Specifications

DIALER
PROGRAMMING
(*40-*50]
In Fields
’40, *41, ●42:
Enter up to the number
of digits shown.
Do not fill unused spaces.
Enter O-9,
#+1 1 for ‘*’,
#+12 for %’,
#+13 for a r)ause
w
ARMING DING
(*51)
●4O
●41
*42
*43
*45
●46
PABX ACCESS CODE (See box at left)
Enter up to 4 digits if PABX code is needed to access an outside line. If
fewer than 4 digits entered, exit by pressing X (and press 41 if entering
next field). To clear entries from field, press X40X.
PRIMARY PHONE No. (See box at left)
Enter up to 12 digits. If fewer than 12 digits entered, exit by pressing X
(and press 42 if entering next field). To clear entries from field, press
*41*.
/Vote: Back-up reporting (8 calls are made to the secondary phone
number if no kiss-off is received after 8 attempts to the primary
number) is automatic only if there is a secondary phone number.
SECONDARY PHONE No. (See box at left)
Enter up to 12 digits. If fewer than 12 digits entered, exit by pressing X
(and press 43 if entering next field). To clear entries from field, press
X42X. See Note
in field above.
SUBSCRIBER ACCOUNT. No.
Enter digits O-9, #+1 l=B, #+12=C, #+13=D, #+14=E, or #+15=F.
Enter X as the fourth digit if a 3 digit acct no. (for 3+1 dialer reporting for-
mat) is used. Enter O as the first digit of a 4-digit acct no. for nos. 0000-
0999. End field by pressing X (and press next field) if only 3 digits are
used. To clear entries from field, press X43+$.
PHONE SYSTEM SELECT
Enter 1 digit to select dialing.
If Central St
ation
Ffcvr is not o
n WATS line: O = Pulse, 1 = Tone
If Central Stat ion Rcvr Is on WATS line: 2 = Pulse, 3 = Tone
REPORT FORMAT
Determine format to be used to report to the central station. Enter 1 digit.
O=
3+1; 4+1 ADEMCO Low Speed Std. 6 = 4+2 ADEMCO Express
1 = 3+1; 4+1 Radionics Standard
7 = ADEMCO Contact ID Reporfing
2.4+2 ADEMCO Low Speed Standard
8.3+1; 4+1
ADEMCO Low Speed Expanded
3 = 4+2 Radionics Standard
9 = 3+1: 4+1 Radionics ExDanded
(Enter ~ as the 4th digit of ●43, if 3+1 dialer reporting is to be u$ed.)
*47
●48
●49
*5O
’51
] For explanation of these formats, seepage 30.
[
Notes: The maximum number of alarm and alarm restore reports during
one armed period is determined by field *92.
See field
●27, which may override this field’s selection.
SPLIT/DUAL REPORTING
Enter O to disable (Backup report only). To enable, enter 1–5.
TO PRIMARY PHONE No.
TO SECONDARY PHONE No.
1=
Alarms, Restore, Cancel Other Repotts
2 = All Reports except Open/Close, Test
Open/Close, Test
3= Alarms, Restore, Cancel
All Reports
4= All Reports except Open/Close, Test
All Reports
5=
All Reports
(Dual Reporting)
Ail Repotis
15
SECOND DIALER DELAY (BURGLARY)
Allows time for subscriber to avoid a false alarm transmission.
Enter Ofor no or 1 for yes.
PERIODIC TEST MESSAGE
Select the desired test report interval.
O= none; 1 =24 hours; 2 = weekly; 3 = monthly
Test Report Code entered in field
●64 is sent.
For UL installations, 24 hours (1) must be se/ectecf.
SESCOA/RADIONICS SELECT
O= Radionics (O-9, B-F reporting)
1 = SESCOA (O-9 only reporting)
CONFIRMATION OF ARMING DING
Enter Ofor no or 1 for yes.
If selected, ding is external sounder only and will occur at time of kissoff of
closing repott. If closing reporl is not programmed, ding will occur at end
of exit time.
-19-