Use and Care Manual

Issue Date 3/21/2021 Rev.
Vital Coat is a NxTech Holdings LLC Brand. The information contained in this Technical Data Sheet (TDS) is furnished without warranty, expressed or implied. The information contained in
this document is believed to be accurate and it is the best information available. NxTech Holdings LLC assumes no legal responsibility for the use or reliance upon this data and
SPECIFICALLY DISCLAIMS ANY LIABILITY FOR CONSEQUENTIAL DAMAGES. NxTech Holdings, LLC makes no guarantees to the accuracy of suitability this information to specific
applications. By receiving and using the products referenced herein, consumer assumes all risk and liability for all use and handling.
For optimum results, condition material to 65°F to 85°F (18°C to 29°C) at least 24 hours prior to use.
Do not alter or add any other chemical to the product. Do not dilute unless specified in the Technical Data Sheets.
XP-900 will not hide existing surface stains. Temporary darkening of some substrates may occur
Before handling, consult the Safety Data Sheet and Container Labels for physical and health hazard information.
Do not allow products to freeze in storage or during application.
It is not recommended to apply Vital Coat Sealers over other types of sealers.
Minimum surface and ambient temperature of 45°F (7°C) and rising at the time of application.
Not intended for use on surfaces that will be constantly be submerged in water.
Mix well before using.
Directions for Use
General Instructions: Before using this product read the Technical Data Sheet (TDS) and the Safety Data Sheet (SDS)
found at www.vitalcoat.com. Apply in temperatures between 40°F - 90°F (4°C – 32°C). Always tighten lid thoroughly after use.
Always perform a test application for proper penetration on each type of surface prior to full-scale application to determine suitability
and final appearance. Test using the recommended application instructions. Let area dry thoroughly before inspection.
Immediately after use, Clean tools and equipment with soap and water. Dispose of containers in accordance with local and federal
regulations.
Precautions/Limitations
Surface Preparation: Surface preparation is important. Surfaces must be structurally sound, clean and free from as much dirt, stains,
efflorescence, oil, and other contamination as much as possible. Protect people, vehicles, property, plants, and all surfaces from
exposure to the product, from splash, residue, and wind drift before application. Do not mix or add any other chemical to this product.
Ensure that surface is thoroughly dried before application. Excessive moisture inhibits sealer penetration. A small test must be
conducted prior to application. Based upon this test, the purchaser shall determine for themselves the suitability of this product for the
intended use. Allow 28 days for new concrete or masonry to cure before applying.
Application: Vital Coat Enhance and Seal can be applied by pump sprayer, sponge, brushed or rolled. For best results, using a
quality pump sprayer capable of a producing a steady pressure under 40 psi. A .1 - .2 GPM tip is recommended. Completely saturate
the surface ensuring that the entire surface is saturated. Do not let the product puddle on the surface or dry on the surface. Back roll
with a brush or a medium nap paint roller. DO NOT OVERAPPLY. Let dry for 10 to 15 minutes. If second coat is needed, apply wet-on-
wet. On highly permeable surfaces, additional coats may be necessary. On vertical applications, apply from the bottom up. Protect
surfaces from rainfall for six hours following treatment. Many surfaces need several days to develop optimum water repellency.
Immediately clean tools, equipment, and overspray with soap and warm water.
Drying: Do not touch treated surface duringdry time. Do not add water or allow water to come in contact while curing. Protect surface
from debris coming in contact with surface while drying. Allow to dry completely for approximately 24 hours before allowing heavy
traffic on the treated surface.
Clean-up
Vital Coat
2172 Arendell Way - Tallahassee, Fl. 32308
Phone: Toll Free 844-284-2858
email: [e-mail]
Visit us at www.vitalcoat.com