Owner`s manual

because the current hour has an "F" in the dis-
play, you may turn off the filter by removing
the "F". The filter will continue to run, howev-
er, if the heater is on.
itself off after 6 hours.
NOTE: While heating the spa, or when the spa
is not being used, keep.the air controls closed.
5) SPECIAL FEATURES
C. Changing Heater DaJs
Your spa has been preset to heat the water to
the set temperature every day of the week. If
you wish to eliminate heating on one or more
days, touch the HEATER switch once to enter
the heater set mode. While the HEATER light
is flashing, review each day of the week by
touching the UP or DOWN switches. If a par-
ticular day is set for heating, an "H" will be
displayed beside the day number. You can
remove (or add back) the "H" by touching the
HEATER switch again. If you wish to stop the
heater before the set temperature is reached,
simply remove the "H" from the current day.
A. Automatic Blower/Purge & Jets Pump
Twice each day, the blower will automatically
run for 1 minute, lOam and 8pm, to circulate
potential stale water in the water lines. This is
a normal fW1ction of the spa.
8. Freeze ProtectIon
If the TEMPERATURE IN THE PLUMBING of
the spa approaches 40 degrees, the filter and jet
pumps will automatically come on and run for
at least one minute. H this doesn't raise the tem-
pera~ enough, the heater will come on and
raise the water temperature about 10 degrees.
4) USING THE SPA
c. Ozone Generator MonItor
H your spa is equipped with an ozone genera-
tor, the actual ultraviolet light from the gener-
ator will cause the OZONE light on the display
to glow, indicating proper operation of the
generator. (DEALER INSTALLED OPllON).
A. Starting Jet 1
You can activate the first set of jets by touching
the JET 1 switch at any time. You might notice
that the FILTER light goes off whenever the
JET 1 light comes on. This is because the filter
function and the first set of jets share a com-
mon motor. Touch the JET 1 switch again to
stop the jets and return to normal filtering, or
wait 30 minutes and the jets will automatical-
ly turn themselves off.
D. Panel Lockout
H you wish to make the SELECfRON panel
child proof, you can deactivate all touch
switches by slowly depressing the UP switch,
the DOWN switch, and the UP switch again in
exact order. H you do the sequence successful-
ly, the LOCK light on the display will begin
flashing and no more switch inputs will be
accepted. You may unlock the panel by repeat-
ing the exact sequence of UP /DOWN /UP.
8. Starting Jet 2
The second set of jets is independent of any
other function and can be turned on and off at
any time by touching the JET 2 switch. These
jets will also turn themselves off after 30 min-
utes of use.
E. Overheat Protection
H a possibility of overheating is detected, the
display will show lll.I (high limit) and the
heater will be disabled. Mer the water tem-
perature cools below 104 degrees, you may
reset the heater function by holding the
HEATER switch for 5 seconds, or until the dis-
play returns to normal. H the IllLI message
returns, you should call for service.
c. Starting Blower
Your spa is equipped with a 2-speed air blow-
er. The first toud1 of the BLOWER switd1
starts the blower at its highest speed; a second
toud1 reduces the blower to low speed. Toud1
again to turn the blower off. The blower will
automatically stop after 30 minutes of use.
D. Turning on Llgld
Your spa also has an underwater light with
two levels of brightness. The first touch of the
LIGHT switch turns the light on at full bright-
ness; a second touch reduces the light to half
brightness; and a third touch turns the light
00 off. H left on, the light will automatically turn
F. Flipping Display WIndow
Hold DOWN button for 5 seconds. The dis-
play will now be able to be read from inside
the spa. To change back, hold DOWN button
for 5 seconds again.