User's Manual

ManualsBrandsVision Automobile Electronics Industrial ManualsElectronicsZ-WAVE USB Dongle

Introduction

Thanks for choosing Vision’s Z-Wave USB dongle of the home automation device. This

USB dongle is a Z-Wave

enabled device (interoperable, two-way RF mesh networking

technology) and is fully compatible with any Z-Wave

enabled network. Every main

powered Z-Wave

enabled device acts as a signal repeater and multiple devices result

in more possible transmission routes which helps eliminate “RF dead-sport”. Z-Wave

enabled devices displaying the Z-Wave

logo can also be used with it regardless of the

manufacturer, and ours can also be used in other manufacturer’s Z-Wave

enabled

networks. This USB dongle which compliant to ZDK6.XX and above exports Z-Wave

Serial API through a USB CDC/ACM compliant connection with a USB A Plug. A

PC/Notebook which runs Z-Wave software can control Z-Wave Home Area Network

through this USB dongle.

Product Description and Specification

Specification:

Package Content:

Protocol: Z-Wave

(ZM4101N)

Frequency Range:

908.42MHz (ZU1401US)

868.42MHz (ZU1401EU)

921.42MHz (ZU1401BR)

920-928 MHz (ZU1401JP)

865.22MHz (ZU1401IN)

Operating Range.: Up to 100 feet line of sight

Operating Temp.: -15°C~ 60°C (5°F~140°F)

1pc ZU1401 USB Dongle

1pc User Manual

Operation

If you are installing the entire Z-Wave

system for the first time, please refer to the

installation guide of Z-Wave

Interface Controller before installing ZU1401 USB dongle

As the device export a USB CDC/ACM compliant interface, it appears as a serial port

which uses the existing standard driver on most of popular PC/Notebook operating

systems.

1. Simply plug this USB dongle in PC/Notebook USB port.

2. System requirement：

- Windows 2000/XP/Vista/7 32&64 bit

UZB.INF is provided that reuses the standard Windows usbser.sys or usbser64.sys driver

- Linux kernel 2.6.24+

The device appears as “/dev/ttyACMxx” where xxx is the tty number assigned by the OS

- MAC OS X 6.4

The device appears as “/dev/tty.usbmodemxxx” where xxx is the tty number assigned by the OS

3. Please download USB driver software from below location to install this Z-Wave

USB dongle.

 http://www.visionsecurity.com.tw/ha_files_3.html

This equipment has been followed to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment

generates uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try and correct the interferene by one of the following measures:

- Reorient or relocate the receiving antenna,

- Increase the separation between the equipment and receiver,

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undersired

operation.

FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate this equipment.

Vision Guarantees that every USB Dongle is free from physical defects in material and workmanship

under normal use for one year from the date of purchase. If the product proves defective during this

one-year warranty period, Vision will replace it free of charge. Vision does not issue any refunds. This

warranty is extended to the original end user purchase only and is not transferable. This warranty

does not apply to: (1) damage to units caused by accident, dropping or abuse in handling, or any

negligent use; (2) units which have been subject to unauthorized repair, taken apart, or otherwise

modified; (3) units not used in accordance with instruction; (4) damages exceeding the cost of the

product; (5) transit damage, initial installation costs, removal cost, or reinstallation cost.

For information on addional devices, plesae visit us at

www.visionsecurity.com.tw

Federal Communications Commission Statement

Limited Warranty

-1-

-2-