2 x 12 Flat Top Pergola with Canopy Model: Monterey OPTIONAL ACCESORIES • Bolt Down Bracket Kit (4 for Pergola) • Pergola Wall • Pergola Planter VER 2.0-010617 www.wearevita.
I n t r o d u c t i o n & O ve r v i e w Getting Started First off, allow us to say thank you for the investment you have made in one of our fine pergola Canopy kits. This kit is designed to be assembled and installed ideally by two people with basic carpentry knowledge and tools. Do not attempt alone, especially during the installation stage. The Canopy kit is meant to fit any of our 12 x 12 Flat top Pergola.
Monterey Pergola Materials Overview 1 2 3 4 5 6 7 8 1. Canopy (1) 10256 2. Retainer Bracket (4) 10899 3. Retainer Steel Insert - Short (2)10257 - 1 1/4” Dia. x 55 1/2” 4. Canopy Retainer (4)10258 - 1 1/2” x 1 1/2” x 66 5/8” 5. Retainer Coupler (2) 10902 6. Canopy Steel Insert - Short (2) 10259 - 1 1/4” Dia. x 46 1/2” 7. Canopy Steel Insert - Long (2) 10261 - 1 1/4” Dia. x 80” 8. Retainer Steel Insert - Long (2)* 10261 - 1 1/4” Dia. x 80” Note: Items 7 and 8 are identical.
Monterey Pergola Materials Breakdown Check Box for These Contents 1 In the event of missing or defective parts please call our customer service dept. at 1 800 282 9346 (Mon. to Fri. 8:00 AM to 5:00 PM EST). 2 1. Canopy (1) 10256 2. Retainer Bracket (4) 10899 3. Retainer Steel Insert - Short (2) 10257 - 1 1/4” Dia. x 55 1/2” 4. Canopy Retainer (4) 10258 - 1 1/2” x 1 1/2” x 66 5/8” 5. Retainer Coupler (2) 10902 6. Canopy Steel Insert - Short (2) 10259 - 1 1/4” Dia. x 46 1/2” 7.
STEP ONE Follow steps ONE through SEVEN as per the 12 x 12 Flat Top Pergola instructions. Your pergola should look like the illustration below: STEP T WO 1 Assemble Retainer Bars 1 Connect the two pipes (80” and 55½” - the longer of the two shorter ones). 2 2 Continue to assemble the retainer bar by connecting the two retainer extrusions and coupler with the pipe assembly inside as shown. 3 Fasten all the pieces together by using four of the provided screws.
STEP THREE Attach Retainer Bars 1 Fasten the retainer brackets to the post as shown. Ensure the opening of the bracket is facing the inside of the pergola. The upper inside face of the bracket will be 1” from the bottom of the rafter. Use two screws provided to fasten to post. Repeat for adjacent post. 2 From the inside of the pergola, insert the retainer bar into the opening of the brackets.
STEP FOUR Attach Canopy 1 Navigate the canopy between the retainer bar and the end rafters and over the pergola as shown. A helper would be required. 2 Attached the second set of pipe together (80” & 46½”) and insert into the opening at the end of the canopy as shown. Notes: 1. Canopy can be adjusted by first ‘pushing’ up on the one end and pulling down on the other end (or use a helper). 2. To remove canopy, simply remove the steel insert from one end and slide the canopy out. 1 2 www.wearevita.
