TECHCONNECT AMPLIFIER OWNERS MANUAL www.visionaudiovisual.com/techconnect/tc2-amp3 1 TC2-AMP3_manual_en.
TECHCONNECT AMPLIFIER OWNERS MANUAL Thanks for choosing the Vision TC2-AMP3 digital amplifier! In order to obtain the best performance please be sure to read this owner’s manual and use your product only in accordance with the instructions. CONFORMITY The product described in this owner manual is in compliance with RoHS (EU directive 2002/95/EC), and WEEE (EU directive 2002/96/EC) standards. Certificates including SGS reports are available on request.
USE ONLY DOMESTIC AC OUTLETS Connecting the unit to an outlet supplying a higher voltage may create a fire hazard. HANDLE THE POWER CORD WITH CARE Do not disconnect the plug from the AC outlet by pulling the cord; always pull the plug itself. Pulling the cord may damage it. If you do not intend to use your unit for any considerable length of time, unplug the unit. Do not place furniture or other heavy objects on the cord, and try to avoid dropping heavy objects on it. Do not tie a knot in the power cord.
FRONT AND REAR CONTROL PANELS 12 6 11 1 5 10 4 9 2 7 3 8 1. LED Volume Indicator 2 / 8. IR receiver 3 / 9. Input 1 4. Volume Down 5. Power Switch /Input Selector 6. Volume Up 7. Power Socket 10. Right Speaker Output 11. Left Speaker Output 12. Input 2 IR REMOTE CONTROL 1 2 1. 2. 3. 4. 5. 6. 7. Input 1 Volume Up Mute Input 2 Power On Power Off Volume Down 7 3 4 5 6 4 TC2-AMP3_manual_en.
INSTALLATION INSTRUCTIONS 1. 2. 3. 4. 5. TC2 VGAF3.5MM module 3-Phono module TC2-AMP3 module Bare-wire speaker terminals UK double gang surround 3 1 4 2 5 Connect as shown: 1 1. 2. 3. 4. 5. 2 3 4 5 TC2 VGAF3.5MM module 3-Phono module DC Power TC2-AMP3 module Bare-wire speaker terminals 5 TC2-AMP3_manual_en.
NOTE 1: The speaker cable must be unshielded with a gauge of no less than 0.75mm. THE WARRANTY WILL BE VOID IF YOU USE UNSUITABLE SHIELDED CABLE. NOTE 2: THIS IS A LOW-IMPEDANCE AMPLIFIER. DO NOT ATTEMPT TO CONNECT 100V LINE SPEAKERS (Normally any speakers with “t” in the part code) Alternative Configuration 1. 2. 3. 4. Techconnect TC2-AMP3 module UK Single gang Surround Power cable 1 2 3 4 PROGRAMMING MEMORY The Techconnect Amplifier turns on automatically when mains power turned on.
To adjust settings for mode 1: 1. Check it is in mode 1. Set volume and input 2. Turn amplifier to off (standby) 3. Hold down volume+ then volume- for 5 seconds. Input indicator will flash 8 times indicating the new setting has been saved. TROUBLESHOOTING If your system is not operating properly, please refer to the following information. If the problem persists, disconnect from power and contact your AV reseller immediately. Problem Correction No Sound • Turn off and check connections.
SPECIFICATIONS • Power Output: 2 x 20 watts RMS @ 8 Ω • Total Harmonic Distortion: ≤1% (20Hz-22kHz) • Frequency Response (line in): 20Hz~22kHz(±2dB) • Signal to noise ratio (line in): ≥98dB (A-weighted) • Rating input level/impedance: Line in 500mV/50kΩ • Power Consumption: ≤40w • Power Supply 100-240vAC 50/60Hz Max 1.
