VTM-TLM191 VTM-TLM240 19” & 24” Professional LED Monitors with HDMI, VGA, and Looping BNC VITEK VITEK FEATURES • 19” & 24” Wide Screen LED Display Panel • HDMI, VGA, and Looping BNC Composite Video Inputs & Stereo Audio Input • Resolution up to 1920 x 1080 (1080P) • Contrast Ratio of 10,000:1 • <5ms Response time • 170° Horizontal Viewing Angle • Front Panel Controls • VESA Standard Mounting • Professional grade display designed for 24/7 continuous use in security applications with 50,000 Hour Panel Lif
Table of contents Important safety information In The Box Connections Rear interface Control Layout How to connect your monitor On-Screen Display (OSD) Operation AV Input Configuration HDMI Input Configuration VGA Input Configuration 2 4 4 4 5 5 7 7 9 12 2
IMPORTANT SAFETY INFORMATION ENVIRONMENT • • • Do not install the monitor outdoors or in any hostile environment. To prevent fire or electric shock, do not expose monitor to rain or moisture. Avoid placing the monitor in areas subject to extreme temperature such as direct sunlight or near a heating appliances/equipment (such as amplifiers, etc) as this may result in overheating and damage. This monitor is designed to be used in the office or home. Do not subject it to vibrations, dust or corrosive gases.
USING A WALL MOUNT Caution: Any wall mount must bear a minimum of 5x the monitor’s net weight to mount safely. The stand must be removed first before mounting this way. 1. Place the monitor face down on a surface that is soft, yet strong enough to hold the monitor. 2. Use a screwdriver to remove the screws from the four holes on each side of the bottom of the monitor’s base. 3. Make sure all cables are already connected to the monitor. 4.
IN THE BOX 1 x LCD Monitor, 1 x AC adapter, 1 x VGA cable, 1 x Audio cable, 1 x User Manual CONNECTIONS Rear Interface DC: Only use the 12v DC power supply included with the monitor. HDMI: (High-Definition Multimedia Interface) supports digital video and audio connections. VGA: 15 pin D-sub cable for standard VGA connection. Audio IN: 3.5 mm stereo jack connection for audio input when using VGA /AV connector.
CONTROL LAYOUT The control buttons are located on the right hand rear side of the monitor. 5keys series SOURCE - + MENU POWER 7keys series SOURCE - + ∨ ∧ MENU POWER SOURCE: Selects input mode – AV, HDMI, VGA. MENU: Access to the On Screen Display (OSD) menu. ＋ and －: POWER: Volume controls up/down, confirm input source selection and navigation in the OSD. Turns the monitor on or off. HOW TO CONNECT YOUR MONITOR 1.
If audio input is required, connect the audio (red and white) cables to the AUDIO INPUT R and L connectors on the rear of the monitor and to the Audio Output connector on the DVR/Camera etc. Connect power to the monitor and video source, and switch on. Using the SOURCE button, press repeatedly until either ‘AV1’ or ‘AV2’ (depending on the connection used) is highlighted on the display at the top of the monitor's screen, and press ‘+’ to select. 2.
BASIC ON-SCREEN DISPLAY SETUP 1. To access the OSD Menu press ‘MENU’. 2. Use the ‘＋’ or ‘－’ buttons to select the required menu item, then press the ‘SOURCE’ button to select the Sub menu. 3. Continue to use the ‘SOURCE’ button to highlight the required field, then press ‘＋’ or ‘－’ to adjust the setting. 4. Press the ‘MENU’ button to return to previous menu. 5. Press the ‘MENU’ button again to exit the OSD Menu completely. 6. N.B. To Lock or Unlock OSD settings after set up.
SHARPNESS: COLOR TEMP: PICTURE MODE: 2. OSD LANGUAGE: H-POSITION: V-POSITION: DURATION: BACKLIGHT: MEM-RECALL: 3. (0-100) Select the color temperature. (Normal/Warm/Cool) Select defaults or save user setting. ( User/Standard/Soft/Vivid) Select preferred language for OSD. (En/Ch/Ger/Fr/Sp/It/Pt/Pl/Ru) (0-100) Set the horizontal position of the OSD. (0-100) Set the vertical position of the OSD. (5-60) Set seconds for the OSD to automatically close.
4. Audio BASS: TREBLE: BALANCE: SOUND MODE: AVC: (0-100) (0-100) (-50 to +50) Set user or preset audio configurations. (User/Standard/Movie/Music) (ON/OFF) Automatic Volume Control HDMI - Input Configuration 1. Picture CONTRAST: BRIGHTNESS: (0–100) Set the difference between the light and dark areas of the picture. (0–100) Set how bright the display is.
COLOR TEMP: Select the color temperature Menu. COLOR TEMP: USER - R: USER - G: USER - B: Select color temperature preset. Set RED color level. Set GREEN color level. Set BLUE color level. 2. OSD LANGUAGE: H-POSITION: V-POSITION: DURATION: BACKLIGHT: MEM-RECALL: Select preferred language for OSD. (En/Ch/Ger/Fr/Sp/It/Pt/Pl/Ru) (0-100) Set the horizontal position of the OSD. (0-100) Set the vertical position of the OSD. (5-60) Set seconds for the OSD to automatically close.
3. Function HSTART: HSIZE: VSTART: VSIZE: 4. Set left alignment point of image. Set horizontal size of image. Set lower alignment point of image. Set vertical size of image. Audio BASS: TREBLE: BALANCE: SOUND MODE: AVC: (0-100) (0-100) (-50 to +50) Set user or preset audio configurations.
VGA - Input Configuration 1. Picture CONTRAST: BRIGHTNESS: COLOR TEMP: (0–100) Set the difference between the light and dark areas of the picture. (0–100) Set how bright the display is. Select the color temperature Menu. COLOR TEMP: USER - R: USER - G: USER - B: Select color temperature preset. Set RED color level. Set GREEN color level. Set BLUE color level.
2. OSD LANGUAGE: H-POSITION: V-POSITION: DURATION: BACKLIGHT: MEM-RECALL: 3. Select preferred language for OSD. (En/Ch/Ger/Fr/Sp/It/Pt/Pl/Ru) (0-100) Set the horizontal position of the OSD. (0-100) Set the vertical position of the OSD. (5-60) Set seconds for the OSD to automatically close. Set power level in use by backlight (HIGH/MID/LOW) Restore all factory defaults. Geometry H-POSITION: Set horizontal image position. V-POSITION: Set vertical image position.
PHASE: AUTO ADJUST: 4. bars of noise are still present, this setting can be used to remove them. If the phase of your monitor is not fine-tuned, you may observe the image being unstable in the horizontal axis. Use this option to manually correct. Perform an automatic configuration of the Phase, Clock, vertical and horizontal position. Audio BASS: TREBLE: BALANCE: SOUND MODE: AVC: (0-100) (0-100) (-50 to +50) Set user or preset audio configurations.
LIMITED PRODUCT WARRANTY VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user.
