411L v0.5(M02) User Manual ─ 4CH DVR ─ This document contains preliminary information and subject to change without notice.
WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This symbol is intended to alert the user to the presence of unprotected “Dangerous voltage" within the product's enclosure that may be strong enough to cause a risk of electric shock. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Table of Contents CHAPTER 1 PACKING DETAIL AND INSTALLATION _____________________ 5 1-1 PACKING ____________________________________________________ 5 1-2 Hard Disk Installation _________________________________________ 6 CHAPTER 2 PANEL LOCATION ________________________________________ 8 2-1 FRONT PANEL CONTROLS ____________________________________ 8 2-2 4CH REAR PANEL CONNECTORS ______________________________ 9 CHAPTER 3 LIVE, PLAYBACK AND PTZ OPERATIONS _________________ 10 3-1 LIVE Mode_________________
CHAPTER 7 SPECIFICAITONS_______________________________________ 41 CHAPTER 8 MOBILE APPLICATION INSTALLATION AND USAGE __________ 43 8-1 Mobile Application Installation and Operation for Symbian System 43 8-1.1 Mobile Application Installation____________________________ 43 8-1.2 Mobile Application Operation_____________________________ 44 8-1.2.1 Add New Login DVR _______________________________ 44 8-1.2.2 Logging Onto the DVR _____________________________ 44 8-1.2.
CHAPTER 1 PACKING DETAIL AND INSTALLATION 1-1 PACKING 1. DVR 2. Quick Start 5. CD 3. IR Remote Control 6. SATA Cord x1 4. Batteries x2 7. Screws x4 8.
1-2 Hard Disk Installation Step 1: Take off the three screws from the bottom of the DVR as indicated in red circles in the picture below. Step 2: Open the cover follow the way the arrows indicate. Step 3: Fix the HDD to rack mount and connect SATA and the power cable as indi cated.
Step 4: Put DVR bottom up, screw to fix the HDD as indicated. Step 5: Put the cover back and put the three screws back to fix the cover in the bottom of the DVR. NOTE: The initialization of new-installed HDD is required before recording, please refer to manual “4-8UTILITY SETUP” for detail.
CHAPTER 2 PANEL LOCATION 2-1 FRONT PANEL CONTROLS ① 1 USB Port ○ ② ③ ④ ⑤ ⑥ ⑦ ⑧ Top(USB2.0) is used to plug the USB memory stick Bottom(USB1.1) is used to plug the mouse 2 LED Display- Power ○ DVR Power is on. 3 LED Display - HDD ○ Hard disk is in use. 4 LED Display - LAN ○ Connected to the internet. 5 LED Display- LOGIN ○ Remote user logged in. 6 LED Display - REC ○ DVR Recording. (or Schedule Recording and recording are on) 7 LED Display - PLAY ○ DVR Playing back.
2-2 4CH REAR PANEL CONNECTORS ① ③ ② ④ ⑤ ⑧ ⑥ ⑦ ① DC 12V Socket for a DC 12V input. ② MAIN monitor BNC port for the main monitor. ③ VIDEO IN BNC input ports for cameras, 16 in total. ④ AUDIO IN RCA input port for audio signal. ⑤ AUDIO OUT RCA output for audio signal. ⑥ NTSC／PAL Switch Switch between NTSC and PAL format. ⑦ LAN Network port. ⑧ VGA VGA port.
CHAPTER 3 LIVE, PLAYBACK AND PTZ OPERATIONS The IR remote control and mouse operate differently under each mode; this chapter describes the functions of them under three different modes: LIVE, PLAYBACK and PTZ. 3-1 LIVE Mode You can monitor all the channels, listen to audio signal and have some related operations under LIVE mode. This paragraph describes the IR remote control, mouse operation and on screen graphical icons under LIVE mode. Table 3-1.
Table 3-1.2 Graphical icons that will display after right-clicking your mouse under LIVE mode. Icon Description Resting the cursor on this icon will bring up the following three menu icons. Main menu. Search menu. Backup menu. Turn on/off recording. Playback. Resting the cursor on this icon will bring up the following five display icons. FREEZE. PIP, picture in picture ZOOM, double the screen size AUTO-sequence LOCK, activate the key lock. Full screen display. Quad display.
Table 3-1.3 Description of on screen graphical icons in LIVE mode Icon Description Recording is on Schedule Recording is on Live Audio is on Live Audio is off Motion detected on the channel Sensor triggered on the channel Video loss detected on the channel USB device detected DVD burner is detected Connected to the LAN cable.
3-2 PLAYBACK Mode Switch to PLAYBACK mode by pressing “PLAY” under the LIVE mode, the graphical icon will show up on the upper center of the screen and the operation panel ( see below picture) will show up at right lower corner of the screen. You can drag the panel by mouse to place it on any location of your screen. Table 3-2.1 Remote control functions under the PLAYBACK mode Button Description ENTER / MODE Switch to full screen, quad. MENU / Turn on/off PAUSE. PLAY Play back at normal speed.
Table 3-2.2 The mouse operation under the PLAYBACK mode.
CHAPTER 4 MAIN MENU SETUP To enter the main menu and set up DVR, log-in account and user password are required. The default password of the administrator is “123456”. Please check the “Account Setup” for related setup of other log-in users. Table 4-0.1 Some definition of virtual keyboard. Item Description Switch between capital and small letters. / Switch between numbers and letters. Press to cancel the setup, and re-choose the login account. Delete the last character. Enter to identify the password.
Table 4-0.2 The operation of remote control under the setting menu Item MENU ESC ENTER Description Switch to different options under one item Switch to different items Save setup and back to LIVE mode Back to Upper level of menu without saving Enter the menu, or display virtual keyboard PS. The initialization of new-installed HD is required before recording, please refer to “4-8 UTILITY SETUP” for detail.
4-1.1 Quality & Frame Rate Setup Note：4CH DVR will display 4 channels and 8CH DVR will display 8 channels. Item Description View Normal / View Event Select recording mode No. Check/uncheck the box enable/disable selected channel recording Select recording resolution: NTSC:360x240, 720x240, 720x480 Resolution PAL:352X288,704X288,704X576 Quality Select quality: Lowest/ Low/ Normal/ High/ Highest FPS You can setup FPS separately for each channel.
4-2.1 MOTION SETUP Item Description Alarm Duration(Seconds) When motion detect，the number of seconds continuous alarm Motion Popup Check the box to Enable/Disable popup screen function for all channels. When motion is detected in LIVE mode, the detected channel image will pop up in full screen display. 1~4 You can setup independently for each channel. Enable Check the box to Enable/Disable motion detection for each channel.
Item Description Mask Mouse Selection Switch between “select” and “deselect” for cursor-dragging function All Area Detection Select entire screen as detection area. Mask All Area Deselect entire detection area. Continue Continue setup Exit & Save Save setup and leave Exit & Discard Cancel setup and leave 4-3 SCHEDULE SETUP Except from starting recording manually, you can also setup the recording time by weeks and schedule including normal, motion detect, and sensor detect recording type.
4-3.1 Schedule Record Setup Click on the time on the left side. The setup menu will be displayed. You can have detail setup by dates, Time and event. 4-3.2 Holiday Setup Since holidays are different by different country and region, you can setup the holiday of your location accordingly.
4-4 CAMERA SETUP Item Description 1~4 You can setup independently for each channel. Mask Check the box to Enable/Disable mask function for LIVE mode Sharpness Brightness Contrast Chroma(U)/(V) Drag the bar or press ◀ ▶ to adjust Sharpness of your camera from value 1 to 255. The default value is 1. Drag the bar or press ◀ ▶ to adjust Brightness of your camera from value 1 to 255. The default value is 128. Drag the bar or press ◀ ▶ to adjust Contrast of your camera from value 1 to 255.
4-5 ACCOUNT SETUP The Account Setup menu is used to provide role-based permission independently setting for each user (maximum of 2 users) to access DVR over network. The default admin account and password is “admin” and “123456” The default password remains the same after firmware upgrade, however, it requires 8-digits for password length when you setup a new one Item Description No. Check to activate the user’s account. Username Set up username Password Set up password for each user.
4-5.2 User Picture Setup User can select picture wished to be changed to from hard drive. 4-6 NETWORKING SETUP Item Description Connect type Setup mode for network connection: (DHCP、LAN、ADSL).
4-6.1 NETWORKING SETUP There are three ways to connect to the network as followed. 4-6.1.1 DHCP When DHCP is selected, IP address will be assigned by DHCP server automatically. 4-6.1.2 LAN Select LAN for network connection, the following information is required. Item Description IP Address Enter IP address provided by ISP Subnet Mask Enter IP address of Subnet Mask provided by ISP Gateway Enter IP address of Gate way provided by ISP DNS Enter DNS address provided by ISP.
4-6.1.3 ADSL Select ADSL for network connection, the following information is required. Item Description User Name Enter user name provided by ISP Password Enter password provided by ISP 4-6.2 HTTP Setup Item Description Enable HTTP Server Check to enable HTTP server. Users can remotely access into the DVR over the network if the HTTP function is activated. Port Enter a valid port value from 1 up to 65000. The default value is 80. Auto Assign each channel with its maxima accessible fps No.
4-6.3 DDNS Setup Item Description Enable DDNS DDNS Server Enable/disable DDNS function. Enter the registered SMTP Server: ez-dns、I-DVR.NET＊ 、DYNDNS.ORG、NO-IP.ORG、3322.ORG SMTP Server Enter the completed registered SMTP Server. (Including username + Server) If the user name is h.264 and you choose i-dvr as your server, you should enter: h.264.i-dvr.net User Name Enter user name. Password Enter password. ＊ For more detailed I-DVR.NET operation instruction, please refer to appendix I. 4-6.
Item Description User Name Check the box to enable/disable E-mal Notification function. Enter to set up SMTP Server name. (Varies according to the user) Enter to set up User Name. Password Enter to set up Password. Sender E-mail Enter to set up e-mail address of receivers. Trigger Event Enter to select events to send out E-mail notifications when below circumstances happen: Motion, and Vloss (Video Loss). Receiver E-mail Enter to set up e-mail addresses for up to 10 receivers individually.
4-7.1 DISPLAY SETUP Item Description Auto-Seq Interval Set up duration time in seconds for the interval between channels under Auto-Seq mode. Show OSD Turn On / Off OSD display Show DVR Status Turn On / Off DVR illustration and record status display Show Date/Time Turn On / Off date and time display Show Channel Name Turn On / Off channel name display CRT Deflicker(only for CRT monitor) Border Color Set up the color of border in LIVE , PLAYBACK mode.（Red, Green, Blue） 4-7.
4-7.2.1 CHANGE DATE & TIME Setup date and time of DVR manually according to user’s local time. 4-7.2.2 TIME ZONE AND DAYLIGHT SAVING TIME SETUP Set up time zone and activate Daylight Saving Time function according to user’s DVR location.
4-7.2.3 INTERNET TIME SETUP Synchronize your DVR time with internet time server. Item Description Automatic Synchronization Check to enable DVR automatic synchronization function. Effective by this option selected, DVR will automatically synchronize the time upon rebooting or by every 24 hours after booting. Update Now Effectively, Date and Time show on DVR will immediately correspond with those in internet server. 4-7.3 DEVICE SETUP Item Description Key Tone Enable/Disable keystrokes.
4-8 UTILITY SETUP Item Description HDD Initialization Select to enter hard disk initialization menu. Please stop recording before entering this menu. Enter the menu, system will show all the data (model ,volume ) of HDD that installed in DVR. Check the HDD you’d like to initialize then press “Start”. HDD initialization is successful when the status shows “Succeed” USB Initialization Clean up all data on USB. Enter USB initialization and press YES to clean up all data on your USB.
4-9 DIAGNOSTIC Item Description Version The current firmware version of DVR IP The connected IP address of DVR. If disconnected from network, the screen will display” NETWORK DISCONNECT”. MAC MAC Address of DVR HDD Status No. HDD number Volume HDD Capacity Used Rate Percentage of space used on HDD. Shows HDD status. Status USING means the HDD is being used for recording now GOOD/BAD means the HDD has a known/unknown format for the DVR.
CHAPTER 5 BACKUP & SEARCH 5-1 BACKUP SETUP User can backup any segment of recorded data in a specified time frame. To do so, either a CD R/W or storage device, like USB, must be connected to the DVR. Recorded data can also backup into NB/PC through our remote access software: 「DVRemoteDesktop.exe」 and be saved in your assigned path. The format of backup file is IRF file that can be played by both “DVRemoteDesktop.exe” 、 “ifileplay.
5-2 SEARCH SETUP Item Description Event Search Event search menu Time Search Enter time search menu 34
5-2.1 EVENT SEARCH The DVR automatically records events with type, time and channel information included. If there is recording data for an event, a yellow signal will be shown on the left side of time information. Rest your cursor under the line and press “enter”, or left click your mouse to playback the recording data. P.S. Event Records will still be generated even when hard disk is not installed or the record function is not activated. However, the record can’t be viewed after selecting it.
5-2.2 TIME SEARCH TIME SEARCH can search for the specific time of recording data to playback. Press “Enter” or left click on the desired date to playback. Note that dates with recording data are marked with a red square “ □ “System will start playing back according to the date you selected. Calendar will be shown by using mouse to click on “year” and “month”. Click “date” to display recording time of that specific date with time bar.
CHAPTER 6 Rempte Software Installation and Setup 6-1 AP Software Installation and instruction AP software:「DVR Remote Desktop」can allow you to remotely access and control the DVR from PC. p.s. Operation system currently supports Windows XP SP2 and above and Window s Vista, Windows 7 Step One：Enter the IP address of DVR in IE browser Step Two: Windows as below will show up. Please enter the user name and password. Default user name and password is admin/123456.
Step Four: Run or Save our AP software. Step Five: If you choose to run the software, Start window will be shown up. Please enter information of login DVR: IP, Port, Username and Password, or choose “Play Recorded File” to open backup files in your PC.
6-2 How to do remote monitoring through IE Step One：Enter the IP address of DVR in IE browser. The address appeared in this image is only for demonstration. Actual address is depending on the setup of on-site DVR. Step Two: Windows as below will show up. Please enter the user name and password. Default user name and password is admin/123456. Other related setup about user account and password, please check “4-5 Account Setup. “ The user name and password appeared in this image is only for demonstration.
Step Four: DVR images appear. 6-3 AP Software Operation Open the file “DVRemoteDesktop.exe”; enter the information of DVR “IP address”, “Port” “Username” and “Password” and click “OK”. You should be able to login DVR successfully and start to use the software. The default username and password is 「admin/ 123456」 “DVRemoteDesktop.exe” AP software provides some extra functions for remote users. Please check Table 6-3.1 for minimum system requirements for “DVRemoteDesktop.exe” operation. Table 6-3.
CHAPTER 7 SPECIFICAITONS 1. VIDEO Input Level Display Speed Display Resolution 1.0 Vp-p±10% Composite, 75 Balanced NTSC 120fps PAL 100fps NTSC 720(H) X 480(V) PAL 704(H) X 576(V) Monitor Output 2Vp-p Composite, 75 Balanced 2. RECORDING Compression Method H.
8. BACKUP BACKUP USB Stick Video Data, Audio Network Video Data, Audio 9. SEARCHING & PLAYBACK Searching Type Event/ Time Playback speed 120 FPS 10. MULTI-REMOTE SURVEILLANCE Monitoring Environment Web/AP/CMS Max. client Supporting multi-client (3 clients accessible) 11.
CHAPTER 8 MOBILE APPLICATION INSTALLATION AND USAGE You can remotely monitor all channels of DVR through your mobile device. The required mobile application is from DVR manufacturer and it supports mobile OS for both Windows mobile 5.0 above and Symbian.
8-1.2 Mobile Application Operation After the installation, enter the Program Files menu in your mobile device to run a file called “DVRH264”. Select “Menu” at the right lower corner of your mobile screen, 4 commands, Login Add Modify and Delete, will show up. 8-1.2.1 Add New Login DVR To log into the DVR, you need to enter the logging-in DVR information. Find “Add” under the “Menu” then enter logging-in DVR’s IP address, Port number, account name and password.
8-1.2.3 Modify the Login Information of DVR You can use the “Modify” command to change the login information of DVR. The dialogue is identical to that of the “Add” command. 8-1.2.4 Delete the Login Information of DVR “Delete” command can be used to remove the DVR information if it is no longer useful. Select the DVR on the name list then choose “Delete” 8-1.3 Live Monitoring Operation This paragraph describes some operation under the LIVE monitoring mode in device.
8-1.3.1 Scroll the Image You can use the keypad on your mobile device to scroll the image if it’s oversized. Key 2 4 6 8 Action Scroll Up Scroll Left Scroll Right Scroll Down 8-1.3.2 Image Quality Setup Select “Quality” under the “Menu” There will be 5 levels for your to choose: Low、 Normal、Middle、High and Highest. 8-1.3.3 Channel Display Select “Single” under the “Menu”, there will be all channels of your DVR in list for you to choose. PS.
8-1.3.4 Size of Image The screen size of different mobile device can be different. You can select “Size” under the “Menu” to choose from “Original” or “Fit Screen” to resize the display image. Item Original Fit Screen Description The image will be shown in original size. The image will be shown to fit the screen. 8-1.3.5 Rotate the image The Live image can be displayed in normal or rotate to 90 degrees. Select “Rotate” under the “Menu” for this operation. 8-1.3.
8-2 Mobile Application Installation and Operation for Windows Mobile System There are two kinds of applications for Window Mobile OS: JPEG compression and H.264 compression. The one for H.264 compression can transfer both audio and video signal to your mobile device. System Requirement: Mobile device OS：Windows mobile system 5.0 above. Mobile device need to support internet: GPRS／3G／Wifi… etc. 8-2.
8-2.2 Mobile Application Operation After the installation, enter the Program Files menu in your mobile device to run files named “Jrviewer” and “H264Pocket”. This application allows you to remotely logon and monitor DVR. Press “OK” to bring up the operation menu, see below chart to further information. Item Function Description Enter DVR’s name, IP address, Port, Account user, Password Add Add login DVR then press “OK” ‧Choose the DVR that you’d like to log on , then press “OK” ‧ PS.
8-2.3 Operation under the LIVE monitoring. After successful logon the DVR, press “View” to bring up operation menu. You can choose the channel, resize the image, choose the quality, and turn on/off the status bar, alarm, full screen display….etc Item Function Channel 1~16 Display for CH 1~16 Status Bar Status Bar Description Choose from CH1~16 to display.
CHAPTER 9 CMS INSTALLATION AND USAGE GUIDE 9-1 CMS Installation System Requirement: ＊Intel Pentium 4 processor or equivalent. ＊Microsoft ＊Besides Windows Vista、Windows XP、Windows 2003 Server. OS and other required APs, there will be 512MB remaining memory needed or above. ＊512MB memory above.(500M requested for group DVR connection and 180M for single DVR) ＊20MB HD space. Recording and image capturing require extra space for storage.
5.”Confirm Installation” window shows. Select ‘Next’ then the installation starts. 6. Select ‘Close’ to finish installation when the “Installation Complete” window shows.
Instruction for Log-in Failure to CMS After Upgrade Log in to CMS with the default account and password after CMS upgrade. If an error message occurs as shown in the image, please follow the instruction to solve the error. Step 1: Please enter file manager to enter folder, “Windows” and then folder “Systme32” (ex:C:\Windows\System32) Step 2: Locate file, “iCMS.dat” and delete it. Step 3: Restart CMS. Log-in successfully.
9-2 CMS LOGIN AND ENVIRONMENT To enter CMS, the administrator’s user name and password are required. The defaults are ‘admin’ and ‘123456’. After successful login, the following image shows on your screen: ③ ① ② ④ ⑤ ① DVRs, Groups & Events Information about DVRs, groups and events. See “9-3 Information List” for more detail. ② PC information and control Information about local PC’s hard disk, volume, recording...etc. See “9-4 PC Information and Control” for more detail.
9-3 DVRs, Groups & Events Icon Description View list of logged in DVR／ Group. View Logs: list all the event information of DVR 9-3.1 View DVR／Group List Single left click on ‘DVR’ or ‘Group’ will expand/collapse the entire DVRs and groups list. On the DVR list, double left click on a connected DVR will show its image in main display. See “9-6.2 DVR Administration” for further information.
9-3.2 View Event Logs Under this page, all the events of a DVR can be expanded/collapsed in the order of Re mote in/Remote out, Video Loss, Motion, Sensor, Others (Power Reset, Key Lock, Key Unlock, HD Full). 9-4 Local PC Information and Control Located at the left lower corner of the screen, please see the chart below: Icon Function Description HDD info Shows the ratio of available space / HDD capacity of C:\ drive (where CMS is installed). Recording Directory Setting Recording Directory.
9-5 Main Display The main display area is where the live image of DVR is shown. You can drag to change the location of screen for each channel and turn on/off audio signal with mouse-click. 9-5.1 Audio Control In live mode, you can turn on/off the audio signal of Ch1~Ch4: 「 」Audio signal is On 「 」Audio signal is Off Turn on/off by clicking on the graphical icon, please note there can allow only one chan nel’s audio signal to be on at one time.
9-5.2 eMAP Display In Live mode, pressing will bring the e-MAP drag-down menu. If the channel has been set up to use e-MAP, the menu will show all the e-MAP titles that have been entitled to this channel; otherwise, “No eMaps” will be shown. Please check “9-6.4 eMAP administration” for setup information.
9-5.3 PTZ Control In the main display, right click on the channel will bring up PTZ control panel as below. Icon 8 direction key Description Rotate the PTZ ZOOM+：Zoom in ZOOM : Zoom out Setup the PTZ spot as pre-set N. FOCUS+ : Focus in FOCUS-：Focus out Move to pre-set N. Set PTZ Preset Goto PTZ Preset PTZ Sensitivity Setup 16 pre-set N. Move to specific pre-set N. Activate auto pre-set tour＊ Setup PTZ sensitivity＊ Setup the “start” and “end” of liner scan.＊ Activate the liner scan cruise.
9-6 Operation Bar 10 Operations to be listed as below: Table 9-6.1 description of 10 operations: Icon Description User Administration. Please see “9-6.1 User administration” DVR Administration. Please see “9-6.2 DVR Administration” Group Administration. Please see “9-6.3 Group Administration” eMap Administration. Please see “9-6.4 eMap Administration”. Remote Playback. Please see “9-6.5 Remote Play”. HDD Playback. Please see “9-6.6 HDD Play” File Playback. Please see “9-6.7 File Play” Event Playback.
9-6.1 User administration Before the CMS can be used on a PC, user accounts should be added with proper authority. Each user should also be assigned a password and optionally a description. If a user does not have certain authority assigned, he/she will not be able to operate the corresponding function on the Operation Bar. The default is none of the authority is assigned. The administrator should assign proper authority to each user. These user accounts can be deleted or edited later on.
9-6.3 Group Administration A ‘Group’ means a set of video channels from one or many DVRs, which means, user can organize channels from different DVRs to be set in a group. This function allows you to monitor and manager channels from multiple DVRs easily and flexible. Steps: 1. Add a new group and set its name and description. 2. Click ‘Select’ which will bring up a new window. 3. Check the specific channels that you’d like them to be included in the group.
9-6.4 eMap Administration If geographical locations are relevant, or if it is desired to use a picture as the background, eMap can be used for the purpose. With eMap, the background picture can be picked by the user and channels from multiple DVRs can be placed and dragged around on the picture. Steps to follow: 1. 2. 3. 4. 5. Click and a path for the picture will be prompted. Select a picture, click OK and the picture will show in the right panel.
9-6.5 Remote Play Video images recorded on a DVR can be displayed on a remote CMS. With Remote Play function, select a DVR and a display mode on top of the screen. After the recorded segments are listed below, double click on one to show its image on the right. Icon Description Start playing. Pause. Fast forward. Fast rewind.
9-6.6 HDD Playback You can directly play the recording data in the HDD that’s uninstalled from DVR by CMS. See the picture below, the left part of screen is recording data in list that’s separated by hour and the right part is main display. You can change the display modes and play files fast forward or rewind. 9-6.7 File Playback You can play the recorded .irf files by “File Play” in CMS. It allows you to change the display mode, forward or rewind the file and drag the time bar.
9-6.8 Event Playback Event recordings on the DVR can be played back in CMS. Steps to follow: 1. Select a DVR and a display mode. 2. Select a date. 3. Double click an event and play back the images on the right. Use buttons at the bottom to control the playback. 9-6.9 Snapshot Data It can display all the snapshots you’ve taken in line in “Snapshot Data”. You can review, delete or save as other files here.
9-6.10 Recording Data It can play all the recording files you’ve recorded in line in “Recording Data”. You can play or delete them here. Steps to follow: 1. Choose the recording time at upper left corner, it will be played on the main display. 2. You can choose the display mode. 3. Time bar will be shown at right lower corner, please drag the time bar to specify the recording time you’d like to play.
APPENDIX I I-DVR.NET REGISTRATION DDNS Registration on I-DVR.NET In the package of each DVR, you will find a sticker shows account information including username and password that allows users to login I-DVR.NET for registration. To register DDNS on I-DVR.NET, please follow the steps as shown. Step 1. Please open IE browser and then enter “ http://i-DVR.NET/logon.asp ” in IE browser bar. Next, “Control Panel Logo” dialog will appear.
Step 4. Enter DVR →Main Menu → Network Setup → DDNS. Activate DDNS functions and input related information. DDNS work properly when this option selected. This part of the information required and the same within the i-dvr.net Step 5.Back to the i-dvr.net, on this page by pressing "F5: Refresh", IP will be automatically updated into the DVR of the real IP location.
APPENDIX II Remote Monitoring IE ActiveX Control Installation Instruction When using IE for remote monitoring for the first time, IE ActiveX Control is needed to be downloaded. 1. When remote monitoring on IE for the first time, an alert message occurs “Install ActiveX control” on the tool bar. 2. Click at this alert message and select “Install ActiveX Control” 3. “Do you want to install this software” alert pops up.
4. After installation, IE remote monitoring image appears. 5. If message, “Your security Settings do not allow web sites to use ActiveX controls installed on your computer.” pops on when logging in, please follow the next instruction. 6.
7. Select Security →Trusted Sites → Sites 8. Enter DVR address (This address is only for demonstration. Please use the address depends on the setup of on-site DVR.) into the blanks shown in picture, and then press “add.
9. Newly added website will appear at the trusted web sites list. Press close. 10. Go back to IE window, press refresh button or F5.
