User Manual

Introduction
Thanks for choosing the Vision’s curtain control module of the home automation device.
This module is a Z-Wave™ enabled device (interoperable, two-way RF mesh networking
technology) and is fully compatible with any Z-Wave™ enabled network. Every mains
powered Z-Wave enabled device acts as a signal repeater and multiple devices result in
more possible transmission routes which helps eliminate “RF dead-sports”
Z-Wave™ enabled devices displaying the Z-Wave™ logo can also be used with it
regardless of the manufacturer, and ours can also be used in other manufacturer’s
Z-Wave™ enabled networks. Users easily control the curtain to open and close by sending
Z-Wave™ signal from Z-Wave™ Interface Controller. This module will send open/close
signal to the appliance that attached to this module by receiving Z-Wave™ signal from
controller or manually switch. Our special design the curtain not only can be opened and
closed but also can be stopped under the Multilevel Switch command on the controller.
This module also acts as repeater (supporting FLiRS devices).
Product Description and Specification
*** For indoor use only ***
Specification:
Package Content:
Protocol: Z-Wave™ (ZM3102N)
Frequency Range:
865.22MHz (ZW4101IN/ZW 4102 IN)
868.42MHz (ZW 4101EU/ZW 4102 EU)
869.00MHz (ZW 4101RU/ZW 4102 RU)
908.42MHz (ZW 4101US/ZW 4102 US)
916.00MHz (ZW 4101IS/ZW 4102 IS)
921.42MHz (Z W 4101BR/ZW 4102 BR)
920-928Mhz (ZW4101JP/ZW 4102 JP)
Operating Range: Up to 100 feet line of sight
Operating Temp.: -15°C~ 60°C (5°F ~140°F)
Operating Voltage: 12V
Current Consumption: 25mA
ZW4101 Signal Output:
OPEN output: -VE, 100mA (max)
CLOSE output: -VE, 100mA (max)
STOP output: -VE, 100mA (max)
ZW4102 Relay Output:
1pc
1pc
ZW 4101 or ZW 4102 Curtain Control
Module
Installation & Operation Manual
Relay Normal Output: 14VDc, 5A (max)
OPEN output: 14VDc, 5A (max)
CLOSE output: 14VDc, 5A (max)
STOP output: 14VDc, 5A (max)
Installation
Notice: If you are installing the entire Z-Wave™ system for the first time, please refer to the installation
guide of Z-Wave™ Interface Controller before installing ZW 4101 / ZW 4102 Curtain Module.
1. Connect the following wires with curtain’s manual switch or switch’s signal. User can skip switch if
it is not necessary.
Wire Color
ZW 4101
ZW 4102
RED
POWER
POWER
BLACK
GROUND
GROUND
WHITE
OPEN SIGNAL OUTPUT
OPEN RELAY-COM
WHITE/BLACK
X
OPEN RELAY-NO
GRAY
CLOSE SIGNAL OUTPUT
CLOSE RELAY-COM
GRAY/BLACK
X
CLOSE RELAY-NO
BROWN
STOP SIGNAL OUTPUT
STOP RELAY-COM
BROWN/RED
X
STOP RELAY-NO
2. For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into“inclusion”
mode, and following its instruction to add the ZW 4101 / ZW4102 to your controller. To get in the
“inclusion” mode, the distance between module and controller is suggested to be in one meter.
Press the program switch on the module once to be included.
For “Exclusion” from (removing from) a network: Put the Z-Wave™ Interface Controller into
“exclusion” mode, and following its instruction to delete the ZW 4101 / ZW4102 from your
controller. Press the program switch on the module once to be excluded.
Note: LED setting light will flash (RED) continuously in Exclusion condition.
3. Z-Wave™ Command Class
COMMAND_CLASS_BASIC (Mapping COMMAND_CLASS_SWITCH_MULTILEVEL)
COMMAND_CLASS_CONFIGURATION
COMMAND_CLASS_MANUFACTURER_SPECIFIC
COMMAND_CLASS_SWITCH_BINARY
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
COMMAND_CLASS_VERSION
4. Under the basic command, Status of “ON” (Basic Set,0xFF), Curtain to be opened. Status of
“OFF” (Basic Set,0x00), Curtain to be closed.
5. Configuration command class: Parameter 1: Up output time, 1 byte value=1~255 seconds;
Parameter 2: Stop output time, 1 byte value=1~255 seconds; Parameter 3: Down output time, 1
byte value=1~255 seconds.
6. Keeping press program switch for 5 seconds, curtain will reset back to factory preset
-1-
-2-