Mighty Series True Day & Night Dome Cameras 700 TVL Day & Night Dome Cameras VITEK • 1/3” Sony High Density EXVIEW CCD • 700 TVL High Resolution • Sony Effio-E Digital Signal Processor • 0.0003Lux (F1.
TABLE OF CONTENTS BOX CONTENTS 1 INCLUDED ACCESSORIES 1 AVAILABLE MODELS/ACCESSORIES 2 MIGHTY DOME LAYOUT 3 INSTALLATION 4 JUNCTION BOX INSTALLATION 5 OPEN GIMBAL COVER 6 CONNECTIONS 7 LENS ADJUSTMENT 8 INFINITE AXIS GIMBAL ADJUSTMENT 9 OSD MENU FEATURES/SETUP 10 1. In the menu 10 2. MAIN menu 10 3. MAIN menu - 1 10 4. MAIN menu - 2 11 5. SHUTTER/AGC menu 11 6. SHUTTER/AGC > AUTO SETUP menu 12 7. SHUTTER/AGC > MANUAL SETUP menu 13 8. LENS menu 13 9.
TABLE OF CONTENTS 20 18. CAMERA ID menu 20 19. CAMERA RESET 21 20. EXIT 21 VITEK 17.
BOX CONTENTS 1) Dome Camera 2) Accessories 3) VT-MD-2VOC (Secondary Video Output Cable) 4) Instruction Manual & Mounting Template INCLUDED ACCESSORIES Torx Wrench - (Vandal & IR Versions Only) Type #: T20 Length: 63mm / Diameter: 4mm Qty: 1 Phillips head Screws - (Vandal & IR Versions Only) For attaching the dome cover to the flush housing.
AVAILABLE MODELS / ACCESSORIES INDOOR MIGHTY DOME CONFIGURATIONS: VTD-MP2810DN: Indoor True Day and Night Color Dome Camera with 2.8-10mm Varifocal Lens & 700TVL VTD-MP922DN: Indoor True Day and Night Color Dome Camera with 9-22mm Varifocal Lens & 700TVL VTD-MP1850DN: Indoor True Day and Night Color Dome Camera with 18-50mm Varifocal Lens & 700TVL VANDAL RESISTANT MIGHTY DOME CONFIGURATIONS: VTD-MVP2810DN: Vandal Resistant True Day and Night Color Dome Camera with 2.
MIGHTY DOME LAYOUT 1) Lens 8) Dome Cover Ring 2) Power Input Connector(12VDC / 24VAC) 9) Flush Mount Base 3) Video Output Connector - BNC 4) Camera Holder and 2nd Video output 5) Ball with the Camera Assembly 6) Safety Wire 7) Bubble 10) Surface Mount Plate 11) Assembly Screws - Torx M4x9 (Vandalproof) 12) Assembly Screws - Phillips ST4x12 (Indoor) / Phillips M4x10 (Vandalproof / IR) 13) Mounting Screws - Phillips ST4x30 3 BLACK
INSTALLATION 1) Dome Cover 1.1 Vandal Proof Domes - Use the provided Torx wrench to unscrew the vandal proof screws and remove the dome cover. 1.2 Indoor Domes - Turn the dome cover to the left to remove the dome cover. 2) Flush Mount Installation: Using four St4x30 screws, attach the flush mount base to a sturdy surface. Optional flush mount decorator plate. Model: VT-MD-FMP 3) Surface Mount Installation: Drill pilot holes at the mounting location using the provided mounting template.
JUNCTION BOX INSTALLATION Mighty Domes can easily be flush or surface mounted to an electrical junction box (4S J-Box) using the pre-drilled mounting holes on either the surface mount housing or the the flush mount base.
OPEN GIMBAL COVER To adjust the zoom and the focus, the gimbal needs to be removed temporarily from its base. 1) Remove the ball gimbal from its socket, and hold the base firmly with one hand. 2) Gently squeeze Point A and B and pull away from the base until the gimbal is removed from the base. 3) Replace the Gimbal cover by aligning the cover to the base and pressing down until it snaps back onto the base.
CONNECTIONS • Power connection: 12VDC or 24VAC dual input. • All Mighty Dome cameras come standard with a secondary video output. The secondary video cable (VT-MD-2VOC) is included in the box.
LENS ADJUSTMENT LENS ADJUSTMENT 1) Remove the Gimbal cover from the Gimbal base. 1.) Remove the Gimbal Cover from the Gimbal Base 8 2) Loosen Zoom & Focus screws and make necessary adjustments as shown. 2.) Field Loosen ZoomTelephoto(T) & Focus screws and make necessary adjustments as shown. of view: to Wide(W) Field of View: Telephoto (T) to Wide (W) Focus: Near(N) to infinity( ) Focus: Near (N) to Infinity ( ) 8 3) 3.)OSD OSDJoystick JoystickControl Control 4) 4.
INFINITE AXIS GIMBAL ADJUSTMENT Rotation and “Friction Hold” Placement The Gimbal mechanism yields maximum rotation and placement as shown below.
OSD Menu Features/Setup SETUP menu 1 In the menu Use Press , buttons to move the cursor and , buttons to change the settings. button to select or enter. button stands for MENU or ENTER button. 2 MAIN menu Follow the chart for submenu settings MAIN menu-1 MAIN menu-2 3 MAIN menu-1 MAIN menu-1 Default SHUTTER /AGC AUTO Sets the parameters related to the shutter mode and AGC for AUTO and MANUAL settings. See page 11 for ‘SHUTTER/AGC menu' details.
OSD Menu Features/Setup 4 MAIN menu-2 MAIN menu-2 Default NR - MOTION DET OFF PRIVACY OFF LANGUAGE ENGLISH CAMERA ID OFF CAMERA RESET Descriptions Sets the noise reduction parameters for NR MODE, Y LEVEL and C LEVEL. See page 18 for ‘NR menu' details. Sets ON/OFF for enabling/disabling MOTION DET. See page 19, ‘MOTION DET menu' for the parameter settings. Sets ON/OFF for enabling/disabling PRIVACY. See page 19, 'PRIVACY menu' for the parameter settings.
OSD Menu Features/Setup 6 SHUTTER/AGC>AUTO SETUP menu AUTO SETUP Default Descriptions Selects the shutter mode from AUTO IRIS or SHUT+AUTO IRIS when MAIN>LENS>AUTO but it is fixed to SHUT if MAIN>LENS>MANUAL. AUTO IRIS - Light level is controlled by an auto iris lens only. For proper auto iris operation, the auto iris operation mode in MAIN> LENS>AUTO>MODE must be set to AUTO. HIGH LUMINANCE MODE AUTO IRIS The shutter speed is fixed to the setting at MAIN>SHUTTER/AGC> MANUAL> SHUTTER in this mode.
OSD Menu Features/Setup 7 SHUTTER/AGC>MANUAL SETUP menu MANUAL SETUP Default Descriptions MODE SHUT +AGC Compensates the video level by the manual shutter control and AGC. SHUTTER 1/60 (1/50) Sets the manual shutter to 1/60(1/50), 1/100(1/120), 1/250,1/500,1/1000, 1/2000,1/4000 or 1/10000. Manual shutter is only useful when luminance is unchanged. AGC 6.00 Sets AGC gain in dB. Higher gain compensates for a brighter scene, but noise increases.
OSD Menu Features/Setup IMPORTANT ACTIVITY!!! DAY->NIGHT and NIGHT->DAY operations must be examined and verified at the final installation. Block the lens for a few seconds for NIGHT mode, then release and let it return to DAY mode. If camera stays at NIGHT mode for more than 10sec, slightly increase ‘N→D THRES’ and repeat the forementioned steps. If the scene is too dim or the lens iris was adjusted too low (near close), it may not return to DAY.
OSD Menu Features/Setup 10 PICT ADJUST menu To enter PICT ADJUST menu, press button at MAIN menu-1>PICT ADJUST. PICT ADJUST Default MIRROR OFF Picture will be flipped horizontally if it turns ON. Descriptions BRIGHTNESS 000 Increases or decreases the brightness of the picture. This is different from that of DC iris lens because it simply increases or decreases the digital gain of the video. Do not increase this too much or the dynamic range for the highlight area will decrease.
OSD Menu Features/Setup MANUAL white balance is a kind of fixed white balance which is user-programmable by B-GAIN. (R-GAIN will be automatically adjusted in accordance with B-GAIN) and useful only for the steady light. PUSH LOCK is a fixed white balance where the white balance is compensated only while the button is pressed at MAIN>WHITE BAL>PUSH LOCK and finishes the white balance when button is released. To enter ATW (MANUAL) menu, press ATW button at MAIN menu-1>WHITE BAL>ATW(MANUAL).
OSD Menu Features/Setup 12 ATR (Adaptive Tone Reproduction) menu The ATR feature improves the dynamic range and the visibility of the image by providing the optimal gradation compensation of the image in one field. This is achieved by two ways of image processing, luminance compression and contrast enhancement, so that the tone can be enhanced at highlighted and dark areas. To enter ATR menu, press ATR button at MAIN menu-1>ATR.
OSD Menu Features/Setup 13 BACKLIGHT menu To enter BACKLIGHT menu, press button at MAIN menu-1>BACKLIGHT. BLC OFF BLC ON HLC OFF HLC ON 14 NR menu To enter NR menu, press button at MAIN menu-2>NR. NR Default NR MODE Y/C Selects OFF, Y, C or Y/C which noise reduction is performed with. Descriptions Y LEVEL 006 Indicates the noise reduction strength for the luminance signal. Higher value performs stronger noise reduction and makes the image less sharp.
OSD Menu Features/Setup 15 MOTION DET menu Up to 4 motion detection areas are available and each area is programmable in size and location. The motion is displayed by means of blocks when MAIN menu-2>MOTION DET and MOTION DET>BLOCK DISP are ON. To enter MOTION DET menu, press button at MAIN menu-2>MOTION DET>ON. MOTION DET Default Descriptions DETECT SENSE 080 Adjusts the sensitivity for detecting motion. A higher value is more sensitive.
OSD Menu Features/Setup PRIVACY Default Descriptions Selects one of AREA1~AREA8 to be adjusted. AREA SEL TOP(BOTTOM) button moves up and button moves down the top (bottom) border of the selected window at AREA SEL. 1/8 LEFT(RIGHT) button moves left and button moves right the left (right) border of the selected window at AREA SEL COLOR 1 Sets one of 8 colors for the selected mask window at AREA SEL. TRANSP 1.00 Transparency rate for the mask can be adjusted. 0.
OSD Menu Features/Setup 19 CAMERA RESET Camera loads Factory defaults. To save them, go to SAVE ALL and press button.
DIMENSIONS Vandal 31 Indoor 22 BLACK
HEATER / BLOWER SPECIFICATIONS HEADER Specifications Power Supply 24 VAC Power Consumption 10W (Heater) / .
INDOOR MIGHTY DOME SPECIFICATIONS HEADER Specifications NTSC PAL Image Device 1/3” Sony High Density EXVIEW CCD Image Processor Sony Effio-E Digital Signal Processor Effective Pixels 976(H) x 494(V) Scan System Scan Frequency 976(H) x 582(V) 2:1 Interlace 59.94Hz(V), 15.734Khz(H) 50Hz(V), 15.625Khz(H) Synchronization Internal Horizontal Resolution 700TVL Sensitivity 0.0003Lux (F1.
VANDAL MIGHTY DOME SPECIFICATIONS HEADER Specifications NTSC PAL Image Device 1/3” Sony High Density EXVIEW CCD Image Processor Sony Effio-E Digital Signal Processor Effective Pixels 976(H) x 494(V) Scan System Scan Frequency 976(H) x 582(V) 2:1 Interlace 59.94Hz(V), 15.734Khz(H) 50Hz(V), 15.625Khz(H) Synchronization Internal Horizontal Resolution 700TVL Sensitivity 0.0003Lux (F1.
IR MIGHTY DOME SPECIFICATIONS HEADER Specifications NTSC PAL Image Device 1/3” Sony High Density EXVIEW CCD Image Processor Sony Effio-E Digital Signal Processor Effective Pixels 976(H) x 494(V) Scan System Scan Frequency 976(H) x 582(V) 2:1 Interlace 59.94Hz(V), 15.734Khz(H) 50Hz(V), 15.625Khz(H) Synchronization Internal Horizontal Resolution 700TVL Sensitivity 0.0003Lux (F1.
VTM-LCDP Series 15”, 17“, and 19” Professional LCD Monitors • 15”, 17“, and 19” Professional LCD Display Panels • Designed for continuous 24/7 operation • VGA, Looping BNC Composite, and S-Video Video Inputs.
CHRONO Series 8, and 16 Channel Digital Video Recorders • Highly efficient H.264 compression H.
LIMITED LIABILITY WARRANTY VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user.
