USER GUIDE PowerMaster-10 G2 Fully supervised wireless alarm control system www.visonic.
PowerMaster-10/30 G2 Version 18 User's Guide Table of Contents 1. Introduction ...................................................... 3 Preface ........................................................... 3 Overview ......................................................... 3 System Features ............................................ 3 PowerMaster-10 G2 Panel Indicator and Controls .......................................................... 4 LED Indicators ................................................
Event notifications by Telephone ................. 49 Event notifications by SMS ........................... 50 Remote Control by Telephone ..................... 50 Remote Control by SMS ............................... 52 8. Special Applications and Functions ............ 53 Looking after People Left at Home ............... 53 Acknowledging “low battery” condition in Keyfobs ......................................................... 53 APPENDIX C. GLOSSARY ................................ 65 9.
INTRODUCTION 1. Introduction Preface The PowerMaster-10/30 G2 is a highly advanced wireless alarm control system produced by Visonic Ltd. Note: Make sure that you have the name and telephone number of the monitoring station your system will report to. When calling the monitoring station to ask questions, you should have access to your "ACCOUNT NUMBER" used to identify your alarm system to the monitoring station. Obtain this information from your installer and write it.
INTRODUCTION • Numerical keys serve as function keys: When the system is disarmed, the numerical keys are used also to control various system functions. A simple icon on each key identifies the task of that key. • Data retrieval: You can obtain status information, trouble information and review memorized alarm events visually (see Chapter 5). • Event log: System events are memorized in an event log that stores the most recent events, each tagged with the time and date of the event.
INTRODUCTION Control Keys No. Indication Function 7 NEXT: Advance from item to item within a given menu. 8 BACK: Move one step back within a given menu. 9 OK: Review status messages one by one and also select a displayed option. Arming Keys No. Indication Function 12 AWAY: Arming when nobody is at home 10 HOME: Arming when people remain at home.
INTRODUCTION No. Indication Function 3 Arm (Red): Lights when the system is in the armed state. 4 Chime (Green): Chime zones will chime when disturbed (see Chapter 2). 5 Trouble (Orange): Lights when the system is in a state of trouble (see Chapter 5). Control Keys No. Indication Function 7 NEXT: Advance from item to item within a given menu. 8 BACK: Move one step back within a given menu. 9 OK: Review status messages one by one and also select a displayed option. Arming Keys No.
INTRODUCTION Built-in Alarm Sounder The PowerMaster panel has a high power siren built-in that sounds in case of alarm to deter intruders and to summon help. The maximum operating time of the siren is configured by the installer according to local regulations. Continuously ON when initiated by a burglar zone or a 24-hour zone, and when a user initiates a “panic alarm”. When initiated by a fire zone (smoke is detected) ON - ON - ON - pause - ON - ON - ON - pause - ........ and so on.
INTRODUCTION Screen Saver Mode For security reasons, it is sometimes required to hide the status indication (LCD and LED display) from a potential intruder. If the Screen Saver option is enabled by the installer, then if no key is pressed for more than 30 seconds, the display will read “POWERMASTER-10 / POWERMASTER-30” and the LEDs will stop indicating any status. Pressing any key will resume the normal status display. Pressing the Fire or Emergency keys will also initiate the Fire or Emergency alarm.
OPERATING THE POWERMASTER SYSTEM 2. Operating the PowerMaster System For more information regarding terms used in this chapter, refer to APPENDIX C. GLOSSARY. Note: This manual displays PowerMaster-10 G2 panel buttons only, even when instructions refer to both panels. When an instruction refers to PowerMaster-30 G2 only, the PowerMaster-30 G2 panel buttons are displayed. Basic Arming and Disarming Following are a set of procedures for performing basic arming and disarming of the alarm system.
OPERATING THE POWERMASTER SYSTEM After disarming, different displays may appear indicating that the system is in a state of alarm MEMORY. The MEMORY message will disappear only upon rearming the system. To disarm the system, proceed as shown: PRESS RESULTING DISPLAY [Enter Code] / [Present tag] PRESENT TAG OR ENTER CODE ____ Code / Present gag READY HH:MM ARM indicator extinguishes during the disarmed state.
OPERATING THE POWERMASTER SYSTEM Arming AWAY or HOME ‘Instant’ Pressing during the exit delay will arm the system in the "Instant' mode, i.e. without an entry delay. Therefore, any detection in any zone will trigger an immediate alarm. To arm AWAY-INSTANT, proceed as follows. PRESS RESULTING DISPLAY PRESENT TAG OR ENTER CODE ____ Code ARMING AWAY ARMING INSTANT (alternating) PLEASE EXIT NOW ↓ (Exit delay) ↓ AWAY Vacate the premises ARM indicator lights during the armed state.
OPERATING THE POWERMASTER SYSTEM Forced arming “HOME” is performed in a similar manner, as follows: PRESS [Enter code] / [Present tag] RESULTING DISPLAY PRESENT TAG OR ENTER CODE ____ Code / Present tag ARMING HOME PLEASE EXIT NOW ↓ (to mute the buzzer) Go to interior zone (Exit delay) HOME ↓ HH:MM ARM indicator flashes during the armed state.
OPERATING THE POWERMASTER SYSTEM Initiating Fire Alarm1 or Emergency Alarm You can generate a fire alarm or a silent emergency alarm in disarmed & armed states, as follows: PRESS RESULTING DISPLAY FIRE ALARM OR EMERGENCY for 2 seconds Then, if or when the system is in the disarmed state: READY HH:MM (alternating) READY MEMORY To stop the alarm, press and then key in your valid user code. Note: For UL Listed product, Emergency is ancillary use only.
SPEECH AND SOUND CONTROL 3. Speech and Sound Control1 Speech & Sound Cont. Push-buttons The sound and speech-related functions offered by the control panel are controlled with the keypad, as detailed in the following list. When partitioning is enabled: Sound and speech-related features only apply to the partition(s) where the control panel is present. An activity performed via the control panel from another partition will be displayed and the LED will light.
SPEECH AND SOUND CONTROL Once the last of the boxes disappears, RECORDING ENDED will be displayed. When you release the button, the display will revert to the normal status-displaying mode, but will also indicate that a message is waiting. For example: READY HH:MM (alternating) READY MSG To check your own message, listen to it within one minute from the end of recording (see the next section Message Playback). This way the MSG indication will not be erased.
ELECTRICAL APPLIANCE CONTROL 4. Electrical Appliance Control Control Options and Pushbuttons The system allows manual or automatic remote control of a device connected to the PGM output. The user defines the ON and OFF times via the Scheduler (see Chapter 6 - B.14 Programming the Scheduler). The installer determines which zone sensors will switch the remote controlled appliances on and off.
REVIEWING TROUBLES AND ALARM MEMORY 5. Reviewing Troubles and Alarm memory Alarm & Tamper Memory Indication The PowerMaster retains in its memory alarm and “tamper” events that occurred during the last arming period. Note: Alarm events are memorized only after the “abort period” (see Appendix C). This means that if you disarm the system immediately - before the abort period expires - there will be no memory indication A.
REVIEWING TROUBLES AND ALARM MEMORY B. Displaying Trouble Information All trouble messages need to be reviewed and corrected as described below: EXAMPLE: The kitchen device - zone No. 9 - has reported a low battery – the living room device zone No. 15 has been inactive, and an attempt to communicate a message to your telephone has failed. However, these troubles do not prevent the system from being “ready to arm”.
REVIEWING TROUBLES AND ALARM MEMORY Correcting Trouble Situations The trouble indications (illuminated TROUBLE indicator and flashing TRBL message) are cleared once you eliminate the cause of trouble. The table below describes the system faults and respective corrective actions. If you do not know how to correct a trouble situation, report it to your installer and seek his advice. Fault What it means 1-WAY The device functions but cannot "hear" the panel.
MENUS AND FUNCTIONS 6. Menus and Functions This chapter explains the user programming features of your PowerMaster system and allows you to tailor the PowerMaster system according to your specific needs. The chapter is divided into three sections, as follows: Part A – Guides you how to enter/exit the User Settings menu and how to select the desired setting options. Part B – Guides you to execute the selected settings. A.
MENUS AND FUNCTIONS C. User Settings Options Menu Click until the display reads the desired setting option and then press SET ZONE BYPASS REVIEW BYPASS Use to set the Zone Bypass Scheme i.e. to bypass (exclude) faulty or unsecured ("disturbed") zones, or to clear a bypassed zone (unbypass). For further details and programming procedure see section B.1. 3 Use to quickly review the Bypass Scheme i.e. which zones are bypassed. For further details and reviewing procedure see section B.2.
MENUS AND FUNCTIONS A.2 Returning to the Previous Step or Exiting the USER SETTINGS Menu During the setting process it is frequently necessary to return to the previous setting step or option (i.e. "to go one level up") or to exit the User Settings menu. A. To Move One Level Up To move one level up during the setting process, click up or to the previous setting step: once or more. Each click will take you one level B.
MENUS AND FUNCTIONS 1. Zones will be bypassed throughout one disarm-arm period only. Disarming the system after arming will suspend the entire bypassing scheme but you can recall and reuse it as described in section B.3. 2. Fire zones cannot be bypassed. 3. Carefully read the section titled "Additional Information" according to the indicated references 1 etc – see table at end of section B.3. REMEMBER – ZONE BYPASSING COMPROMISES SECURITY! A. To Bypass a Zone 1.
MENUS AND FUNCTIONS B.2 Reviewing the Zone Bypass Scheme ♦ Here you can quickly review the Bypass Scheme i.e. the zones that are set to be bypassed during the next arming session. 1. REVIEW BYPASS 2. BYPASS LIST or 3. Enter the [USER SETTINGS] menu and select the [REVIEW BYPASS]1 .2 option and press The display reads [BYPASS LIST] Click the or buttons repeatedly to review all bypassed zones in ascending numerical order. When done, click to exit. 9 Z04: BYPASSED Z04: P1 P2 P3 4 Kitchen B.
MENUS AND FUNCTIONS B.4 Programming User Codes PowerMaster system allows you to authorize up to 8 people (PowerMaster-10 G2) / 48 people (PowerMaster30 G2) to arm and disarm the system by providing each with a unique 4 digit personal security code, and assigning them with different security levels and functionalities.
MENUS AND FUNCTIONS A. To Program a User Code 1. USER CODES 2. User 01 Code or 3. 4. User 06 Code User 06 : 234 5. Enter the [USER SETTINGS] menu, select the [USER CODES] option and press .1 The first user code "User 01 Code" is displayed. 2 At the blinking cursor position, key in the User Code you wish to program , for example, [06] for user code 6, or alternatively click the or button until the display reads, [User 06 Code].
MENUS AND FUNCTIONS B.5 Programming the Duress Code* A duress (ambush) alarm message can be sent to the Monitoring Station if you are forced to disarm the system under violence or menace. To initiate a duress message, you must disarm the system using a duress code (2580 by default). A. To Program the Duress Code 1. DURESS CODE Enter the [USER SETTINGS] menu, select the [DURESS CODE] option and .1 press 2.
MENUS AND FUNCTIONS ☺ Go to step 5 5. T01:Tag (Prox) or T05:Tag (Prox) ☺ Return to step 2 the display reads [DEVICE ENROLLED] for a short duration and then changes to read the tag's details. 4 The display shows the allocated tag serial No (user No.), which is always the first free number, for example: [T01:Tag (Prox)]. To assign the tag to another user, for example, "User No. 5", key in [05] or or button until the display reads alternatively click the [T05:Tag (Prox)] and then press to confirm.
MENUS AND FUNCTIONS Additional Information (section B.6) 1 2 For detailed instructions on how to select User Settings – refer to sections A.1 and A.2. The display shows the first enrolled Tag (Tag No.1) of the 8 tags (PowerMaster-10 G2) / 32 tags (PowerMaster-30 G2). 3 To abort enrollment press the 4 If the tag was previously enrolled in the system, the PowerMaster display reads [ALREADY ENROLLED] and then switches to the name of the tag alternating with its ID number.
MENUS AND FUNCTIONS 4b. ID No. 300-5786 B: ENROLLMENT BY DEVICE ID: Enter the 7-digit number that appears on the keyfob sticker and then press to confirm. To complete the enrollment procedure, see Note 9 in the Additional Information table below. ID ACCEPTED If a valid ID was entered, a "Happy Tune" ☺ sounds and the display reads [ID ACCEPTED] for a short duration and then changes to read the keyfob's details. Continue to step 5. The display shows the allocated keyfob serial No (user No.
MENUS AND FUNCTIONS to delete 6. The display now reads [ TO DELETE]. 8 To delete the keyfob press the button. 13 ☺ Go to step 3 DELETE KEYFOB A "Happy Tune" ☺ sounds and the display reads [DELETE KEYFOB] and returns to step 3. 14 Additional Information (sectionB.7) 1 For detailed instructions on how to select User Settings – refer to sections A.1 and A.2. 2 The LED will extinguish after several seconds.
MENUS AND FUNCTIONS B.8 Setting the Time & Time Format ♦ Here you can program or adjust the built-in-clock to show the correct time in the desired time format. ♦ You can select between a 24 hour and a 12 hour (AM/PM) time format. Carefully read the section titled "Additional Information" according to the indicated references1 etc – see table at end of this section. A. To Set the Time Format 1. TIME & FORMAT 2.
MENUS AND FUNCTIONS B.9 Setting the Date & Date Format ♦ Here you can program or adjust the built-in-calendar to show the correct date in the desired date format. ♦ You can select between a "mm/dd/yyyy" and a "dd/mm/yyyy" date format. Carefully read the section titled "Additional Information" according to the indicated references1 etc – see table at end of this section. A. To Set the Date Format 1. DATE & FORMAT DATE MM/DD/YYYY 2.
MENUS AND FUNCTIONS B.10 Enabling / Disabling Auto-Arming The PowerMaster system can be programmed to automatically arm itself on a daily basis at a predetermined time. This feature is useful especially in commercial applications, such as in stores, to ensure that the system is always armed and without having to assign security codes to employees. ♦ Here you can enable (activate) and disable (stop) the Auto-Arming. To set the Auto-Arming time – see section B.11.
MENUS AND FUNCTIONS B.12 Programming Private Phone, Email, MMS and SMS Reporting The PowerMaster system can be programmed to send various event notification messages such as alarm, arming or trouble events, to 4 private telephone subscribers by audible signal and, if a GSM option is installed, also to 4 SMS telephone numbers.
MENUS AND FUNCTIONS B. To Program a Private Phone 6. REPORTED EVENTS or 7. 2nd private tel# 8. 032759333 9. or button until the display reads the Telephone No. Click the you wish to program or edit, for example, "2nd private tel#", and press . To program or edit the phone number, at the blinking cursor position enter the phone number, for example, “8032759333”, using the numerical keypad. 6, 7 When done, press 8032759333 ☺ Return to step 7 to confirm.
MENUS AND FUNCTIONS E. To Program the Acknowledge Method 18. Voice<- ->private or Click the and press or button until the display reads [Tel. acknowledge] to confirm. 12 Tel. acknowledge 19. by single ack 20. or by all ack The display shows the currently selected option. Click the or button until the display reads the desired acknowledge method, for example, "by all ack". 11 21. single ack ☺ Return to step 19 A "Happy Tune" ☺ sounds.
MENUS AND FUNCTIONS EMAIL BY SERVER A. To Program Events to be Reported by Email via the server 1. PRIVATE REPORT 2. VOICE REPORT 3. EMAIL BY SERVER 4. 1st E-MAIL or Enter the [USER SETTINGS] menu, select the [PRIVATE REPORT] option .1 and press When the display reads [VOICE REPORTS] press the display reads [EMAIL BY SERVER]. repeatedly until . The display reads [1st E-MAIL].
MENUS AND FUNCTIONS MMS/SMS BY SERVER A. To Program Events to be Reported by SMS via the server 1. PRIVATE REPORT 2. VOICE REPORT 3. SMS/MMS BY SRVR 4. 1st SMS/MMS or Enter the [USER SETTINGS] menu, select the [PRIVATE REPORT] option .1 and press When the display reads [VOICE REPORTS] press the display reads [SMS/MMS BY SRVR]. To enter this option, press repeatedly until . The display reads [1st SMS/MMS].
MENUS AND FUNCTIONS disable report 15. or alarm 16. The display shows the currently selected option. Click the or button until the display reads the event group you wish to be reported via MMS, for example, [alarm]. 14 When you are satisfied with the setting, press alarm ☺ Return to step 14 to confirm. A "Happy Tune" ☺ sounds. The display confirms the set events to be reported, and returns to step 14. 5, 15 C. To Program MMS and SMS Telephone Numbers 17. 18. Continue from step 4 in section A.
MENUS AND FUNCTIONS 4 The display shows the currently selected option (indicated by a symbol), for example, "disable report".
MENUS AND FUNCTIONS 14 15 The display shows the currently selected option (indicated by a symbol), for example, "disable report".
MENUS AND FUNCTIONS A. To Set the Scheduler 1. SCHEDULER 2. PGM Enter the [USER SETTINGS] menu, select the [SCHEDULER] option and press .1 When the display reads [PGM], press . B. To Set the Day 2 The 1st day of the scheduler is displayed. Sunday 3. Click the or button until the display reads the day you wish to schedule or "Daily", for example, "Tuesday". 2 or Tuesday 4. When the "day" to schedule appears on the display, press C. To Select the Activation No. 5. operation No 1 .
MENUS AND FUNCTIONS Additional Information (section B.14) 1 2 3 4 5 6 7 For detailed instructions on how to select the Setting Options – refer to sections A.1 and A.2. To activate the selected device on every day of the week at the same time(s), use the "Daily" option. Otherwise, use the or buttons to select the specific day (Sunday, Monday, Tuesday…etc) you wish to activate the PGM output. You can later repeat the process for other days of the week, if desired.
MENUS AND FUNCTIONS B.15 Volume Control The system allows you to adjust the volume level of the various system beeps, chime signal and voice prompts, and to enable or disable status dependent, pre-recorded verbal messages (Voice option) that are heard over the built-in loudspeaker.
MENUS AND FUNCTIONS C. To Adjust the Volume Level of the Exit Entry Beeps 9. or 10. button until the display reads [Exit Entry Click the or beeps], and press . Exit/Entry beeps MID or 11. MAX 12. The display shows the currently selected option. 2 Click the or button until the display reads the desired volume level for the Exit/Entry beeps, for example, [MAX]. 3 When you are satisfied with the setting, press MAX to confirm. 6 A "Happy Tune" ☺ sounds.
MENUS AND FUNCTIONS F. To Adjust the Volume Level of the Voice Announcements 5 21. or Click the or and press 22. button until the display reads [Voice volume], . Voice volume MID The display shows the currently selected option. 2 23. or MAX 24. Click the or button until the display reads the desired volume level for the voice announcements, for example, [MAX]. 3 When you are satisfied with the setting, press MAX to confirm. 6 A "Happy Tune" ☺ sounds.
MENUS AND FUNCTIONS B.16 Serial Number The SERIAL NUMBER menu enables reading the system serial number and similar data for support purposes only. ♦ Here you can read the system serial number and other relevant data. Carefully read the section titled "Additional Information" according to the indicated references1 etc – see table at end of this section. 1. SERIAL NUMBER 2. 090703000 3. JS702271 I18.040 Enter the [USER SETTINGS] menu, select the [SERIAL NUMBER] option and press .
EVENT REPORTING & CONTROL BY TELEPHONE AND SMS 7. Event Reporting and Control by Telephone and SMS Event notifications by Telephone The PowerMaster can be programmed for selective notification of event messages to private telephone subscribers – See Chapter – 6, B.12 Programming Private Phone, Email, MMS and SMS Reporting.
EVENT REPORTING & CONTROL BY TELEPHONE AND SMS Event notifications by SMS Note: This feature is not to be not to be enabled in UL Listed product. The PowerMaster system when equipped with a GSM unit can be programmed to send SMS event notification messages to 4 pre-selected telephone numbers - see Chapter – 6, B.11. The messages can be tagged with a "House ID" name, for example, "JOHN'S HOUSE", see Remote Control by SMS section, command no. 10.
EVENT REPORTING & CONTROL BY TELEPHONE AND SMS Command 8 9 10 11 12 13 14 15 16 17 Single Partition Keying Sequence Review status of specific partition (Voice version only) 1, 2 Activating PGM output 1 Deactivating PGM output 1 Two-way voice communication 1 (see sub-par.
EVENT REPORTING & CONTROL BY TELEPHONE AND SMS Remote Control by SMS Note: This feature is not to be not to be enabled in UL Listed product. PowerMaster system with GSM unit can respond to SMS commands from any cellular telephone (a detailed SMS message sending process is described in the cellular telephone user’s guide). The various SMS commands are detailed in the following table. In this table, “” means a 4-digit user code and simply means blank space (see Note).
SPECIAL APPLICATIONS AND FUNCTIONS 8. Special Applications and Functions Looking after People Left at Home In addition to acting as an alarm system, the PowerMaster can also be used to monitor the movement of people at home when the system is in the disarmed state (or even when armed “HOME” with perimeter protection only), and report lack of motion in interior zones if there is no detection of motion within predetermined time limits.
TESTING THE SYSTEM 9. Testing the System Periodic Test The components of your security system are designed to be maintenance-free as much as possible. Nevertheless, it is mandatory to test the system at least once a week and after an alarm event to verify that all system sirens, detectors, keyfobs, keypads and other peripherals function properly. Proceed as described in this section and if there is any problem, notify your installer at once.
TESTING THE SYSTEM Z01:Temp. Sensor between the temperature, the sensor number and the sensor location. 8 button to review the temperature of each zone Repeatedly click the (by Temperature Sensor). Guest room 9. DEVICE TESTS END or When the temperature of all zones has been reviewed, the display reads or the button to confirm the [DEVICE TESTS END]. Press the test and then move to the next step to test the other devices. D. To Test all other Devices TEST ALL DEVICES 10. 11.
TESTING THE SYSTEM Periodic Test per Partition In addition to the regular Periodic Test, you can also test zones for enrolled sensors (excluding temperature sensors and sirens) that are assigned to a selected partition. A. To Conduct the Periodic Test per Partition 1 1. P1:R P2:N P3:- Make sure the selected partition is disarmed and the other partitions are not ) button. in exit or entry delay and then press the partition ( MEMORY TROUBLE 2.
MAINTENANCE 10. Maintenance Replacing the Backup Battery There is generally no need to replace the battery since the battery is rechargeable. If a CPU LOW BATTERY trouble message is received when the control panel is connected to AC power and this trouble state continues for more than a few hours, the battery may need to be replaced. An original Visonic battery must be used of which there are a number of types. For assistance in battery replacement, contact Technical Support.
MAINTENANCE READY 00:00 1. ENTER CODE:_ 2. CODE When the PowerMaster display reads [ENTER CODE: _], enter the current master user code. LIST OF EVENTS The "Happy Tune" will sound and the PowerMaster display will read [LIST OF EVENTS]. (see Important Note!) 3. Z13 alarm 09/02/10 3:37 P Click the button. The latest event will be shown. The event is displayed in two parts, for example, "Z13 alarm" then "09/02/10 3:37 P".
APPENDICES APPENDIX A. FUNCTIONS OF CONTROLLING DEVICES A1. KP-160 PG2 Arming and Disarming the System Optional Optional Step Operation 1 Select a PARTITION (if Partition is enabled) 2 Arm AWAY 3 4 User Actions Keyboard & Panel Response The selected key blinks.
APPENDICES A2. KP-140/141 PG2 Arming and Disarming the System Step 1 Basic Arming User Actions Select a PARTITION (Partition enabled) Keypad & Panel Response The selected button lights. or or The selected button starts blinking and prompts you to enter your "User Code" or present your Tag. See step 3. Arm AWAY Arm HOME 2 Disarm (OFF) The keypad's LED blinks red once to indicate transmission of the arming command to the control (≈ 2 sec.) panel.
APPENDICES A3. KF-234 PG2 Keyfob Functionality Step Functions User Actions Arm AWAY 1 When executing a command, the keyfob's LED blinks red once to indicate transmission of the command to the control panel. If the operation is successfully completed, the green LED lights momentarily and a "happy tune" is heard.
APPENDICES APPENDIX B. PARTITIONING The control panel includes an optional partition feature. Partitioning is available only if your installer has enabled the feature. Once partitioning is enabled Partitioning menus are added to the system which can be viewed on the control panel's LCD display. Partitioning allows you to divide the system into three independently controllable areas with different users assigned to each partition whereby each user can arm the partition to which they are assigned.
APPENDICES B4. Siren A partition is alarmed when receiving an event from an alarmed device assigned to that partition. Alarmed devices do not affect partitions to which they are not assigned. A siren is common to all partitions; therefore, an alarm from one or more partitions will activate the siren. Siren Activity • The siren will be activated when receiving an event from an alarmed device. • Overlapping siren activations from different partitions will not cause the duration of the siren to be extended.
APPENDICES Table A1 – Common Area Definitions Common area zone types Definition Perimeter • Acts as defined only after the last assigned partition is armed AWAY or HOME. • In case that one of the partitions is disarmed, an alarm initiated from this zone is ignored for all assigned partitions. Delay zones • Delay zones will not trigger an entry delay unless all assigned partitions are armed. It is, therefore, not recommended to define delay zones as common areas.
APPENDICES APPENDIX C. GLOSSARY This list of terms is arranged in alphabetical order. Abort Period: When an alarm is initiated, the internal built-in sounder is activated first for a limited period of time which is the abort period set by the installer. If you cause an alarm accidentally, you can disarm the system within the abort period before the real sirens start and before the alarm is reported to the remote responders.
APPENDICES HOME: This type of arming is used when people are present within the protected site. A classic example is night-time at home, when the family is about to retire to bed. With HOME arming, perimeter zones are protected but interior zones are not. Consequently, motion within interior zones will be ignored by the control panel, but disturbance of a perimeter zone will cause an alarm.
APPENDICES APPENDIX D. HOME FIRE ESCAPE PLANNING Fire can spread rapidly through your home, leaving you a short time to escape safely. Your ability to get out depends on advance warning from smoke detectors and advance planning - a home fire escape plan that everyone in your family is familiar with and has practiced. • Pull together everyone in your household and make an evacuation plan. • Draw a floor plan of your home, showing two ways out of each room, including windows.
APPENDICES APPENDIX E. SPECIFICATIONS E1. Functional Zones Number Hard-wired Zone Requirements Maximum Loop Current Maximum Loop Voltage Loop Shorted Loop Normal Loop Tampered Loop Alarm Loop Open Installer and User Codes Control Facilities Display Arming Modes Alarm Types Siren Signals Siren (bell) Timeout Internal Sounder Output Supervision Special Functions Data Retrieval 68 PowerMaster-10 G2 30 wireless zones (including 1 hard-wired input). 2.2 kΩ E.O.L. resistance (max.
APPENDICES Real Time Clock (RTC) Battery Test PowerMaster-10 G2 The control panel keeps and displays time and date. This feature is also used for the log file by providing the date and time of each event Once every 10 seconds PowerMaster-30 G2 The control panel keeps and displays time and date.
APPENDICES PowerMaster-10 G2 PowerMaster-30 G2 (2) 7.2V 1300 mAh, rechargeable NiMH battery pack, p/n 130AAM6BMX, manufactured by GP or p/n LTTAA1300LSDX6B, manufactured by LTT. (3) 9.6V 1800 mAh, rechargeable NiMH battery pack, p/n GP180AAH8BMX, manufactured by GP or p/n LTTAA1800LSDX8B, manufactured by LTT. (4) 9.6V 2200 mAh, rechargeable NiMH battery pack p/n 220AAH8BMX, manufactured by GP or p/n LTTAA2200LSDX8B, manufactured by LTT.
APPENDICES Message to Private Phones Ring Detection Tone Tone or voice The unit does not support ring detection without DC voltage present on the telephone lines. The unit does not support ring detection without DC voltage present on the telephone lines E5. Physical Properties Operating Temp. Range Storage Temp.
APPENDIX F. COMPLIANCE WITH STANDARDS Compliance Statement Hereby, Visonic Group declares that the PowerG series of central units and accessories are designed to comply with: U.S. Standards: (FCC) CFR 47 part 15 and part 68, UL 1023 and UL 985 Canada Standards: RSS 210 European CE Standards The PowerMaster complies with the RTTE requirements - Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999.
© 2013 Visonic Ltd. All rights reserved. PowerMaster-10 / PowerMaster-30 English User Guide D-304829 USER GUIDE PowerMaster-30 G2 Fully supervised wireless alarm control system www.visonic.
