Manual

Device Management
DVR User Manual
97
to reset the SMTP port to the default value) and then enable or disable the SSL and attaching
image. Select the username (the username list will be updated automatically according to the
email address you enter) and enter the password of the sender and then click “Apply” to save
the settings (you don’t have to enter the username and password if “Anonymous Login” is
enabled). Click “Test” to pop up a window. Enter the e-mail address of the recipient in the
window and then click the “OK” button. The e-mail address of the sender will send an e-mail
to the recipient. If the e-mail is sent successfully, it indicates that the e-mail address of the
sender is configured correctly.
Click “Edit Recipient” to go to the following interface.
Click “Add” and then enter the recipient’s e-mail address and select the schedule (if a schedule
is selected, the system will send the alarm email and the recipient will receive it only in the
selected schedule time) in the popup window. Click “Add” in
the window to add the recipient.
You can also change the recipient’s receiving schedule by clicking in the “Schedule”
column. Click to delete the recipient in the list. Click “Apply” to save the settings. Click
“Edit Sender” to go to the e-mail configuration interface of the sender.
11.1.6 UPnP Configuration
By UPnP you can access the DVR through the web client which is in WAN via router without
port mapping.
Click Start Settings Network UPnP to go to the following interface.
Make sure the router supports UPnP function and the UPnP is enabled in the router.
Set the DVR’s IP address, subnet mask and gateway and so on corresponding to the
router.
Check “Enable” in the interface as shown below and then click “Apply”.
Click “Refresh” to refresh the UPnP status. If the UPnP status were still “Invalid UPnP” after
refreshing it for many times, the port number would be wrong. Please change the mapping type
to “Manual” and then click to modify the port until the UPnP status turns to “Valid
UPnP”. Refer to the following picture. You can view the external IP address of the DVR. Enter
the external IP address pl
us port in the address bar to access the DVR such as
http://183.17.254.19:81.
Device Management
DVR User Manual
97
to reset the SMTP port to the default value) and then enable or disable the SSL and attaching
image. Select the username (the username list will be updated automatically according to the
email address you enter) and enter the password of the sender and then click “Apply” to save
the settings (you don’t have to enter the username and password if “Anonymous Login” is
enabled). Click “Test” to pop up a window. Enter the e-mail address of the recipient in the
window and then click the “OK” button. The e-mail address of the sender will send an e-mail
to the recipient. If the e-mail is sent successfully, it indicates that the e-mail address of the
sender is configured correctly.
Click “Edit Recipient” to go to the following interface.
Click “Add” and then enter the recipient’s e-mail address and select the schedule (if a schedule
is selected, the system will send the alarm email and the recipient will receive it only in the
selected schedule time) in the popup window. Click “Add” in the window
to add the recipient.
You can also change the recipient’s receiving schedule by clicking in the “Schedule”
column. Click to delete the recipient in the list. Click “Apply” to save the settings. Click
“Edit Sender” to go to the e-mail configuration interface of the sender.
11.1.6 UPnP Configuration
By UPnP you can access the DVR through the web client which is in WAN via router without
port mapping.
Click Start Settings Network UPnP to go to the following interface.
Mak
e sure the router supports UPnP function and the UPnP is enabled in the router.
Set the DVR’s IP address, subnet mask and gateway and so on corresponding to the
router.
Check “Enable” in the interface as shown below and then click “Apply”.
Click “Refresh” to refresh the UPnP status. If the UPnP status were still “Invalid UPnP” after
refreshing it for many times, the port number would be wrong. Please change the mapping type
to “Manual” and then click to modify the port un
til the UPnP status turns to “Valid
UPnP”. Refer to the following picture. You can view the external IP address of the DVR. Enter
the external IP address plus port in the address bar to access the DVR such as
http://183.17.254.19:81.