Specifications
By using latest low-impedance
digital amplifier chip technology
the new Techconnect
2
Amp
2
module outputs a massive 2 x
20w RMS (at 8 ohms) but fits into
the chassis of a double-module.
Two Inputs are wired into the rear
with removable phoenix connectors,
PLUS Input 1 is duplicated on the
front panel with a minijack socket
for convenience. This half-normalled
input disconnects the rear terminal
while in use.
Digital amplifiers use no power unless
they are working, so even on at full
volume; unless it is receiving input
it is effectively off. Digital amplifiers
run cold so a bulky heatsink is not
necessary - but don’t let size deceive
you: the Techconnect Amp
2
can drive
into a 4 ohm load powering up to four
speakers.
A clear display makes it easy to use
and a revised control interface gives
instant access to controls. Because it
can be installed anywhere in the room
it is easier to access than powered
speaker controls.
IR receivers are positioned on
the front for normal use and
on the rear for integration with
a control system such as the
Techconnect Control
2
.
Robust and easy to install; the inputs
and outputs are all via removable
phoenix connectors which allow end
users to uninstall easily if required.
Short input cables are included for
connection to the rear of adjacent
input modules on the connectivity
faceplate.
Perfect for when you don’t have
furniture to sit an amplifier on, and
because it is mounted to the wall it is
less obvious as a target for theft. It is
close at hand if volume adjustments
need to be made, making it perfect
for training rooms, boardrooms, and
classrooms.
A single-gang backbox and surround
is included or you can mount in a
double-gang surround with other
connectivity modules. You could even
mount into a Techconnect
2
Tilt in the
table!
A 3m DC tail which can be shortened
means easy routing of power cable
through trunking. Velcro is included
for fixing the power supply in place,
or a blank surround is available to
hide it in a standard double-gang UK
backbox.
42 x 71 x 40mm
63 grams
White
2 x Stereo inputs via removable
phoenix connectors
n
2 x 20w @ 8 ohms
n
Total Harmonic Distortion less than or
equal to 1% (20Hz~22kHz)
n
Frequency response (line in):
80Hz~22kHz(±2dB)
n
Signal to noise ratio (line in): more than or
equal to 98dB (A-weighted)
n
Rating input level/impedance: Line in
500mV/50k?
n
Power Supply 100-240vAC 50/60Hz, Max
1A, DC Output 12V 4A, DC Cable 3m
n
Power consumption (rating condition):
less than or equal to 40W
n
1 x Single-gang Backbox
n
1 x Single-gang Surround
n
2 x 150mm input cables
n
2 x Unshielded Speaker cable 5m long
n
1 x Euro Figure-8 Power cable 2m long
n
1 x UK Figure-8 Power cable 2m long
Manu code: TC2-AMP2 / Part code: 1872510
Manu code: TC2-AMP2+SP-1300B
Part code: 1703068
Manu code: TC2-AMP2+SP-1300W
Part code: 1703069
Manu code: TC2-AMP2+CS-1300
Part code: 1703070
“
“
DAVE SAYS...
With the new modular Techconnect
Control
2
the button layout and
labels can be changed to suit each
application. Whether it be for a small
installation or a large roll-out, using
this control device to standardise the
control interface results in confident
users and fewer support calls.
The module learns codes for up to
three AV devices. Press ‘ON’ once to
simultaneously drop the screen, turn
the projector, and turn the amplifier
on.
Use the remote control from your
equipment to program the module in
a few easy steps. The Control
2
has
increased processing and memory
power to cover a wider range of IR
protocols.
The codes from one Control
2
module
can be duplicated to other Control
2
modules.
A smaller long life 3-Volt lithium
battery is included or it can share
the power supply provided with a
Techconnect Amplifier
2
. This power
supply is also available as a spare.
A single-gang surround and
backbox is included or you can mount
it in a surround with other modules.
POWER:
The power buttons (top) are pre-set
to send up to three stored codes
each at the same time for turning all
equipment on or off with one press. It
will automatically send the projector’s
‘off’ code twice.
INPUT:
The input buttons (middle) can learn
up to four codes each, and can
broadcast in two ways: to suit your
application:
Sequential Example:
Press 1: Projector PC1 Input
Press 2: Projector PC2 Input
Press 3: Projector VID Input
Press 4: Projector S-VID Input
Toggle Example:
Press 1: Projector PC1 Input and
Amplifier Input 1
Press 2: Projector PC2 Input and
Amplifier Input 2
VOLUME:
The volume buttons (bottom) can only
learn one code each, but outputs that
code repeatedly if held down.
71 x 42 x 31mm
63 grams
White
Static: <= 5uA
Sending: <= 20mA
Copying: <= 10mA
n
26 x Interchangeable buttons
n
1 x Single-Gang Techconnect Backbox
n
1 x Single-Gang Techconnect Surround
n
1 x IR Blaster with 10m cable
n
2 x IR Blaster without cable
n
1 x 3V Lithium CR2450 Battery
Manu code: TC2-CTL2 / Part code: 1872511
Optional Power Supply:
Manu code: TC2-CTL2PWR
Part code: 1872512