INSTRUCTIONS MVG460 & MVG460FFR
INDEX GB P. 4 - 8 I P. 9 - 13 D P. 14 - 18 F P. 19 - 23 E P. 24 - 28 CN P. 29 - 33 KO P. 34 - 38 J P. 39 - 43 RU P. 44 - 48 DISCLAIMER & INFORMATION FOR USERS P. 49 - 55 DECLARATION OF CONFORMITY & CERTIFICATIONS P.
GB Overview Secondary quick release plate safety lock Professional 3-axis gimbal designed for DSLR and mirrorless cameras, designed with function buttons and LCD touch screen.
GB Camera Control Cable Accessories Micro USB Cable x1 18650 Li-ion Battery x1 Panasonic Lumix Shutter Cable x1 USB 2.0 to Micro x1 USB 3.0 to Micro 3.0 x1 Versatile Arm x1 Tripod x1 Charger x1 Pro kit accessories Extension Rod x1 Brushless Follow Focus (FF) x1 Gimbal Remote Controller (MVGRC) x1 5 USB 2.0 to Mini x1 Multifunctional Bracket x1 USB 2.
GB 3 Positioning Lock User Guide ⚠ Read the detailed manual before using this products. Each of the three rotating axis has one positioning lock for convenient positioning and storage purposes. Be sure to unlock them before using the gimbal. TIPS (1) Please install the camera before powering on the gimbal. (2) When the battery is low, please charge the gimbal. (3) When not in use, turn off the gimbal and then remove the batteries.
GB (3) Insert the secondary quick release plate and press down. The secondary quick release plate safety lock automatically locks and locks the secondary quick release plate safety lock. (4) Install the lens support frame to ensure that the lens holder can hold the lens firmly. 5.1 Balance Adjustment of the Tilting Axis (1) a. Unlock the tilt axis positioning lock ①, place the camera lens vertically upwards, determine the camera's center of gravity. b.
GB 5.2 Balance Adjustment of the Rolling Axis 6 Power ON/OFF ⚠ a. Tighten the tilt axis positioning lock ①, release the roll axis positioning lock ②, and observe the camera tilt state. b. Loosen the cross arm lock screw ③, slide the cross arm ④ to balance the camera position. c. Tighten the cross arm lock screw ③ and tilt the camera to the left or right, if it stays stable, it means balanced. Before powering on the gimbal, need to unlock all the axis positioning lock.
GB DISCLAIMER The information contained in this document is subject to change without notice. Vitec Imaging Solutions makes no warranty and shall not be liable for any errors on information contained in this document. Any changes or modifications not expressly approved by Vitec Imaging Solutions could void the user’s authority to operate this equipment. INFORMATION FOR USERS In accordance with Article 10 of Directive 2012/19/UE of the 04/07/2012 concerning Waste Electrical and Electronic Equipment (WEEE).
CERTIFICATIONS EU Manufacturer’s name : Vitec Imaging Solutions Manufacture’s address : Via Valsugana 100, 36022 Cassola (VI), Italy Product name : GIMBAL Product code : MVG460 & MVG460FFR Simplified Declaration of Conformity GB - Hereby, “Vitec Imaging Solutions” declares that the radio equipment type “MVG460 & MVG460FFR” is in compliance with Directive 2014/53/EU and with Directive 2011/65/ CE and its amendments.
USA FCC ID: 2AQK5-GIMBAL460 2AQK5-MVGRC Declaration of conformity NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
CANADA RUSSIA – BELARUS - KAZAKHSTAN – KYRGYZSTAN - ARMENIA IC ID: 24113-GIMBAL460 24113-MVGRC IC Statements: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
а ия FCC regulatory conformance: IC regulatory conformance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device complies with CAN ICES-3 (B)/NMB-3(B). This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference.
Cod.
