VTC-IRE30/2810 Day/Night IR Bullet Camera with 100’ Range VITEK • High Density 1/3” Sony EX-VIEW CCD & Effio-E DSP • 700 TV Lines of Resolution • Advanced IR Optimizer helps reduce over saturation of IR illuminated video without engaging the Image Signal Processor chip • E-WDR by Adaptive Tone Reproduction • 30 850nm Infrared LEDs with up to 100’ Range • 0.003 Lux (F1.2 @ 40IRE) / 0 Lux with IR LEDs On • IR Corrected 2.
WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
1. Safety Instructions and Notes • Please read these safety and operating instructions before putting the camera into operation. • Keep the manual in a safe place for later reference. • Pay attention to safety when laying the connection cable and observe that the cable is not subjected to heavy loads, kinks, damage or moisture. • Never open the device to expose boards or lenses. The warranty becomes void if repairs are undertaken by unauthorized persons.
3. Supplied Items ① ② ③ ④ ⑤ 1 x Weatherproof D & N Bullet Camera 3 x Mounting screws 3 x anchors 1 x 2.5mm L-Wrench 1 x Installation and Operating Instructions ② ③ ④ 4. Part names 4.1 External (Below model is only used for understanding. Color or Design can be different.) ⓐ ⓑ ⓒⓓ ⓔ ⓕ ⓖ ⓗ ⓘ ⓐ ⓑ ⓒ ⓓ ⓔ ⓕ ⓖ ⓗ ⓘ ⓙ ⓙ Glass Window Sunshield Thumb screw for Sunshield Lens/IR LED Access Cover Camera Body Mount Rotation Adjustment Mount Tilt Adjustment Mount Pan Adjustment Mounting bracket Rubber gasket 4.
. Installation Instructions • Make sure the power is not applied before the installation. • Once the camera is installed, you may first connect the low voltage (AC24V or DC12V) wire to the camera power connector, then plug the AC adapter to the AC outlets to avoid an improper reset from power jitter and possible damage from voltage surge. 5.
5.2 Setup of ZOOM and FOCUS • Adjust zoom and focus in order. 1) 2) 3) 4) 5) 6) 7) Open ⓓFront cover for adjustment. Place the separated ⓓFront cover on the safe place from water & dust. Turn ⓞZoom knob counter clockwise a little to unlock the knob. Move ⓞZoom knob to fit the zoom. (Wide Tele) Turn ⓞZoom knob clockwise a little to lock the knob. Using thumb and index finger, turn ⓝFocus ring to fit the focus. (Far Close and tighten ⓓFront cover.
5.3 Sunshield Camera can be protected from the strong sun light by its own Sun shield. Sunshield must be tightened enough to the body to avoid detaching of it by the wind. When the sunshield is fixed on camera body, usually ⓒ Fix screw for Sunshield is located in center of screw hole. Adjust the sunshield back or forth according to the wide or tele position of the lens. If shades by the sunshield are seen on the image, reverse the sunshield direction backside to front. 5.
6.2 MAIN menu Follow the chart below for submenu settings. MAIN Menu-1 MAIN Menu-2 6.2.1 MAIN menu-1 MAIN menu-1 Default SHUTTER /AGC AUTO Sets the parameters related to the shutter mode and AGC for AUTO and MANUAL settings. See '6.3 SHUTTER/AGC menu' for details. LENS AUTO Selects the lens type, AUTO or MANUAL. AUTO supports DC auto-iris lens only. See '6.4 LENS menu' for details. EXT1 (w/ IR LED) DAY/NIGHT AUTO (w/o IR LED) Descriptions Can set DAY/NIGHT to AUTO, COLOR, BW, EXT1 and EXT2.
6.2.1 MAIN menu-2 MAIN menu-2 Default NR - MOTION DET OFF Sets ON/OFF for enabling/disabling MOTION DET. See '6.11 MOTION DET menu' for the parameter settings. PRIVACY OFF Sets ON/OFF for enabling/disabling PRIVACY. See '6.12 PRIVACY menu' for the parameter settings. LANGUAGE ENGLISH CAMERA ID OFF CAMERA RESET Descriptions Sets the noise reduction parameters for NR MODE and Y LEVEL, C LEVEL. See '6.10 NR menu' for details. Selects the language out of 7 languages.
6.3.1 SHUTTER/AGC>AUTO SETUP menu AUTO SETUP Default Descriptions Sets the shutter mode from AUTO IRIS or SHUT+AUTO IRIS when in MAIN>LENS>AUTO menu, but it is fixed to SHUT if in the MAIN>LENS>MANUAL menu. AU TO IR IS - Light level is controlled by an auto iris lens only. For proper auto iris operation, the auto iris operation mode in MAIN> LENS>AUTO>MODE must be set to AUTO. HIGH LUMINANCE MODE AUTO IRIS The shutter speed is fixed to the setting at MAIN>SHUTTER/AGC> MANUAL>SHUTTER in this mode.
6.3.2 SHUTTER/AGC>MANUAL SETUP menu MANUAL SETUP Default MODE SHUT +AGC Compensates the video level by the manual shutter control and AGC. SHUTTER 1/60 (1/50) Sets the manual shutter to 1/60(1/50), 1/100(1/120), 1/250,1/500,1/1000, 1/2000,1/4000 or 1/10000. Manual shutter is only useful for scenes where luminance is unchanged. AGC 6.00 Sets AGC gain in dB. Higher gain compensates brighter but noise increases. Manual AGC can be set to 6, 12, 18, 24, 30, 36, 42 or 44.8 dB. Descriptions 6.
6.5 DAY/NIGHT menu To enter DAY/NIGHT menu, press ● button at MAIN menu-1>DAY/NIGHT. DAY/NIGHT IR OPTIMIZER MODE LEVEL Default Descriptions OFF IR OPTIMIZER feature can reduce the over-saturation in video caused by the narrow emitting IR LEDs O FF – Disables IR OPTMIZER. O N – Enables IR OPTIMIZER. AUTO There are two modes available by how to manage IR OPTIMIZER. AU TO – Reducing the over-saturation is automatically adjusted along with the location of the subject.
PICT ADJUST Default Descriptions MIRROR OFF Picture will be flipped horizontally if it turns ON. BRIGHTNESS 000 Increases or decreases the brightness of the picture. This is different from that of DC iris lens and simply increases or decreases the digital gain of the video. Do not increase this too much, the dynamic range for the highlight area will decrease. CONTRAST 120 Increases or decreases the contrast of the picture. SHARPNESS 128 Increases or decreases the sharpness of the picture.
ATW Default Descriptions SPEED 250 Sets the AWB compensating speed. Lower value makes AWB faster. C AUTIO N If AWB is too fast, it may produce color oscillation. DELAY CNT 001 Adjusts the AWB compensation period to next update of AWB. The smaller value will update AWB more frequently. ATW FRAME X2.00 Determines the ATW range with respect to the fundamental range. A higher value than x1.00 will extend the ATW range at lower and higher color temperature.
6.9 BACKLIGHT menu To enter BACKLIGHT menu, press ● button in MAIN menu-1>BACKLIGHT. The Backlight Compensation – BLC – function is used to brighten an image in the foreground with a highly lit area behind it such as sunlight, limiting the affect of silhouetting.
NR Default NR MODE Y/C Selects OFF, Y, C or Y/C, which noise reduction is performed with. 006 Indicates the noise reduction strength for the luminance signal. A higher value performs a stronger noise reduction, which makes the image less sharp. Due to the limitation of 2D NR, noise reduction may not be effective enough. 004 Indicates the noise reduction strength for the chrominance signal. A higher value performs a stronger noise reduction and makes the image less sharp.
6.12 PRIVACY menu Up to 8 privacy areas are available and each area is programmable in size and location. The number of privacy areas is limited to four when MOTION DET>MONITOR AREA is ON. The privacy areas are masked with the color selected by PRIVACY>COLOR. To enter PRIVACY menu, press ● button at MAIN menu-2>PRIVACY>ON. PRIVACY AREA SEL Default Descriptions 1/8 Selects one of AREA1~AREA8 to be adjusted.
6.14 CAMERA ID menu Up to 40 characters can be input for camera ID. To enter CAMERA ID menu, press ● button at MAIN menu-2>CAMERA ID. CAMERA ID input line COMMAND LINE Use ▲,▼,◀,▶ buttons to move a block cursor over the character table and press ● button to input the selected character. To move the character input position on CAMERA ID input line, move a cursor to ←→ on COMMAND LINE and press ● button on ← or →. To clear CAMERA ID input line, move a cursor to CLR on COMMAND LINE and press ● button.
7. Specifications VTC-IRE30/2810 Image Device 1/3” High Density Sony EX-VIEW CCD & Effio-E DSP (960H) Resolution Minimum illumination 700 TV lines 0.003Lux / F1.2 (0 Lux with IR LEDs ON) Effective Pixels S/N Ratio 976(H) x 494(V) More than 52dB with AGC OFF at 50IRE Electronic Iris 1/60 to 1/100,000 sec. Infrared LEDs 30 850nm IR LEDs IR Distance Over 100 Feet Day/Night Built-In Lens Iris Mode White Balance Auto IR Corrected 2.
8.
VT-EHL 4 & 8 Channel H.264 FEATURES: • 4 or 8 Video Inputs with 1 Main, 1 Spot Monitor Output and 1 VGA output. • Real Time Recording with Up to 120 IPS at HD1 Recording / Live Display (VT-EHL4) Digital Video Recorders Simplicity and reliability is the basis upon which the EH L Digital Video Recorder was conceived. With almost every powerful feature of its predecessor the “EH”, the EHL offers an economical option for providing the most advanced recording solution available.
PROFESSIONAL LCD SERIES Full Featured Security Monitors. VTM-LCD Series 15”, 17” & 19” Professional LCD Monitors FEATURES: Vitek Professional Grade LCD Monitors are designed for constant use in a surveillance application. They combine sharp brilliant colors along with easy to use OSD functions and built in speakers, 3.5mm PC Audio and stereo RCA In/Out connections are provided for versatility and convenience.
VITEK LIMITED PRODUCT WARRANTY VITEK products carry a three (3) year limited warranty. Digital recording and storage products are also warranted for 3 years except for the hard drives which carry their own independent factory warranty from the hard drive manufacturer.
28492 Constellation Road Valencia, ca 91355 WWW.VITEKCCTV.
