Owner`s manual

NOTE; For best results. read each step carefully
and entirely before proceeding to the next.
takes longer than 6 hours. the filter will con.
tInue running. (Wherlever the water reaches
the set temperature and heater turns off , the
filter will rurt orle extrc:i minute to cool the heater
elemerlt.)
1)
FILL YOUR SPA
Wipe the interior of the spa with a damp, soft
cloth to remove any residue that may be on
the surface. Fill with a garden hose. As the
spa is filling check in U)e equipment access
area for any leaks. On occasion, it may be
necessary to hand tighten a union fitting that
may have come loose during transit. Also check
that the gate valves (Ill. 1 No.6) are pulled out
to the oper, position and that the hose bib is
ctosed (Ill. 1 No.9). Continue; to fill to the wa~
ter level line.
t-.1OTE: If water has not reached the set tempera-
ture level after a fiitrC:ition cyole. or after you have
llsed the spa, the filter and heater will stay auto-
matically on LJntil the set temperature has been
reached.
3) AD.JUSTINC SETTINGS (llJ. 2)
A. Changing Temperatures
Your spa has been preset to heat the wa.
ter to 102 dearees sach time the filter runs.
Touch the TE~MP switch once to display the
actual water temperature; touch again to dis"
play the set temperature. While the light is
flashing, you may decrease or increase (up to
104 degrees) the set temperature by using the
UP and DOWN switches. If the heater fs on
and you wish to turn it off. simply reduce the
set temperature belovv the actual temperatlJra.
NOTE: if your water is extremely hard, it is prefer-
able to fill the spa nalfWay with hard water and the
rest with softened water. Never tlil the spa en-
tirely with softened water.
2)
GETTING STARTED (lIl. 2)
A. Setting Timer
Touch TIME switch once to display time,
then touch switch again to enter the time set
mode. (Note that the light is flashing over the
TIME switch and the display Is showing the day
number). Use UP and DOWN switches to set
present day of week (Sunday is considered day
number 1 ). Touch TIME switch again to show
the hour, then use UP and DOWN switches to
set the current hour. Be careful to observe the
AM/PM indicator in the display window. Touch
TIME switch once again to show and set the
current minute. The display will alJtomatlcally
return to nom1al and the light will stop flashing
after 20 seconds, or when the next switch is
touched.
B- Changing FIlter Hours
Touch the FIL TEA switch once to enter the
filter hour set mode. Whlfe the FilTER light is
flashlrlg, use th& UP ah{j DOWN switches to
revleweach hour of the day. If an "P' Is dis-
played beside the hour, the filtf)r will run dur-
ing that hour each day. Use repeated touches
of the FILTER switch to add or remove the "P'
b&slde each hour. If the filter is running be.
cause the current hour has an "PO in the dis-
play. you may turn off the fitter by removing
the "P. The flJter wIll contir1ue to run, however,
if the heater is oh.
B. Starting Filters
Touch and hold the FILTER switch for 5
seconds. The FILTER iight Will then collIe on
and the display will show "F=6H", meaning that
the filter will run for 6 hours; clearing up your
tap water. Afterwards; the filter hours will be 7
am to 9 am and 4 am to 6 am each day unless
you reset the filter hours for your pa.rtictJlar
needs. If you wish to stop the filter in less than
6 hours, hold the FILTER switch again for 5
seconds or until the display shows "F=O'r, ThEt
filter will continue to run, however, if the heater
is still on.
c. Changing Heater Days
Your spa has been preset to heat the wa~
ter to the set temperature every day of the
week., If you wish to eliminate heating on one
or more cays, touch the HEATER 9witch once
to enter the heater set mods. While the
HEATER light is flashing, review each day of
the week by touching the UP or DOWN
switches. If a particular day is set for heating,
an "H" will be displayed beside the day num-
ber. You can remove (or add back) the "HOt by
touching the HEATER switch again. If you wish
to stop the heater before the s~ttemperature
;8 reached, simply remove thA "H" from the
current day.
c. Starting Heater
After the filter has run for 15 seconds, the
heater will come on and heat the v"ater until it
reaches a temperature of 102 degrees. If this
6