * Very low: No blink In the Low and Very low modes, 10 types of lighting are available. Dictionary On the Telephone screen, select Dictionary option and press OK to display 3 setting items. * Personal dictionary: It is used in Expected Mode when you write a message.
If you want to apply this, press OK and select On to Confirm. * 2nd language: Expected mode is also applied to the 2nd language. In case with this option executed a word is not found in main language dictionary, the word will be searched for in the 2nd language dictionary. If you want to apply or cancel this option, with the option selected press OK and choose English or Spanish as necessary or None (if 2nd language is not necessary). After then, press OK button.
* Animation: You may set animation option or may not if not necessary. Select a proper option and select on to Confirming to display the image played. Reset setting If you want to go back to initial environment after some environmental settings have been applied to the phone, simply select reset setting option and press OK to display Reset setting to default? . Select Yes or No as necessary. Note: If once the initial setting is recovered, all the saved environment information will be deleted.
* Select Mode: sets how to find communication network (Automatic, manual) * Preferred: specifies environmental setting of communication network list as desired by user. * Select Band: allows you to select frequency automatic, GSH900 / DCS1800 and PCS1900. Each option will be described later. Select Mode On Network screen, choose select mode and press OK to display select mode screen with 2 PLMN communication network options. * Auto: PLMN of desired communication network list can be selected automatically.
ROM of the phone if reserving PLMN information will display its name. Or national codes for communication network will be displayed. After such a communication network is selected, the phone will try to enter the communication network. The cell phone if registered completely will be in stand-by state. If not, the cell phone will display a list for you to search for other communication network. Preferred It helps you to define PLMN list in preferred sequence.
* Delete: deletes desired communication code from communication network list. Select communication network code to delete from the preferred. Choose its option and press Delete and Enter. Then press Yes to confirm. Select Band This option is used to set environment of the phone in order to search for communication network automatically or by hand. In case of manual mode, GSM900/DCS1800 or PCS1900 of frequency can be selected.
How to apply or cancel password Password input screen will appear whenever the phone is turned on if password has been specified. Correct password shall be input in order to use the phone (See the figure below). Note: Correct password of 4 digits shall be input.
While the PIN and PUK is input, press SOS button to connect to emergent call. In order to make password required whenever the phone is turned on, select PIN lock option and press OK to get to PIN lock screen. Select On and press OK to input password. If the message is displayed, input 4-digit password of the phone (You have 3 chances only as described) and press OK button. If password is correct, Password executed will be displayed.
4. A message will be displayed again, saying . Then input new 4-digit password again and press OK. If they are identical, your password has been changed. If they are not identical for 2 times, a message will be displayed, which means restart of the process from the beginning. Note: Password 1 and 2 are of the identical system as described above. Setting FDN environment Restricted call list is used to restrict the call only to specific phone number.
* Details: displays details of selected contact on FDN list. * New: adds new number to FDN list (you will be always asked to input password 2). * Send message: sends a message to selected number. * Call: tries to connect to selected number. * Search: uses address book to search for specific number saved in FDN list. * Delete: deletes specific phone number (you will be always asked to input password 2). * Delete all: deletes all the phone numbers saved in FDN (you will be always asked to input password 2).
SIM Lock setting screen has the following options. * On * Off Note: 3 chances are allowed for you to input correct PCK code. If all failed, PCK will be locked and you shall turn the phone off and then on. Note: If you try to turn the phone on with different SIM card while SIM is set locked, the phone will show a message . Emergency call only will be available again.
Press OK to go to the screen with the following option. * Modem: makes the infrared port active or inactive necessarily to receive instructions from other equipment (Two options are available; On and Off. The existing option specified has been through confirmation). Select On option and press OK to execute the infrared connection. After the connection is set, infrared connection icon will be displayed on the upper screen. While While data is sent, this icon will blink.
My Picture: saves applicable format of images and allows you to connect to the images saved in Image album, where you can open the image file you want to send to other user, change its name or delete. My Animation: saves applicable format of animation and allows you to connect to the animation saved in the file folder, where you can open the animation file you want to send to other user, change its name or delete.
* Details: shows details of a file saved (Number of files, Directories, size, Available Phone memory). * Open: opens a file with suitable application. For example, JPEG image files will be opened by an image viewer, and MIDI sound files by a sound player. * Rename: changes the name of a folder. * Delete: deletes a folder selected. * New Folder: makes a new file folder to save a group of files therein. * Sort: arranges files in desired sequence.
3. On the confirming screen, press Yes to finally select the connection condition. Then, press Back to return to Condition screen. Details of a specific condition are also displayed. Select Option and Details and press OK to get this information as similar as shown below. Press Previous button twice to return to Condition screen, where you can finally change the environmental setting per condition respectively. 1. Select a desired condition to change and then press OK. 2. Select Modify and press OK.
1.0 version Note: The details of this manual are regarded as correct at the moment when printed. However, Movistar reserves the right to change its details and functions without prior notice. The functions and details described in this manual may have been already modified, based on the functions of GRUNDIG mobile on which SIM card is installed or the functions of the communication network.
Exception of quality warranty This warranty will be void in the following cases; 1. In case the product is misused or used for other purposes than specified in the present safety standard of its applicable country, or any instruction described in the manual is violated. 2. This warranty dose not include normal defects unavoidable during use. 3. This warranty dose not include normal defects unavoidable on plastic, paint, key pad or antenna. 4.
Safety Information 1 . SAFETY INFORMATION FOR FIXED WIRELESS TERMINALS .POTE NTIALLY EXPLOSIVE ATMOSPHERES Turn your phone OFF when in any area with a potentially explosive atmosphere and obey all signs and instructions. Sparks in such areas could cauls e an explosion or fire resulting in bodily injury or even death. INTERFERENCE TO MEDICAL DIVICES Certain electronic equipment may be shielded against RF signal from you wireless phone.
SAR INFORMATION THIS MODEL PHONE MEETS THE GOVERNMENT’S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES. Your wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population.
U.S.A. U.S.FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT INFORMATION TO THE USER NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules.
