Installation Instructions & User’s Manual VISIONXLIGHTING.
VISION X About The XPL LED Light Bar: *Accessories in Box May Vary FEATURES 1. Ultra slim housing with back-lit housing. 2. IRIS reflector technology for ultimate distance. 3. Dual mounting options; end cap wings and mounting feet. XPL LED LIGHT BAR SPECIFICATIONS 1. Warranty : Extended 2. Amp Draw : 1.25A - 16.25A @ 12V DC 3. Input Voltage : 9-32V DC 4. Beam Patterns : Spot 5. LED Lifespan : 50,000 Hours PREPARATION 1. We recommend completely reading instructions before installing. 2.
XPL LED LIGHT BAR 1 LIGHT 4 2 XPL Qty: 1 Wing Mounts (Optional) PART (W1) Qty: 2 WIRING 5 Qty: 1 Wing Bolt PART (B1) Bolt 7 Hex Head 8 [M8] PART (M1) Qty: 2 Single Light Harness (Optional) Qty: 2 Washer [M8] PART (M2) Qty: 2 3 Mounting Feet PART (F1) 6 Qty: Varies on size Rubber Grommet PART (G1) Qty: 2 9 Nylock Nut [M8] PART (M3) Qty: 2
VISION X WIRING INSTALLATION INSTRUCTION 1. Find a suitable place to mount Relay Part (R1) leaving enough room for Power & Ground wires Part (W1 & W2) to reach the battery & the Deutsch connector Part (C1) to reach the Light. Mount Relay. 2. Run Power wire (W1) & Ground wire (W2) to the battery. Connect the Power wire (W1) to the Positive (+) battery terminal and connect the Ground wire (W2) to the Negative (-) battery terminal. 3. Run the Deutsch connector wire (C1) to the light and plug in. 4.
XPL LED LIGHT BAR WIRING DIAGRAM: (R1) (-) (W2) (P1) (S1) (W1) (+) (C1) *To Light HALO WIRE: (H1) Halo wire COMPONENTS KEY Part (R1) Relay Part (W1) Power Wire for Relay Coil a. 9-32V DC Positive (+) Input Wire Part (W2) Ground Wire for Relay Coil a. 9-32V DC Negative (-) Input Wire Parts (C1) Deutsch Connector for Light a.
VISION X WARNING: Bolts, Nuts, and Washers are Stainless Steel. DO NOT USE Pneumatic or Electric Tools to Tighten and Loosen. The Hardware Will Permanently Lock Together. MOUNTING INSTALLATION INSTRUCTION FOR WINGS (END CAPS) 1. Insert two (2) rubber grommets Part (G1) on each side of the LED bar over the appropriate threaded bolt holes. See [Figure 1] 2. Place the mounting wings Part (W1) over the rubber grommets (G1) and insert the wing bolts Part (B1). See [Figure 2] 3.
XPL LED LIGHT BAR INSTALLATION IMAGES WING INSTALLATION IMAGE Fig. 1 Fig. 5 (Wing Mounting) (M1) Fig. 2 (W1) Mounting Wing (Wing Mounting) (M2) Fig. 3 (Feet Mounting) (M3) LIGHT ANGLE ADJUSTMENT 1. With Mounting Feet : Use 13mm wrench / sockets to loosen bolts on mounting feet. Slide the light bar up or down to angle the beam. Once desired angle is achieved, tighten the bolts. See [Figure 3] 2.
You May Also Be Interested In: Part # - 4000308 Item # - XIL-LICENSEP License Plate Bracket for Light Bars up to 20” CLAMP TUBE MOUNT (0.75”-3.0” Diameters Available) SECURITY NUT Available in multiple sizes VISIONXLIGHTING.