Specifications

House Identification
Transmitter
identification
RF System
installation
Advisories
5700 SYSTEM
The 4281 responds only to transmit-
ters set to the same House ID (01-31,
per the DIP switch tables on page 46)
as programmed in the control’s field
*24. This prevents interference from
transmitters in other nearby systems.
To make sure that a House ID is
chosen that is not in use nearby, con-
duct the Sniffer Mode test described
under TESTING THE SYSTEM.
5700 SYSTEM
Each transmitter’s assigned zone
number is DIP switch programmable in
the unit as its transmitter ID (except
wireless keypads, which are fixed at ID
00). Whenever a transmission takes
place, whether for a fault, check-in, or
low battery, the ID number is sent
along with the message to the 4281
which, in turn, relays this information to
the control, which displays the condi-
tion and zone number on the console.
The 5827BD Wireless Keypad is key-
pad programmable.
Certain IDs in the assignment range of
10-63 have the following characteris-
tics:
Transmitters set for IDs of 32-
47 will have a 3 minute lock-out be-
tween fault transmissions to conserve
battery life (normally PIR units, but
transmitters protecting frequently
used doors and windows should also
be set for IDs in this range).
Transmitters set for IDs of 48-
55 (FIRE) will transmit once every 12
seconds while the zone is faulted. This
and the next range of zone numbers
have high signal priority and their fre-
quent transmissions while faulted in-
sure retriggering of the a/arm until the
cause is removed.
Transmitters set for IDs of 56-
63 will transmit once every 3 seconds
while faulted.
Transmitter iDs of 62 and 63 are
unsupervised to allow removal of the
5701 off-premises. Signal priority is
higher than burglary.
5800 SYSTEM
If a 5827 or 5827BD Wireless Keypad
is to be used with the system, a House
ID Code (01-31) must be set in pro-
gramming field
●24 to establish proper
communication,
and the keypad
should be set to the same ID. If no
keypad is to be used, field *24 should
be 00. D/P switch setting information
for a 5827 is given on page 46. The
5827BD is keypad programmable.
5800 SYSTEM
Each transmitter input has a different ID
(identification) code, part of which in.
eludes a unique serial number perma
nently assigned to the device during
manufacture. Many transmitters have
more than one input, hence ID code
(e.g., 5801 has 4, 5803 has 3, 5816
has 2, etc.) and each input requires G
separate programming zone.
It is not necessafy to assign a transmit-
ter’s ID(s) during installation. Instead,
the control must learn or be pro-
grammed for each transmitter’s ID
code(s) during programming, in con-
junction with assigned zone number(s)
and other data. Whenever a transmis-
sion takes place, whether for a fault,
check-in, or low battery, the ID code is
sent as part of the message to the
5881. In turn, the information is relayed
to the control, which displays the con-
dition and associated zone number on
the console.
1. If the Receiver is to be mounted remotely (not in the control’s cabinet), place it
in a high, centrally located area for best reception.
2. Do not locate receiver or transmitters on or near metal objects. This will de-
crease range and/or block transmissions.
3. Do not locate receiver in an area of high RF interference (revealed by fre-
quent or prolonged lighting of the LED inthe receiver... random flicker is ok).
4. Before mounting transmitters permanently, conduct Go/No Go Tests to verify
adequate signal strength (see TEST/NG THE SYSTEM) and reorient or relo-
cate transmitters if necessaty.
–9-