VTC-IRE40/3516 Long Range IR Bullet Camera VITEK • High Density 1/3” EX-VIEW CCD & Effio-E DSP • 700TVL High Resolution • Advanced IR Optimizer eliminates washout and dramatically reduces over saturation of IR illuminated video without engaging the Image Signal Processor chip • 40 Infrared LEDs at 850nm enable viewing in total darkness up to 150 feet • 0.003 Lux (F1.2 @ 40IRE) / 0 Lux with IR LEDs On • E-WDR by Adaptive Tone Reproduction • 3.
Table of contents 1. Safety Instructions and Notes…....................................................................................................... 2 2. General Descriptions............................................................................……………………………... 3 3. Supplied Items......................................................................................……………………………... 4 4. Part names…………………………….…...................................................…………………………... 4 5.
WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
2. General Descriptions This camera is an ultra clear resolution camera that realizes over 700TVL resolution and a crisp color reproduction with Sony 960H EX-view CCD and Effio-E image signal processor.
3. Supplied Items • 1x VTC-IRE40/3516 Long range Weatherproof IR Bullet camera • 1x Installation and Operating Instructions • 1x Mounting template • 1x ⓖ Sunshield with ⓐ Attachment thumb screw for Sunshield panel • 1x ① 3mm Hex L-wrench • 4x ② anchors • 4x ③ Wall mounting screws • 1x ④ Video Sub-output cable ① ② ③ ④ 4. Part Names 4.
4.2 Rear side view ⓛ Focus adjustment ⓚ Zoom adjustment ⓛ ⓚ 5. Installation Instructions • Make sure the power is not applied before the installation. • Once the camera is installed, you may first connect the low voltage (AC24V or DC12V) wire to the camera power connector, then plug the AC adapter to the AC outlets to avoid an improper reset from power jitter and possible damage from voltage surge. 5.1.
5.2. Power Supply Connections The VTC-IRE40/3516 can operate on either 24AC or 12VDC, dual voltage power. It is required that the polarity-matched connection is made for 12VDC supply, otherwise IR LEDs, will not operate at night. Primary and secondary grounds are completely isolated to avoid possible ground-loop problems. Clamp connectors of power input AC24V/DC12V (RED WIRE) AC24V/GND (BLACK WIRE) 5.3. Limit of pan and tilt 1. Pan limit Pan is limited to +/- 90°. 2.
3. Inclination limit (horizontal image alignment) Inclination limited to +/-90° max. 6. SETUP Menu 6.1 In the menu The Setup menu can be accessed and controlled by the OSD control joy stick on the side of the camera. Five commands are available with the joy stick. SYMBOL descriptions for joystick operation; Joy stick 1 . ▲,▼,◀,▶ - Denotes the direction of Joystick lever operation. 2 .
6.2.1 MAIN menu-1 MAIN menu-1 Default Descriptions SHUTTER /AGC AUTO LENS AUTO DAY/NIGHT EXT1 w/ IR LED AUTO w/o IR LED PICT ADJUST - WHITE BAL ATW Sets ATW, PUSH, USER1, USER2, ANTI CR, MANUAL or PUSH LOCK. See '6.7 WHITE BAL menu' for details. ATR OFF Sets ON/OFF for enabling/disabling ATR (Adaptive Tone Reproduction) compensation for the better dynamic range (E-WDR) of the image. See '6.8 ATR menu' to adjust the dynamic ranges.
6.2.1 MAIN menu-2 MAIN menu-2 Default NR - MOTION DET OFF Sets ON/OFF for enabling/disabling MOTION DET. See '6.11 MOTION DET menu' for the parameter settings. PRIVACY OFF Sets ON/OFF for enabling/disabling PRIVACY. See '6.12 PRIVACY menu' for the parameter settings. LANGUAGE ENGLISH CAMERA ID OFF CAMERA RESET Descriptions Sets the noise reduction parameters for NR MODE and Y LEVEL, C LEVEL. See '6.10 NR menu' for details. Selects the language out of 7 languages.
6.3.1 SHUTTER/AGC>AUTO SETUP menu AUTO SETUP Default Descriptions Sets the shutter mode from AUTO IRIS or SHUT+AUTO IRIS when in MAIN>LENS>AUTO menu, but it is fixed to SHUT if in the MAIN>LENS>MANUAL menu. AUTO IRIS - Light level is controlled by an auto iris lens only. For proper auto iris operation, the auto iris operation mode in MAIN> LENS>AUTO>MODE must be set to AUTO. HIGH LUMINANCE MODE AUTO IRIS The shutter speed is fixed to the setting at MAIN>SHUTTER/AGC> MANUAL>SHUTTER in this mode.
6.3.2 SHUTTER/AGC>MANUAL SETUP menu MANUAL SETUP Default MODE SHUT +AGC Compensates the video level by the manual shutter control and AGC. SHUTTER 1/60 (1/50) Sets the manual shutter to 1/60(1/50), 1/100(1/120), 1/250,1/500,1/1000, 1/2000,1/4000 or 1/10000. Manual shutter is only useful for scenes where luminance is unchanged. AGC 6.00 Sets AGC gain in dB. Higher gain compensates brighter but noise increases. Manual AGC can be set to 6, 12, 18, 24, 30, 36, 42 or 44.8 dB. Descriptions 6.
6.5 DAY/NIGHT menu To enter DAY/NIGHT menu, press ● button at MAIN menu-1>DAY/NIGHT. IMPORTANT ACTIVITY!!! DAY->NIGHT and NIGHT->DAY operations must be examined and verified at the final installation. Block the lens for a few seconds for NIGHT mode then release and let it return to DAY mode. If camera stays at NIGHT mode for more than 10sec, slightly decrease NIGHT→DAY THRES and repeat the fore-mentioned steps.
6.6 PICT ADJUST menu To enter PICT ADJUST menu, press ● button at MAIN menu-1>PICT ADJUST. PICT ADJUST Default Descriptions MIRROR OFF Picture will be flipped horizontally if it turns ON. BRIGHTNESS 000 Increases or decreases the brightness of the picture. This is different from that of DC iris lens and simply increases or decreases the digital gain of the video. Do not increase this too much, the dynamic range for the highlight area will decrease.
6.7 WHITE BAL menu White balance can be set to ATW, PUSH, USER1, USER2, ANTI CR, MANUAL or PUSH LOCK. ATW (Auto Tracking White balance) and PUSH (Full pull-in) is continuously monitoring/analyzing the color temperature of the incoming light and correcting the white balance. ATW limits the color temperature range to about 2,500˚K~8,500˚K to reduce the excessive compensation for a large object that has a single color.
MANUAL WB Default LEVEL 064 Descriptions Adjusts the manual white balance by LEVEL, (B-GAIN). 6.8 ATR (Adaptive Tone Reproduction) Menu The ATR feature improves the dynamic range and the visibility of the image by providing optimal gradation compensation of the image in one field. This is achieved by two ways of image processing, luminance compression and contrast enhancement, so that the tone can be enhanced in highlight and dark areas. To enter ATR menu, press ● button in MAIN menu-1>ATR.
6.9 BACKLIGHT menu To enter BACKLIGHT menu, press ● button in MAIN menu-1>BACKLIGHT. The Backlight Compensation – BLC – function is used to brighten an image in the foreground with a highly lit area behind it such as sunlight, limiting the affect of silhouetting.
NR Default Descriptions NR MODE Y/C Selects OFF, Y, C or Y/C, which noise reduction is performed with. Y LEVEL 006 Indicates the noise reduction strength for the luminance signal. A higher value performs a stronger noise reduction, which makes the image less sharp. C LEVEL 004 Indicates the noise reduction strength for the chrominance signal. A higher value performs a stronger noise reduction and makes the image less sharp. 6.
6.12 PRIVACY menu Up to 8 privacy areas are available and each area is programmable in size and location. The number of privacy areas is limited to four when MOTION DET>MONITOR AREA is ON. The privacy areas are masked with the color selected by PRIVACY>COLOR. To enter PRIVACY menu, press ● button in MAIN menu-2>PRIVACY>ON. PRIVACY AREA SEL COLOR Default Descriptions 1/8 Selects one of AREA1~AREA8 to be adjusted.
6.14 CAMERA ID menu Up to 40 characters can be used/input for camera ID. To enter CAMERA ID menu, press ● button in MAIN menu-2>CAMERA ID. CAMERA ID input line COMMAND LINE Use ▲,▼,◀,▶ buttons to move a block cursor over the character table and press ● button to input the selected character. To move the character input position on CAMERA ID input line, move a cursor to ← → on COMMAND LINE and press ● button on ← or → .
7. Specifications VTC-IRE40/3516 Image Device 1/3” High Density Sony EX-VIEW CCD & Effio-E DSP (960H) Resolution Minimum illumination 700 TV lines 0.003Lux / F1.2 (0 Lux with IR LEDs ON) Effective Pixels S/N Ratio 976(H) x 494(V) More than 52dB with AGC OFF at 50IRE Electronic Iris 1/60 to 1/100,000 sec. Infrared LEDs 40 850nm IR LEDs IR Distance Over 150 Feet Day/Night Built-In Lens Iris Mode White Balance True Day/Night by ICR 3.
8. Dimensional Drawings 2.95” (75mm) 1.4” (35mm) 3.5” (90mm) 2.75” (70mm) 12.48” (317mm) 10.7” (270.5mm) 3.56” (90.5mm) 3.4” (86mm) 4.35” (110.
THE MIGHTY DOME The ULTRA Versatile Dome Camera Series The Mighty Series Dome cameras include models produced with the new Pixim-Powered Seawolf Wide Dynamic Range DSP and the Sony Effio Day Night DSP. The Highest resolution Analog camera line up to date offers 700 TV Lines of Resolution, up the coax OSD Control and low light capability up to 0.00008 lux. Created to meet and solve the challenges brought on by varying lighting conditions and display clear, crisp images more accurately than ever before.
VT-EHP 8 & 16 Channel Digital Video Recorders The highest recorded resolution in a Real Time Analog DVR, the EHP delivers “D1” – 704 x 480 @ 480pps maximum frames per second. All of the powerful features and applications of the EH Family can be found in the EHP plus a built in DVD/RW, Jog Shuttle for ease of playback, Individual video loop through, individual alarm inputs & outputs as well as Point-of-Sale (POS) integration and search functions.
VITEK LIMITED PRODUCT WARRANTY VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user.
492 Constellation Road Valencia, ca 91355 WWW.VITEKCCTV.
