Installation Sheet

CHC 3421
ASSEMBLY & INSTALLATION GUIDE
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN.
WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT
BREAKER BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR
OBVIOUS DEFECT, DO NOT INSTALL.
ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
1. To install glass panel to each frame of lantern box, removing all metal tabs by unscrewing set screws and set aside.
Insert a glass panel into one frame and insert the second glass panel to the next frame, replace the metal tabs and
followed with set screws to secure glass panels to the frame.
2. Insert the third glass panel into the next frame, secure with metal tabs and set screws. Repeat the procedure for the
rest glass panel.
3. Screw top loop onto top threaded rod of lantern box, and tighten set screw at side of top loop until tight.
4. Attach chain to top loop by opening/closing end link of chain.
5. Provide a 1/4” IPS pipe with one end securely mounted to a beam or a structural member. The other end should
protrude through the center of the outlet box as shown.
6. Assemble the chain mounting loop, nipple, nuts and hickey to center 1/4”IPS support pipe and adjust overall length
to allow the canopy ring to hold the canopy flush to the ceiling. When the adjustments have been completed, secure
the three (3) nuts as shown.
7. Attach the chain to the loop on top of side chains. Slip the canopy ring and canopy over the upper end of the chain.
Open the end link of the chain and lift the fixture to attach to the chain mounting loop and secure the link.
8. Lace the fixture wires, ground and safety cable through the chain and loop, exiting through the side of hickey. Run the
safety cable through the top of the outlet box and secure to structural member.
CONNECTING THE WIRES:
1. At this point, connect the electrical wires as shown in the bottom Figure making sure all wire nuts are secured.
You May have to wrap the connections with electrical tape. If your outlet has a ground wire (green or bare copper)
connect fixture’s ground wire to it. Otherwise connect fixture’s ground wire directly to the junction box.
2. Tuck these wire connections neatly into the ceiling junction box.
3. Raise the screw collar and thread onto screw collar loop protruding through canopy.
4. Insert light bulbs into sockets.
5. Your installation is now complete. Return power to the junction box and test the fixture.






                

 




1. 


2. 
          

3.          




 

    

 
     

         


      

 

   
       

 
            


  

 



 
          

        
     

     

          

 

 


Fig.3


























Assembly Instruction for Hanging Lantern
Item #: CHC3421
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
Fig.1
ASSEMBLE THE FIXTURE (Fig.2)
1. To install glass panel to each frame of lantern box, removing
all metal tabs by unscrewing set screws and set aside. Insert
a glass panel into one frame and insert the second glass
panel to the next frame, replace the metal tabs and followed
with set screws to secure glass panels to the frame.
2. Insert the third glass panel into the next frame, secure with
metal tabs and set screws. Repeat the procedure for the rest
glass panel.
3. Screw top loop onto top threaded rod of lantern box, and
tighten set screw at side of top loop until tight.
4. Attach chain to top loop by opening/closing end link of chain.
HANGING THE FIXTURE (Fig.1 & 2)
IMP
ORTANT: For a safe and secure installation, this fixture
m
ust be installed by means of support that is independent of
t
he outlet box.
SUGGESTED INSTALLATION;
1. Provide a 1/4” IPS pipe with one end securely mounted to a beam or
a structural member. The other end should protrude through the
center of the outlet box as shown.
2. Assemble the chain mounting loop, nipple, nuts and hickey to
center 1/4”IPS support pipe and adjust overall length to allow the
canopy ring to hold the canopy flush to the ceiling. When the
adjustments have been completed, secure the three (3) nuts as
shown.
3. Attach the chain to the loop on top of side chains. Slip the canopy
ring and canopy over the upper end of the chain. Open the end link
of the chain and lift the fixture to attach to the chain mounting loop
and secure the link.
4. Lace the fixture wires, ground and safety cable through the chain
and loop, exiting through the side of hickey. Run the safety cable
through the top of the outlet box and secure to structural member.
CONNECTING THE WIRES (Fig.3)
1. At this point, connect the electrical wires as shown in Fig.3
making sure all wire nuts are secured. You May have to wrap the
connections with electrical tape. If your outlet has a ground wire
(green or bare copper), connect fixture’s ground wire to it.
Otherwise connect fixture’s ground wire directly to the junction
box.
2. Tuck these wire connections neatly into the ceiling junction box.
3. Raise the canopy ring and thread onto chain mounting loop
protruding through canopy.
4. Insert light bulbs Type C, maximum 60 watt into sockets.
Your installation is now complete. Return power to the
junction box and test the fixture.
Fig.3
Fig.2
(To structural member)
Safety cable
Hex Nut
Canopy ring
(Not provided)
Hex Nut
1/4" IPS(1/2" dia.) pipe
Hickey
Nipple
Canopy
Chain mounting loop
Chain(End Link)
Fixture Wires
Fixture
Ground Wire
Black or
Smooth
WIRES
FIXTURE
Bare
Green or
Copper
FIXTURE
WIRES
(Ground)
HOUSE
Bare Copper (Ground)
Green or
WIRES
HOUSE
Black
(Hot)
WIRES
WIRES
FIXTURE
Ribbed
White or
White
WIRES
(Neutral)
HOUSE