VT-IPSD102H Dual Streaming IP Server with H.264 Compression VITEK • High quality of compression algorithm (H.264/MJPEG) • H.264 + H.264 / H.
VT-IPSD102H Manual Safety Precaution Make sure to turn off the power before installing the VT-IPSD102H. Do not install under direct sunlight or in dusty areas. Make sure to use the product within the temperature and humidity that is specified. Do not operate the product in the presence of vibrations or strong magnetic fields. Do not put electrically conducting materials in the ventilation hole. Do not open the top cover of the product.
VT-IPSD102H Manual Table of Content Table of Content ...................................................................................................................................... 2 1. Introduction ......................................................................................................................................... 4 1. About User Manual ...................................................................................................................... 4 2. Feature .............
VT-IPSD102H Manual 4. Server Status Monitoring ........................................................................................................... 44 5. Network and System Diagnostics .............................................................................................. 45 6. F/W Upgrade.............................................................................................................................. 48 7. Remove Configuration and Video Monitoring .................................
VT-IPSD102H Manual 1. Introduction 1. About User Manual This user manual provides information on operating and managing the optimal video surveillance system, VT-IPSD102H. The manual includes instructions for installation, operation and configuration of VT-IPSD102H as well as how to troubleshoot. 2. Feature VT-IPSD102H is a video and audio surveillance transmission system based on IP network through LAN, ADSL/VDSL, and Wireless LAN. The VT-IPSD102H series operates as one of two modes: Encoder or Decoder.
VT-IPSD102H Manual USB - Connection to internal or external USB storage for remote access User Interface - System status display utilizing OSD (On Screen Display) - Diagnose and upgrade through dedicated program called ENVI VMS - System configuration using Internet Explorer High Reliability - Reliable embedded system - System recovery utilizing dual watch-dog functions -5-
VT-IPSD102H Manual 3.
VT-IPSD102H Manual 4.
VT-IPSD102H Manual Rear View Terminal Function POWER IN DC 12V power input SENSOR Sensor input ALARM Relay output RS-422/485 Serial port 2 (COM2) for PTZ control and etc. Support RS-422 and (COM2) RS-232 (Com1) RS-485 protocol Serial Port 1 (COM1) for PTZ control and etc.
VT-IPSD102H Manual 5. System Modes and Connections The VT-IPSD102H system operates in one of two modes: Encoder or Decoder. The VT-IPSD102H system can be connected in either a ‘1-to-1’ fashion, where one encoder is connected to one decoder, or a ‘1-to-many’ fashion, where one encoder is connected to many decoders. The following chart shows possible combinations of video, audio and serial data transmission.
VT-IPSD102H Manual 1:N Connection (Unidirection) Remote Center Site Decoder Encoder Decoder Decoder In this configuration, a site can be monitored from many remote center locations. Although up to 64 decoders can be connected to on encoder, in the real network environment, network bandwidth can limit the maximum connections. Functionally, the VMS (Video Management System) software can replace the decoder.
VT-IPSD102H Manual VMS (Video Management System) Site Remote Center Encoder VMS Site Remote Center Encoder Decoder VMS VMS SW is a Windows based remote monitoring program to access multiple encoders for real-time monitoring or control of the encoders and connected cameras. Please refer to VMS User Manual for more information on VMS.
VT-IPSD102H Manual 2. Installation 1. Connecting Video Encoder System - Connect the camera video output line to the encoder VT-IPSD102H video input port. Decoder System - Connect the monitor video input line to the decoder VT-IPSD102H video output port. 2. Connecting Audio Audio is bi-directional in any configuration regardless of the system mode. If necessary, it can be configured to be in transmit-only, receive -only or bi-directional mode.
VT-IPSD102H Manual 6. Checking Operating Once the power is supplied to the camera, it will start booting. The system will boot up to an operating mode after approximately 40-60 seconds. The green LED on the Ethernet port will flash indicating the system is ready. Software provided on the disc called ENVI VMS allows you to check the IP address and other network details of the camera.
VT-IPSD102H Manual 3. System Operation 1. LED Display Description of LEDs System status can be monitored with LEDs.
VT-IPSD102H Manual 2. Remote Video Monitoring There are two ways to view the remote video when the connections are completed between a site and center system. In order for a proper operation, an IP address must be set accordingly. Video Monitoring with Decoder System Once the encoder IP address is set in the remote IP address section of the decoder, the decoder system will connect to the encoder system and start receiving the video images.
VT-IPSD102H Manual Focus Near, Focus Far, Auto Focus Adjust the focus Sensor Input When the sensor on the VT-IPSD102H is connected and working, the light turns red. Alarm Output Alarm Output button can trigger an event directly from the Live View page. Snapshot Snapshot button saves a snapshot of the video image currently on display. Captured picture can be stored as BMP or a JPEG file. Talk Transfer audio to audio device connected to the VT-IPSD102H. 3.
VT-IPSD102H Manual 4. Remote Configuration 1. Remote Configuration The server can be configured using a web browser. Type the IP address of VT-IPSD102H in the address input area of Internet Explorer, then a live viewing screen will be displayed. Press Setup button located in the upper right area of the monitoring screen, then the server setup page will be displayed.
VT-IPSD102H Manual 2.
VT-IPSD102H Manual Board ID Network board ID of VT-IPSD102H recognized by system Start Time Latest system boot date and time Current Time Current date & time: Enter a new date and time and press Set Current Time button to update date & time. Time Zone Time zone: Select time zone of where the system is installed. Depending on the time zone, Daylight Saving Time will work automatically.
VT-IPSD102H Manual 2.
VT-IPSD102H Manual - ENCODE Input Format Select input format; Composite NTSC or PAL Resolution Selectable video compression resolution as below: NTSC: 720 x 480, 720x 240, 352 x 480, 352 x 240 PAL: 720 x 576, 720 x 288, 352 x 576, 352 x 288 Frame Rate Select video frame rate (the maximum number of frames of video images to compress). The frame rate transmitted can be affected by the network bandwidth limitations.
VT-IPSD102H Manual - DUAL ENCODE Use Dual Encode Select On to use dual encode Dual Encode Algorithm H.264 and MJPEG can be selected for secondary streaming. Maximum resolution is 720 x 480 and there are 8 steps of resolution. If MJPEG is selected, Preference supports only Quality mode. Bitrate can be set from 32~1024kbps for Dual Encode. - MOTION DETECTION Use Motion Detection Select Motion Detection function Motion Detection Area Editing Configure regions for motion detection.
VT-IPSD102H Manual Information Display System ID and/or server time can be displayed over the video window in Web View. Each item can be turn on or off and position can be configured as well. This information is displayed after the video is decompressed. Burn-in OSD Insert system ID and date/time in the compressed video. System ID and time respectively can be turned on or off in the video. And position and Font size can be selectable.
VT-IPSD102H Manual 2.3 Audio Configuration Algorithm Algorithm: Select the audio algorithm: G.711 or AAC Bit rate: Select the Bit rate between 64kbps and 128kbps when AAC is selected The sampling rate is fixed to 32KHz when AAC is selected. Note that when VT-IPSD102H is connected to a decoder, the decoder’s audio algorithm should be set identically to transmit audio properly. Mode Select audio operation mode.
VT-IPSD102H Manual 2.
VT-IPSD102H Manual IP Mode Two IP modes are supported. Depending on the selected mode, further configuration items come as follows. IP Mode Selection Description Local IP Fixed IP Fixed IP address Local Gateway IP address Gateway Local Subnet DHCP IP Subnet mask N/A ☞ Please, get IP address information from your ISP provider or network manager. DNS Set DNS server IP address. Base Port Network base port is used for communication between systems.
VT-IPSD102H Manual Address Information Tree addresses are checked by 3 ways below. (Read-only) IP Address The servers own IP address. This information is useful when the server’s IP mode is set to DHCP. Domain Name In case the server is registered with a DDNS server, the registered domain name is displayed. MAC Address Display the MAC address of the server. If the server is registered with DDNS server, the MAC address is used in DDNS registration.
VT-IPSD102H Manual 2.
VT-IPSD102H Manual Serial Port Configuration There are two serial ports, (COM1 and COM2) in VT-IPSD102H. While COM1 port is fixed to RS-232C, COM2 port can be set to RS-422 or RS-485 protocol. The serial ports can be configured as follows. Mode Bitrate Data Bits Parity Stop Bit Selection 2400, 4800, 9600, 19200, 38400, 57600, 115200 bps 5, 6, 7, 8 bits NONE, EVEN, ODD bit 1, 2 bit Each of the serial ports configurations must be same as connecting device.
VT-IPSD102H Manual 2.
VT-IPSD102H Manual The event configuration configures the actions for each event type. Local section configures the actions for events from local (self) system, and configuration activates local devices and a Remote section configures the actions for events from remote (peer) system. The following table lists the possible actions for events. Action Beep Alarm1/Alarm2 E-mail Description Outputs beep sound using the buzzer in the system Triggers alarm (relay) port Sends E-mail to the specified address.
VT-IPSD102H Manual E-mail Notification Specify the information to send E-mail as the action of an event. The address of mail (SMTP) server needs to be specified in the Server Address field, and Port specifies the port for SMTP operation (Port 25 is the default port in SMTP operation. If a different port is configured in the SMTP server, this port needs to be changed accordingly). When the server requires authentication, ID and password of an E-mail account need to be entered also.
VT-IPSD102H Manual 2.7 Preset Configuration Preset Name Move PTZ Camera to normal view Save Press Set Button Configure up to 15 preset positions. Preset function is not available on some PTZ receivers. Make sure to check if a PTZ receiver supports preset. Preset Configuration Set the PTZ Presets by following the next steps. Move cameras to desired view using PTZ control buttons. Enter Preset name. Press Set button. Once all the presets are set, press Save List button.
VT-IPSD102H Manual 2.8 User Configuration User can be registered and privilege level of a user can be specified. User configuration is allowed only to admin user. Max 16 users can be registered and each user can have one of four privileges. Privilege Admin Manager Allowed Operations All operations Remarks User id = admin All operations except for user configuration User Live viewing and PTZ control Guest Live viewing only Add User Page for adding a user comes on pressing Add button.
VT-IPSD102H Manual Delete User A user is deleted by pressing Delete button. Change Password Pressing the Modify Password button after selecting a user shows a page for changing password. If changing the admin password, the old password is checked first. Modify Privilege Level Pressing the Modify Privilege button after selecting a user shows a page for changing the privilege. It is not allowed to change the privilege level of admin user.
VT-IPSD102H Manual 3. Decoder System Once system mode is changed as decoder, Firmware version shows Dec xxxxxxx which means decoder mode. 3.
VT-IPSD102H Manual 3.2 Network Configuration Network page of Decoder has a section for specifying the remote system to connect.
VT-IPSD102H Manual Remote Address Address of the remote system to connect. Remote Channel The channel can be selected when the remote system has more than one video channels. Media Protocol Protocol used for delivery of audio and video data between remote system and Decoder. Use Streaming Server Decoder system has the settings to connect to the Encoder or IP Camera via the Streaming Server.
VT-IPSD102H Manual 3.3 Event Configuration The event configuration configures the actions for each event type. The Local section configures the actions for local events (self=Decoder) system, and configuration activates local devices and Remote sections configures the actions for events from remote (Encoder or IP Camera) system.
VT-IPSD102H Manual The following table lists the possible actions for events. Action Beep Alarm1/Alarm2 E-mail FTP Preset Description Outputs beep sound using the buzzer in the system Triggers alarm (relay) port Sends E-mail to the specified address. AVI file can be attached Upload AVI file to a specified FTP server Moves the PTZ to associated preset position Sensor1 / Sensor2 Configure the actions when the sensor 1 or 2 is activated. Multiple actions can be set for a single event.
VT-IPSD102H Manual 5. ENVI Visual Management Software (VMS) 1. ENVI Visual Management Software ENVI VMS is a program used for basic configuration, diagnostics and F/W upgrades of video servers or IP cameras. ENVI VMS provides the following features: - Finding servers on the LAN and assigning IP address - Monitoring server status: encoding/decoding, serial, sensor etc. - Diagnostic function: PING, network bandwidth measurement, video/audio output port check, serial port check - F/W upgrade 2.
VT-IPSD102H Manual Press Add button. Removal of a server A server can be removed with the following steps: Select the server to remove on Servers tab; the selected server is highlighted in blue. Select Remove Server on the Server menu. Server selection Modification of information for a server Information for a server can be modified on the dialog invoked by selecting Modify Server Info on the Server menu.
VT-IPSD102H Manual a dialog box where the IP address of the server can be changed. It is possible to change the IP address of a server which has an IP address of a different subnet. Grouping of servers When there are a large number of servers, it is convenient to manage servers in several groups. Server groups can be created and deleted by using Add Group and Remove Group on the Group menu. The Modify Group menu is used to add servers to a group or to remove servers from a group. 3.
VT-IPSD102H Manual 4. Server Status Monitoring Servers tab – General information Servers tab shows general information for a connected server: MAC address, product model, system mode (Type) F/W version and startup time. This information comes only for connected servers. Channels tab - Monitoring of video/audio channel state The Channels tab displays how the video and audio channels of the servers are working. Item Ch Conns Displays Channel no.
VT-IPSD102H Manual Item COM1-TX Displays Activity of RS-232C port COM1-RX - TX: server -> external equipment - RX: external equipment -> server COM2-TX Activity of RS-422/485 port COM2-RX - TX: server -> external equipment - RX: external equipment -> server Sensor1 States of sensor ports Sensor2 Buzzer State of buzzer Relay1 States of relay ports Relay2 5.
VT-IPSD102H Manual Ping test is useful for checking if one or more remote systems are reachable from a server. Up to 4 systems can be registered as the targets of a Ping test, which makes it possible to identify the hop (segment of network) where network failure may happen. For example, local router, remote router and remote Encoder can be pinged from a Decoder simultaneously. Network test Network Test dialog is invoked by selecting Network Test on the Tools menu.
VT-IPSD102H Manual VT-IPSD102H System Check System Check tests if H/W components are fine and displays board ID and MAC address. Video Out Check / Display Color Bar It displays color bar on video output port. This function works for Decoder or Duplex mode, and is useful for checking if video output port or external display device is normal. Audio Out Check / Play Audio Clip It plays audio clip and outputs to audio output port.
VT-IPSD102H Manual Remote rebooting of a server A server can be rebooted by selecting Reboot in the Tools menu. 6. F/W Upgrade When Update is selected on the Tools menu, the dialog for F/W upgrade appears. Select a server to upgrade (check the check box in Sel column). More than one server can be upgraded simultaneously. Select an upgrade file. Press Upgrade button. Wait until Progress is changed to Upgrade succeeded.
VT-IPSD102H Manual Caution: Don’t power-off the server while upgrade is in progress. The server may go to irrecoverable state. When the network condition is poor, the upgrade may fail. In such case, please reattempt the procedure above after the network condition is recovered. 7. Remove Configuration and Video Monitoring Video servers and IP cameras provide web-based Setup and video viewing.
VT-IPSD102H Manual Appendix A: Sensor and Alarm Port 1. Sensor Port Terminal Type * Voltage Rating: 150VAC * Current Rating: 2A * Color: Red Sensor Signal Input Type * NO Contact Signals Connection to External Device 2. Alarm Port Terminal Type * Voltage Rating: 150VAC * Current Rating: 2A Relay Type * Contact Rating: 1A 30VDC * Switching Power: Max 30W 62.
VT-IPSD102H Manual Appendix B: Serial Port 1. RS-232 Port Port Type * 3 PIN * Pin Arrangement * Pin Description Pin NO Pin Name Description 1 TX RS232 TX (Transmit) 2 RX RS232 RX (Receive) 3 GND Ground 2.
VT-IPSD102H Manual * 4 PIN * Pin Diagram * Pin Description Pin No.
VITEK LIMITED PRODUCT WARRANTY VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user.
28492 CONSTELLATION ROAD VALENCIA, CA 91355 WWW.VITEKCCTV.
