Visioneer Strobe XP 450 USB Scanner Installation Guide FOR WINDOWS
COPYRIGHT INFORMATION Copyright © 2003 Visioneer, Inc. Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws. The Visioneer brand name and logo are registered trademarks of Visioneer, Inc. The PaperPort brand name and logo are registered trademarks of ScanSoft, Inc. Microsoft is a U.S. registered trademark of Microsoft Corporation. Windows is a trademark of Microsoft Corporation.
i TA B L E O F C O N T E N T S Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 What’s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 The Visioneer Strobe XP 450 Scanner . . . . . . . . . . . . . . . . . . . . . . . . 2 What You Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ii Reversing the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Adjusting Color and Gray Images . . . . . . . . . . . . . . . . . . . . . . . 36 Adjusting Color Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Adjusting the Scanner’s Power Saving Time . . . . . . . . . . . . . . . 44 Scanning from Windows Me or XP . . . . . . . . . . . . . . . . . . . . . . . . . 45 Chapter 4: Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WELCOME 1 WELCOME Your Visioneer Strobe XP 450 USB scanner can quickly scan color and black and white documents and place their images on your computer. Warning: Do not plug in the USB cable until after you have installed the software. Carefully follow the steps and sequence described in the installation procedure beginning on page 5. WHAT’S IN THE BOX Before proceeding, check the contents of the box. If items are missing or damaged, contact the dealer where you purchased the scanner.
2 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE THE VISIONEER STROBE XP 450 SCANNER Paper guide Scanner button Status light Output tray Output tray extension ADF cover release Power switch Power jack USB port Paper guide—Holds documents in place. Adjusts to fit the document size. Scanner button—Starts scanning using the scan settings button. Status light—Shows the scanner’s status. A flashing green light indicates the scanner is preparing to scan.
WHAT YOU NEED 3 WHAT YOU NEED An IBM-compatible PC with: ■ A CD-ROM drive ■ An available Universal Serial Bus (USB) port ■ Microsoft Windows operating system: 98, 2000, Me, or XP ■ Available internal memory (RAM) as follows: ■ ■ 64 megabytes (MB) ■ Windows XP—128 MB 200 MB of free hard disk space Note: The new USB 2.0 ports operate at higher speeds than USB 1.1 ports. If your computer is not equipped with USB 2.0 ports, you can add them with the Visioneer Hi-Speed USB 2.0 PCI Card.
4 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE DOCUMENTATION Your scanner is delivered with the following documentation: ■ Quick Install Card—abbreviated installation instructions. ■ Visioneer Strobe XP 450 Scanner Installation Guide—on the Installation CD; contains detailed installation, scanning, configuration, and maintenance information. ■ ScanSoft PaperPort User’s Guide—on the Installation CD; contains detailed feature and configuration information.
STEP 1: ASSEMBLE THE SCANNER 5 Installation Warning: Do not plug in the USB cable until after you have installed the software. Complete the installation steps in the order described in the installation procedure below. Installation is a quick, four-step process: 1. Assemble the scanner 2. Connect and power on the scanner 3. Install the software 4. Connect the USB cable to your computer STEP 1: ASSEMBLE THE SCANNER To assemble the scanner: 1.
6 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE 3. Insert the pins on each side of the output tray into the holes on the scanner. 4. Proceed to “Step 2: Connect and Power On the Scanner”. STEP 2: CONNECT AND POWER ON THE SCANNER Before installing the software, connect the power supply and power cord, and then turn the power on. To connect your Visioneer Strobe XP 450 scanner: 1. Plug the power supply into the power port on the scanner.
STEP 3: INSTALL THE SOFTWARE 7 2. Plug the power cord into the power supply and into a wall outlet. 3. Turn on the power switch, located on the back of the scanner to the left of the power port. The status light comes on and flashes indicating that the scanner is receiving power. STEP 3: INSTALL THE SOFTWARE Note: You must install the software before connecting the scanner to your computer. Otherwise, the correct driver software for your scanner will not be installed and it may not work properly.
8 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE Note: If the CD does not start, check the following: ■ Make sure the CD drive’s door is completely shut. ■ Double-click the My Computer icon on your Windows desktop. Double-click the icon for your CD-ROM drive. From the list of files on the CD, double-click the file named START32.EXE. 3. On the installation menu, select Install ScanSoft PaperPort and Scanner Driver. If a message window opens instructing you to restart your computer, click Restart. 4.
STEP 4: CONNECT THE USB CABLE 9 13. When you see the Connect Scanner window, do NOT click Finish. Leave the window open and proceed to the next section, “Step 4: Connect the USB Cable”. STEP 4: CONNECT THE USB CABLE The Visioneer Strobe XP 450 scanner connects to any available USB port. Check your computer’s manual for USB port locations. Note: You can connect the scanner to your computer while the computer is running. You do not have to shut down your computer. 1.
10 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE Note: You can also connect the scanner to a USB port on the computer’s keyboard if it has one, or to a USB hub. If you use a USB hub, it must have its own power supply already plugged into an electrical outlet. Note: If you have not installed the software, unplug the USB cable from the computer and install the software now. When the software installation is complete, a message tells you to connect the scanner.
LOAD AND SCAN DOCUMENTS 11 Scanning with the Scanner Button When you press the scanner button, your document is scanned using predefined scan settings and then the image is sent to a software application on your computer. To change scan settings, see “Configuring the Scanner Button” on page 13. LOAD AND SCAN DOCUMENTS 1. If you are scanning legal-sized documents, unfold the output tray extension. 2. Adjust the paper guide for the size of paper.
12 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE 3. Load the documents face down, with their tops into the automatic document feeder. 4. Press the button on the scanner. A scan progress window opens and then a thumbnail of the scanned image appears in the destination software. In the following example, the destination software is the PaperPort desktop.
CONFIGURING THE SCANNER BUTTON 13 CONFIGURING THE SCANNER BUTTON When you first connect your scanner to a computer, the scanner’s OneTouch software is configured to scan in black and white and send the scanned image to the PaperPort desktop. You can change the settings by selecting new options from the Configuration dialog box. To open the Configuration dialog box: 1. On the Windows taskbar, click Start, point to Programs, point to ScanSoft PaperPort 9.0, and then click OneTouch Configure. 2.
14 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE The options on the Configuration dialog box are: Select Destination—the list of applications that can open to display the scanned image. To configure the list of available applications, click the Preferences tab at the top of the dialog box and select the desired option. See “Setting Preferences” on page 20 for more information. Select Configuration—the list of available configurations.
CONFIGURING THE SCANNER BUTTON 15 SELECTING NEW SETTINGS FOR THE SCANNER BUTTON You can select a new destination application, scanning configuration, and image format to use when you press the scanner button. To select new settings for the Scanner Button: 1. From the Select Destination list, select the application where you want scanned images sent. See “Setting Preferences” on page 20 to display a full list of the destination applications that you can use with the scanner.
16 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE CREATING A NEW BUTTON CONFIGURATION You cannot change settings of the preset (default) configurations. To use settings other than those offered by the preset configurations, you must create a new configuration. You can do this either by copying a preset configuration and making the desired changes or by creating a new configuration from scratch. To create a new configuration: 1.
CONFIGURING THE SCANNER BUTTON 17 4. Select scan settings for the new configuration. Mode—Select a scanning mode as follows: ■ Black/White to scan in black and white. For example, letters and memos are usually scanned in black and white. ■ Grayscale to scan items such as documents containing drawings or black and white photographs. The scanning produces an image in varying shades of gray. ■ Color to scan color photographs and other color items.
18 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE select the Custom option from the drop-down list, boxes appear in place of the picture. Enter the horizontal and vertical page dimensions in the boxes. AutoCrop—This option lets the scanner automatically determine the size of the item being scanned. For example, if you scan an unusual page size, the scanner will automatically determine the size of the page.
CONFIGURING THE SCANNER BUTTON 19 7. To set the new configuration for use by the scanner button, select the configuration and then click OK. EDITING BUTTON CONFIGURATIONS You cannot edit the preset button configurations; you can only edit those configurations that you created yourself. To edit a configuration: 1. Open the Configuration dialog box. 2. Select the configuration you want to edit. The selection must be a configuration you created. 3. Click the Edit button.
20 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE SETTING PREFERENCES You can set general preferences for button and scanner functions. To set preferences: 1. Open the Configuration dialog box and click the Preferences tab. Preferences tab 2. Select button preferences as described below. Show All Destinations—This option selects all the destination application categories.
CONFIGURING THE SCANNER BUTTON 21 3. Click the General tab to set a temporary folder. Folder for Temporary Images—Click the Folder button and then select a folder for the scanner’s temporary images. During scanning, a temporary file contains scan information about the image. Because temporary image files can sometimes be large, select a folder that has sufficient disk space available. 4. Click OK to save the AutoScan preferences.
22 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE Scanning from PaperPort Instead of using the scanner button, you can scan from the PaperPort software application. Use this method if you want to preview an image and adjust scanning settings prior to scanning. YOUR SCANNER AND THE TWAIN STANDARD Your scanner uses the TWAIN standard for scanning. TWAIN is a widely recognized methodology that computers use to receive images from scanners, digital cameras, and other digital devices.
LOAD DOCUMENTS INTO THE DOCUMENT FEEDER 23 LOAD DOCUMENTS INTO THE DOCUMENT FEEDER 1. If you are scanning legal-sized documents, unfold the output tray extension. 2. Adjust the paper guide for the size of paper. Note: Remove any staples or paper clips from the documents before loading them into the automatic document feeder. Staples and paper clips can jam the feed mechanism. 3. Load the documents face down, with their tops into the automatic document feeder.
24 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE SCANNING FROM WINDOWS 98, ME, 2000, OR XP The instructions in this section are for scanning with the TWAIN software on computers running Windows 98, Me, 2000, or XP. If your computer is running Windows Me or XP and you want to use the WIA software, see “Scanning from Windows Me or XP” on page 45. To scan an item from PaperPort: 1. On the Windows taskbar, click Start, point to Programs, point to ScanSoft PaperPort 9.0, and then click PaperPort.
SCANNING FROM WINDOWS 98, ME, 2000, OR XP 25 Scan pane Opens the Scan Manager 3. From the Scanner drop-down list, select Strobe XP 450. 4. In the “Scan what?” section, choose to scan a Document or Photograph. 5. Click Settings to view and change the format for the scanned item’s file name and the file type. The default file type for documents is .pdf and the default for photographs is .jpg. 6.
26 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE 8. If you want to see what the scanned image will look like before scanning its final image, click the Preview button. The scanner scans a preview of the item and displays it in the Scan Manager. You can now use the options on the Scan Manager to fine-tune the image. For details on adjusting images, see “Adjusting the Image with the Scan Manager” on page 28.
SCANNING FROM WINDOWS 98, ME, 2000, OR XP A thumbnail image of the scanned item appears on the PaperPort desktop 27 Thumbnail images of a stack of documents scanned with the ADF. ON THE PAPERPORT DESKTOP ■ By default, the name of the scanned image is the day, date, and number of scanned items that day. For example, the second item scanned on a day is followed by a (2), the third by a (3) and so on. To change a name, click it to select its text and type a new name.
28 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE ■ Click Scan More Pages to scan additional pages and add them to the stack of items placed on the PaperPort desktop. ■ Click Scan Other Side to reload and scan the other side of previously scanned pages. This option is only available once. ■ Click Done if you are finished scanning. The scanned items are placed on the PaperPort desktop.
SCANNING FROM WINDOWS 98, ME, 2000, OR XP 29 Image Type Resolution Brightness Contrast IMAGE TYPE From the Image Type drop-down list, select the appropriate image type for the item(s) you’re scanning: Halftone Example ■ Black and White—scans in black and white. The scanning pixels are all the same size and are either black or white. Use this setting for letters, memos, pen and ink drawings, and other black and white material. This setting produces the smallest file size for scanned items.
30 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE ■ 8-Bit Gray—scans the image using up to 256 true shades of gray. Use this setting to scan black and white photographs and other higher quality black and white images. You can also scan a color photo with this setting to turn its colors into gray shades. The file size is about one third the size of a color scan. ■ 24-Bit Color—scans the image in full color. Use this setting to scan color photographs and other color images.
SCANNING FROM WINDOWS 98, ME, 2000, OR XP 31 Brightness refers to the lightness or darkness of the image. Contrast is the range between the darkest and lightest portions of the image. The greater the contrast, the more the difference between the lighter and darker shades in the image. ■ Dark/Light slider—adjusts the brightness of the scan. Drag the slider to the right or left to increase or decrease the brightness. ■ Low/High slider—adjusts the contrast.
32 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE ■ Click the Preview Auto-Area button to let the Scan Manager automatically determine the size of the item being previewed. For example, if you preview the scan of a small photo, the Scan Manager automatically determines that the scan area is only the edges of the photo. You can manually adjust the scan area. For example, if you want the scan to include a border around the image, drag the edges of the scan area box.
SCANNING FROM WINDOWS 98, ME, 2000, OR XP 33 SETTING THE SCAN AREA You can manually adjust the output area to scan specific sections of an image. For example, if you’re scanning a photograph and want to focus on one section, manually setting the output size removes the rest of the photograph from the final scanned image. Move pointer Manually set area Resize pointer Output Dimensions To manually set an output area: 1.
34 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE Here’s a sample of a manually selected output area: This is the area manually selected for scanning. This is the image that appears on the PaperPort desktop when scanning is finished. Lock Scaling MANUALLY SETTING THE WIDTH AND LENGTH The output dimensions at the bottom of the Scan Manager show the Width and Length of the scan area. You can set the area by typing numbers into those boxes. To manually set the width and length: 1.
SCANNING FROM WINDOWS 98, ME, 2000, OR XP REVERSING THE IMAGE The Scan Manager has an Invert button and a Mirror button for reversing the scanned image. Invert Mirror Invert reverses the black and whites or the colors of an image. Mirroring flips the image 180 degrees. ■ Click the Invert or Mirror button to see the image you want.
36 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE ADJUSTING COLOR AND GRAY IMAGES The Scan Manager has three buttons—Descreen, Sharpen, and Auto Level—for adjusting color and gray images. These buttons are available when the 24-Bit Color or 8-bit Gray Image Types are selected. Descreen Sharpen Auto Level DESCREEN IMAGE Select this option when scanning a picture from a newspaper or magazine article, sales catalog, or other source that contains images with patterns or dots.
SCANNING FROM WINDOWS 98, ME, 2000, OR XP 37 To descreen an image: 1. Click the Descreen button. 2. Choose the appropriate option from the list. Watch the preview image as you select various options to see which one is best for your final scanned image. SHARPEN IMAGE Sharpness determines the amount of blur in an image. Your scanner can sharpen an original blurred image by adjusting the blurry edges in sections of the image. To sharpen an image: 1. Click the Sharpen button. 2.
38 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE AUTO LEVEL Your scanner can analyze a color image to automatically determine the best settings to match the colors of the original image. Click this button to let the scanner automatically adjust the color settings. Original Image AutoLevelAdjusted ADJUSTING COLOR SETTINGS The buttons for manually adjusting a preview image’s color settings offer several advanced color options.
SCANNING FROM WINDOWS 98, ME, 2000, OR XP 39 HIGHLIGHT/SHADOW LEVELS Images have light and dark areas. The highlight is the lightest spot on an image; shadow is the darkest spot. The range of colors between the highlight and shadow determines the range of colors of the image. Use the Highlight/Shadow Levels to extend the original range of colors between the highlight and shadow to reveal more details in the midrange colors. To adjust the highlight and shadow levels: 1. Click the Highlight/Shadow button.
40 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE 4. Click Preview to see the effect of the changes on the preview image. 5. Click Reset to reset the levels to their original values. 6. Click OK when the levels are what you want. CURVES Like the Highlight/Shadow levels, the Curves feature also adjusts the range of midtone colors on an image. However, with the Curves feature you can set the gamma individually to adjust midtone levels without losing details from the lightest or darkest areas.
SCANNING FROM WINDOWS 98, ME, 2000, OR XP 41 3. Drag the line up or down to set a new gamma. The input and output values represent values on the horizontal and vertical axes for the new gamma setting. Click the Curve or Line button to see the display as a smooth curve or a line. You can drag the line at multiple points. 4. Click Preview to see the effect of the changes on the preview image. 5. Click Reset to reset the levels to their original values. 6. Click OK when the levels are what you want.
42 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE 4. Click Reset to reset the levels to their original values. 5. Click OK when the levels are what you want. HUE/SATURATION/LIGHTNESS Hue is the color your eyes see as reflected from the image, saturation is the strength or purity of a color and determines whether a color is pale or rich, and lightness is the intensity of the color. To adjust the hue/saturation/lightness: 1. Click the Hue/Saturation/Lightness button.
SCANNING FROM WINDOWS 98, ME, 2000, OR XP 43 COLOR DROP-OUT Color drop-out is the ability of your scanner to automatically remove one color from a scanned item. For example, if you are scanning a letter with a red watermark, you can choose to drop-out the color red (the R Channel) so the scanned letter just shows the text and not the red watermark. Color drop-out applies when you select the scanning image types of Black and White, Halftone, 8-Bit Gray or 16-Bit Grayscale.
44 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE To drop the color out of a black and white, or grayscale image: 1. From the Image Type list, choose Black and White, Halftone, 8-Bit Gray, or 16-Bit Grayscale. 2. Click the Color Drop-out icon. 3. On the Color Drop-out dialog box, choose a color to drop out. 4. Click OK. Now when you scan the black and white or gray item, the selected color is removed.
SCANNING FROM WINDOWS ME OR XP 45 SCANNING FROM WINDOWS ME OR XP If your computer is running the Windows Me or XP operating system, you have a choice of scanning using the TWAIN-compliant Visioneer Scan Manager software as just described (see “Scanning from Windows 98, Me, 2000, or XP” on page 24) or scanning using the Microsoft Windows Image Application (WIA) standard as described below.
46 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE 4. In the “Scan what?” section, choose to scan a Document or Photograph. 5. Click Settings to view and change the format for the scanned item’s file name and the file type. The default file type for documents is .pdf and for photographs is .jpg. 6. Use the Single page items check box as follows: ■ When the check box is selected, all pages in the document feeder are scanned and placed in a stack on the PaperPort desktop.
SCANNING FROM WINDOWS ME OR XP 47 Note: If you preview when scanning a stack of documents, the first page of the stack feeds through the ADF for the preview. After adjusting the scanner settings, replace that page on the stack so it is scanned with the rest of the pages. 12. Adjust settings of the previewed image as desired: ■ Change the button selection for the type of image. ■ Adjust the custom settings; refer to the next section, “Fine Tuning Your Scans”. ■ Change the size of the scanned image.
48 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE FINE TUNING YOUR SCANS You can select new settings before you scan an item to fine tune exactly how you want to scan a particular item. To select the scanner settings before you scan: 1. On the Scan using Strobe XP 450 window, click Adjust the quality of the scanned picture. The Advanced Properties dialog box opens. 2. Select the options for scanning.
SCANNING FROM WINDOWS ME OR XP 49 Brightness and Contrast—Drag the sliders to the right or left to adjust the brightness and contrast of the scanned image. The Contrast setting does not apply to the setting Black and White picture or text. Resolution (DPI)—Click the drop-down list and choose the dots per inch (dpi) of the resolution. The maximum resolution is 600 dpi; the minimum is 50 dpi. The higher the dpi setting, the sharper and clearer the scanned image.
50 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE Maintenance This chapter contains information on maintenance, troubleshooting, uninstalling, scanner specifications, and spare parts. CLEANING THE AUTOMATIC DOCUMENT FEEDER You may need to clean the ADF feed mechanism if your documents do not feed easily into the ADF, or several feed in at the same time. To clean the ADF: 1. Wet a cotton swab with some isopropyl alcohol (95%). 2.
CLEARING PAPER JAMS 51 CLEARING PAPER JAMS If your scanner stops scanning due to a paper jam in the Automatic Document Feeder, a warning dialog box opens after a few moments. To clear a paper jam: 1. Press the ADF cover release on the top-left of the scanner body to open the automatic document feeder cover. 2. Remove the jammed paper and close the cover. To reduce the number of paper jams, smooth and straighten paper before scanning and adjust the guides to the paper size.
52 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE REPLACING THE ADF PAD ASSEMBLY The ADF pad spring may begin to wear out after 150,000 scanned pages. Problems with documents feeding into the ADF is an indication that the pad spring may be wearing out. See the “Visioneer Strobe XP 450 Scanner Parts List” on page 58 for ordering information. To replace the ADF Pad assembly: 1. Press the ADF cover release on the top left of the scanner body to open the automatic document feeder cover. 2.
TROUBLESHOOTING 53 TROUBLESHOOTING In addition to the troubleshooting information contained in this section, please see the Readme file on your installation CD. The Readme file contains additional information that may help you diagnose problems with the scanner. If you try the troubleshooting procedures described in this section and in the Readme file, and the scanner still has problems, you may have a malfunctioning scanner. Refer to the technical support card that you received with your scanner.
54 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE Problem: During installation I got the error message: PaperPort Installation is not complete. What do I do? The installation procedure was not successful. You need to reinstall the PaperPort software. Problem: I got the error message: PaperPort cannot allocate enough memory to perform internal critical operations. What do I do? Close any other active applications so that additional memory is available.
UNINSTALLING YOUR SCANNER 55 UNINSTALLING YOUR SCANNER To uninstall the Visioneer Strobe XP 450 scanner, remove the scanner software first, and then remove PaperPort, or other scanner software. STEP 1: UNINSTALLING THE VISIONEER ONETOUCH SOFTWARE 1. On the Windows taskbar, click Start, point to Settings, and then click Control Panel. 2. Double-click the Add/Remove Programs icon. ■ Windows 98, 98SE, or ME: The Add/Remove Programs Properties window opens. Select the Install/Uninstall tab.
56 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE STEP 2: UNINSTALLING THE PAPERPORT SOFTWARE To uninstall PaperPort 9.0 from Windows 98SE or ME: 1. On the Windows taskbar, click Start, point to Settings, and then click Control Panel. 2. Double-click the Add/Remove Programs icon. 3. On the Add/Remove Programs Properties window, select the Install/Uninstall tab. 4. Select PaperPort 9.0 and click Remove. 5. On the Welcome window, click Next. 6.
VISIONEER STROBE XP 450 SCANNER SPECIFICATIONS VISIONEER STROBE XP 450 SCANNER SPECIFICATIONS Optical resolution 600 x 1200 dpi Bit depth 48-bit color Maximum item size 8.5” x 14” Minimum item sizes 3.5” x 2” (automatic document feeder) 2.5” x 2” (front feed) Scan method Automatic document feeder (ADF) ADF specifications Scanning Speed Up to 22 pages per minute @ 200 dpi B&W Capacity 50 sheets Paper Thickness 16 - 28 lbs. (0.002” - 0.
58 VISIONEER STROBE XP 450 SCANNER INSTALLATION GUIDE VISIONEER STROBE XP 450 SCANNER PARTS LIST Please use the following part names and numbers when ordering replacements for your scanner.
INDEX INDEX Numerics 24-bit color 29, 43 8-bit gray 29, 43 A descreen image 36 destination application OCR 15 distorted image 36 documentation 4 dots-per-inch 30 dpi 30 adjust image 28 AutoCrop cropping images 18 automatic color adjustment 38 AutoScan 11 configuring 13 G B halftone 29 help 4 highlight level 39, 40 hue 39, 42 bit depth 57 black and white 29 brightness 30 brightness slider 30 C CD other software 10 CD-ROM drive 3 color adjustment 36 automatic 38 manual setting 38 color balance 41 col
INDEX 60 N newspaper article 36 O on/off switch 7 output size 31, 33 P paper guide 5 paper size 32 PaperPort 22 desktop 24 Scan pane 24 scanning with Windows Me or XP 45 PaperPort desktop thumbnail 27 patterns on picture 36 preferences setting for AutoScan 20 tab 20 preview auto-area 31 R resolution 30 reverse image 35 RGB 39, 40 ruler units 32 S saturation 39, 42 scan file name 27 multiple pages 27 PaperPort desktop 27 preview 26 small item 31 scan area automatic setting 31 manual setting 33 Scan Ma
