Installation Sheet

ASSEMBLY INSTRUCTIONS
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A
LICENSED ELECTRICIAN.
WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN
FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS
ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL.
ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
11. When you reach the canopy and ceiling loop, measure the wires and cut. Be
certain to leave enough to connect inside the outlet box. Strip the insulation
back on the two power supply wires about 5/8”. Twist the power supply and
ground wires together and push through the center hole in the ceiling loop.
12. Loosen the clock collar(F), let the canopy(E) slip down the chain carefully.
DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS OR SAFETY
WILL BE COMPROMISED.
13. Connect the Ground (bare) fixture wire with the ground (usually bare) wire from
your ceiling box using wire nut(A). If you house does not have ground wire,
then attach this wire to the green grounding screw inside of outlet box.
IT IS IMPERATIVE THAT THE J-BOX IN YOUR HOME BE PROPERLY
GROUNDED.
14. Connect the Neutral fixture wire with the Neutral (usually white) wire from your
ceiling box using wire nut(A).
15. Connect the Hot (smooth edge, markings, or black) fixture wire with the Hot
(usually black) wire from your outlet box using wire nut(A). Tuck these wire
connections neatly into outlet box to secure.
16. Put canopy(E) to ceiling loop, and secure with lock collar(F).
17. Install the light bulbs(not included) into sockets.
18. Installation is complete, turn on power at fuse or circuit breaker.
**Clean with a dry, soft cloth only. Do not use harsh abrasives or chemical
agents.
DRY
Robinson Large Chandelier
Item # CHC1141
CHC1139
ASSEMBLY & INSTALLATION GUIDE
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN.
WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT
BREAKER BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR
OBVIOUS DEFECT, DO NOT INSTALL.
ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
1. Install the crossbar(B) with ceiling loop(D) to outlet box by using mounting screws(C) provided.
2. Put canopy(E) to ceiling loop (D), and secure with lock collar(F).
3. Using the dimensions of the fixture as a guide, shorten the chain (G) as needed using a pair of chain pliers.
4. Take into consideration that you will use the chain end link to mount the chandelier once you have removed the excess
chain. Unscrew the threaded collar on the chain end link. Attach the chain to the ceiling loop (D). Close the threaded
collar to secure the chain.
5. Secure lamp arm (U) to lamp body (H) by screw (K).
6. Connect the positive electrode wire (usually black) from the arm with the positive electrode wire from the center of
fixture using wire nut (I) and wrap with electrical tape.
7. Connect the negative electrode (usually white) wire from the arm with the negative electrode wire from the center of
fixture using wire nut(I).
8. Attach glass bowl (L) and (O) to lamp body with metal washer (M), plastic washer (N) (P) and finial (Q).
9. Attach bobeche (R) to the arm (U) with tube (X), (T).
10. Unscrew the threaded collar on the other chain end link. Raise the fixture and attach chain end link to the top ring.
Close the threaded collar to secure the fixture body. Unwrap the wiring from the top of the fixture body. Weave
the power supply cord and the ground wire through the chain (G).
11. When you reach the canopy and ceiling loop, measure the wires and cut. Be certain to leave enough to connect inside
the outlet box. Strip the insulation back on the two power supply wires about 5/8”.
12. Twist the power supply and ground wires together and push through the center hole in the ceiling loop.
13. Loosen the clock collar(F), let the canopy(E) slip down the chain carefully.
DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS OR SAFETY WILL BE COMPROMISED.
14. Connect the Ground (bare) fixture wire with the ground (usually bare) wire from your ceiling box using wire nut(A).
If you house does not have ground wire, then attach this wire to the green grounding screw inside of outlet box.
IT IS IMPERATIVE THAT THE J-BOX IN YOUR HOME BE PROPERLY GROUNDED.