9-1/2' x 8' Vinyl Storage Shed Model #S-9580-A S-9582-A S-9584-A Storage Shed Owner’s Manual 9-1/2' x 8' (2.90m x 2.44m) PLEASE READ OWNER’S MANUAL COMPLETELY BEFORE ASSEMBLING YOUR BUILDING. ALL STATED SIZES ARE NOMINAL DIMENSIONS.
Parts List Congratulations on your purchase of this Vision Vinyl Storage Building! As with any construction or assembly project, please exercise caution when using tools and equipment to install this structure. Be sure to read and follow the instructions contained within this manual prior to assembly. If you have any questions before, during or after assembly, please contact the Vision Help Line at 1-866-633-9970. We welcome your call and will be glad to assist you in any way we can.
Parts Location See parts list on previous page for parts description RP1 RGA Ridge Cap F512H01 FC1 Gable End Cap RGB FC1 RGB Gable End Cap RP1 FC1 RGA FC1 Outside Vents WP7 WP6 WP5 WP4 WP3 WP2 WP1 WP13 CNR WP12 Inside Vents F512G01 WP11 WP10 WP9 WP8 F512K04 F512K01 F512K05 CNR CNR F512G01 F512K05 Door Header F512K02 F512I01 F512K03 WP1 WP8 WP9 Aluminum Door Frame Right F512K02 F512K03 WP3 Aluminum Door Frame Left F512K05 CNR F512K01 WP2 F512K04 NOTE: Before assembly of
Parts Identification Corner Post Wall Panel Roof Panel Fascia Gable Ridge Cap Ridge Beam Roof Reinforcement Base Track Vent (Inside & Outside) Roof Fascia Cap Lintel (Upside Down) Slope Wall Cap Gable End Cap #8 x 1" Pan Head Screws (150) Hinge Screws (12) #8 x 3/4" Pan Head Screws (65) Door Handle (2) Door Latch (2) Door (2) Tools Required Materials Needed • Power drill with Phillips® (#2) or a #2 square bit • Carpenter’s square • Level • Rubber mallet • Hammer • Safety glasses • Gloves
Concrete Floor Option Concrete Floor Option You may decide to construct your Vision storage shed on a concrete foundation, in which case it is recommended that you engage the services of a concrete contractor. • Select a location that is free from ground water and provides suitable drainage, that can be leveled properly and affords ample room to erect the shed.
Wood Floor Option Wood Floor Option If you choose to construct your Vision storage shed on a wood foundation, follow these recommendations to achieve the best results. Use only treated lumber, as standard 2 x 4’s and plywood will deteriorate rapidly, compromising your building in a relatively short time. Avoid placing any wood components (even treated lumber) in direct contact with the ground. Either support the wood structure on blocks or preferably, pour and level a gravel base as a start to your project.
Assembly 144-1/2" 4-1 /2" CHECK 72-1/2" door opening dimension between front Base Tracks. /16" 14 Each Base Track piece has two different height sides. The higher side of the track is positioned on the inside and the lower side (where drain holes are located approximately every 12 inches) to the outside. Track pieces for the corners are bevel-cut so that matching the high sides and low sides of the track will be match up.
3 Panel Assembly – General Instructions Vision Shed Wall Panels, Roof Panels and Corner Posts make assembling your building easy. Each panel and post is engineered the same way: Integrated Vinyl Channel Locks are integrally molded the full length of the panels and are simply “snapped together,” locking the pieces securely to create incredibly sturdy walls and roof. Along each long vertical edge of the Wall Panels is either a DEEP or SHALLOW Channel lock.
5 Panel Assembly – Left Front Wall Locate the preassembled, left front wall section. To differentiate the left section from the right, hold both sections upright on the shed base. The left front wall (as seen from outside the shed) has the aluminum door frame preinstalled on the right side of the section. The top edge of this left wall panel section, which forms the roof peak, slopes down away from the door.
7 Panel Assembly – Remaining Walls Back wall Locate and arrange the back wall panels from shortest to the highest (peak) to create two separate half wall sections. Again, making sure the DEEP Channel locks face out, join the panels together as with previous assembly instructions. Insert into base track, joining the section to the corner post you already attached to the corner of the left side wall. Repeat with the second half back wall, making sure first, to affix a corner post to the back wall section.
10 Ridge Beam With an assistant holding one end of the ridge beam, position the front of the beam at the flat edge of the header peak and the back wall peak. It also may be necessary to stand on a ladder for this assembly step. Note the notches in the bottom section of the ridge beam. Carefully slide the notches over the inner and outer wall of the header panels making sure the opening in the bottom of the ridge beam engages over the center seam of the head wall.
Ridge Cap With both you and your assistant standing on ladders at each end of the roof, position the ridge cap over the ridge beam making sure each end is flush with the outer edge of the outermost roof panel. With the rubber mallet, strike the top of the ridge cap nearest the edge of the roof so that its tabs seat on the vertical member of the ridge beam. You’ll hear a characteristic click when it engages. Continue toward the center of the roof in a similar fashion.
16 Doors 16A Locate the left and right hand doors. The right hand door features a full length astragal door strike along one edge (Diagram 16A) which closes over the left hand door. Doors must be installed so that they open out from the shed. Install the right hand door first by aligning the top and bottom hinges with the predrilled holes in the aluminum frame of the door opening. Use the screws (Diagram 16B) provided.
18 Wall Vents 19 Insert and Fasten Screws to the Interior Components Locate the inner and outer vent covers for the two back wall vents. The inner vent cover has a screw hole near the top and bottom of the vent. The outer vent cover has no screw holes. Position the outer vent covers into the vent openings. Position the inner vent covers into the openings from inside the shed. Insert screws into the screw holes through the inner vent cover, engaging the outer vent cover. Tighten reasonably snug.
20 Affixing Hooks and Shelf Brackets Hooks, shelving and other storage devices can be installed on the walls of your Vision Vinyl Shed just as simply as in your garage. Screws or other threaded fasteners to affix hooks, hangers and shelving, should be inserted ONLY in the scored (indented) groove located 3/8" to the side of the seam created by the joint of two wall panels (See Figures 21A and 21B). 21A DO NOT INSERT SCREWS DIRECTLY IN THE JOINT BETWEEN TWO WALL PANELS.
