Project Ideas

ManualsBrandsVita ManualsGazebosNew England Arbors 10-ft W x 10-ft L x 8-ft 10-in White Plastic Freestanding Pergola with Canopy

Table Of Contents

10 x 10 Flat Top Pergola

with Canopy

A S S E M B LY G U I D E

O P T I O N A L A C C E S S O R I E S

• Arch Kit System (2 Arches)

• Privacy Fence Panel System (2 Panels & Middle Post)

• Bolt Down Bracket Kit (4 for Pergola)

Ver 2.2 10142020

Model: Malibu

www.wearevita.com

211 Campbell St

Sarnia, Ontario, Canada, N7T 2G6

Summary of content (7 pages)

PAGE 1
0 x 10 Flat Top Pergola with Canopy A S S E M B LY G U I D E Model: Malibu OPTIONAL ACCESSORIES • Arch Kit System (2 Arches) • Privacy Fence Panel System (2 Panels & Middle Post) • Bolt Down Bracket Kit (4 for Pergola) Ver 2.2 10142020 www.wearevita.
PAGE 2
I n t r o d u c t i o n & O ve r v i e w Getting Started First off, allow us to say thank you for the investment you have made in one of our fine pergola Canopy kits. This kit is designed to be assembled and installed ideally by two people with basic carpentry knowledge and tools. Do not attempt alone, especially during the installation stage. The Canopy kit is meant to fit any of our 10 x 10 Flat top Pergola.
PAGE 3
Malibu Pergola Materials Overview 1 2 3 4 5 6 7 8 9 1. Canopy (1) 2. Retainer Bracket (4) 3. Retainer Steel Insert - Short (2) 4. Canopy Retainer (4) 5. Retainer Coupler (2) 6. Canopy Steel Insert - Short (2) 7. Canopy Steel Insert - Long (2)* 8. Rafter Joiners - Plain (6) 9. Retainer Steel Insert - Long (2)* *) Note: Items 7 and 9 are identical.
PAGE 4
Malibu Pergola Materials Breakdown Check Box These Contents 2 1 In the event of missing or defective parts please call our customer service dept. at 1 800 282 9346 (Mon. to Fri. 8:00 AM to 5:00 PM EST). 1. Canopy (1) 2. Retainer Bracket (4) 3. Retainer Steel Insert - Short (2) - 31.5 in 4. Canopy Retainer (4) 5. Retainer Coupler (2) 6. Canopy Steel Insert - Short (2) - 26.5 in 7. Canopy Steel Insert - Long (2)* 8. Rafter Joiners - Plain (6) 9.
PAGE 5
STEP ONE Follow steps one to four on the 10 x10 Flat top Pergola instructions. 1 2 In step 5, use the rafter couplers that are supplied with your Canopy box. These couplers will not have the decorative trim around the outer surface to prevent the Canopy from snagging and/or tearing. Continue steps five through seven as per the 10 x 10 Flat Top Pergola instructions.
PAGE 6
STEP THREE Attach Retainer Bars 1 Fasten the retainer brackets to the post as shown. Ensure the opening of the bracket is facing the inside of the pergola. The upper inside face of the bracket will be 1” from the bottom of the rafter. Use two screws provided to fasten to post. Repeat for adjacent post. 2 From the inside of the pergola, insert the retainer bar into the opening of the brackets.
PAGE 7
STEP FOUR Attach Canopy 1 Navigate the canopy between the retainer bar and the end rafters and over the pergola as shown. A helper would be required. 2 Attached the second set of pipe together (80” & 26½”) and insert into the opening at the end of the canopy as shown. Notes: 1. Canopy can be adjusted by first ‘pushing’ up on the one end and pulling down on the other end (or use a helper). 2. To remove canopy, simply remove the steel insert from one end and slide the canopy out. 1 2 www.wearevita.