Installation Sheet
ASSEMBLY INSTRUCTIONS
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A
LICENSED ELECTRICIAN.
WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN
FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS
ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL.
ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
1. Install the crossbar(B) with ceiling loop(D) to outlet box by using mounting
screws(C) provided.
2. Put canopy(E) to ceiling loop (D), and secure with lock collar(F).
3. Using the dimensions of the fixture as a guide, shorten the chain (G) as
needed using a pair of chain pliers.
4. Take into consideration that you will use the chain end link to mount the
chandelier once you have removed the excess chain. Unscrew the threaded
collar on the chain end link. Attach the chain to the ceiling loop (D). Close the
threaded collar to secure the chain.
5. Secure lamp arm (U) to lamp body with lockwasher (J) and locknut (K).
6. Connect the positive electrode wire (usually black) from the arm with the
positive electrode wire from the center of fixture using wire nut (I) and wrap
with electrical tape.
7. Connect the negative electrode (usually white) wire from the arm with the
negative electrode wire from the center of fixture using wire nut(I).
8. Attach metal bowl (L) and glass bowl (O) to lamp body with metal washer (M), plastic
washer (N) (P) and finial (Q).
9. Attach bobeche (R) to the arm (U) with tube (X), (T).
10. Unscrew the threaded collar on the other chain end link. Raise the fixture and
attach chain end link to the top ring. Close the threaded collar to secure the
fixture body. Unwrap the wiring from the top of the fixture body. Weave the
power supply cord and the ground wire through the chain (G).
DRY
Robinson Large Chandelier
Item # CHC1141
CHC1139
ASSEMBLY & INSTALLATION GUIDE
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN.
WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT
BREAKER BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR
OBVIOUS DEFECT, DO NOT INSTALL.
ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
1. Install the crossbar(B) with ceiling loop(D) to outlet box by using mounting screws(C) provided.
2. Put canopy(E) to ceiling loop (D), and secure with lock collar(F).
3. Using the dimensions of the fixture as a guide, shorten the chain (G) as needed using a pair of chain pliers.
4. Take into consideration that you will use the chain end link to mount the chandelier once you have removed the excess
chain. Unscrew the threaded collar on the chain end link. Attach the chain to the ceiling loop (D). Close the threaded
collar to secure the chain.
5. Secure lamp arm (U) to lamp body (H) by screw (K).
6. Connect the positive electrode wire (usually black) from the arm with the positive electrode wire from the center of
fixture using wire nut (I) and wrap with electrical tape.
7. Connect the negative electrode (usually white) wire from the arm with the negative electrode wire from the center of
fixture using wire nut(I).
8. Attach glass bowl (L) and (O) to lamp body with metal washer (M), plastic washer (N) (P) and finial (Q).
9. Attach bobeche (R) to the arm (U) with tube (X), (T).
10. Unscrew the threaded collar on the other chain end link. Raise the fixture and attach chain end link to the top ring.
Close the threaded collar to secure the fixture body. Unwrap the wiring from the top of the fixture body. Weave
the power supply cord and the ground wire through the chain (G).
11. When you reach the canopy and ceiling loop, measure the wires and cut. Be certain to leave enough to connect inside
the outlet box. Strip the insulation back on the two power supply wires about 5/8”.
12. Twist the power supply and ground wires together and push through the center hole in the ceiling loop.
13. Loosen the clock collar(F), let the canopy(E) slip down the chain carefully.
DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS OR SAFETY WILL BE COMPROMISED.
14. Connect the Ground (bare) fixture wire with the ground (usually bare) wire from your ceiling box using wire nut(A).
If you house does not have ground wire, then attach this wire to the green grounding screw inside of outlet box.
IT IS IMPERATIVE THAT THE J-BOX IN YOUR HOME BE PROPERLY GROUNDED.