User's Manual
11. PowerLevel Control: Using “PowerLevel Set” to set up the RF strength. And using
“PowerLevel Test Node Set” to tests the RF signal of specific node.
12. Support “Firmware Update” After firmware update and before using the smoke detector, please
exclude the unit from the gateway first and re-include it back.
Federal Communications Commission Statement
This equipment has been followed to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try and correct the interferene by one of the following measures:
-- Reorient or relocate the receiving antenna,
-- Increase the separation between the equipment and receiver,
-- Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undersired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
Limited Warranty
Vision Guarantees that every wireless smoke detector is free from physical defects in material and workmanship under
normal use for one year from the date of purchase. If the product proves defective during this one-year warranty period,
Vision will replace it free of charge. Vision does not issue any refunds. This warranty is extended to the original end
user purchase only and is not transferable. This warranty does not apply to: (1) damage to units caused by accident,
dropping or abuse in handling, or any negligent use; (2) units which have been subject to unauthorized repair, opened,
taken apart, or otherwise modified; (3) units not used in accordance with instruction; (4) damages exceeding the cost
of the product; (5) transit damage, initial installation costs, removal cost, or reinstallation cost.
For information on addional devices, plesae visit us at www.visionsecurity.com.tw
Introduction
Thanks for choosing the Vision’s wireless smoke detector of the home security device. This detector is a Z-Wave™
enabled device (interoperable, two-way RF mesh networking technology) and is fully compatible with any Z-Wave™
enabled network. Every mains powered Z-Wave™ enabled device acts as a signal repeater and multiple devices
result in more possible transmission routes which helps eliminate “RF dead-sports”.
Z-Wave™ enabled devices displaying the Z-Wave™ logo can also be used with it regardless of the manufacturer, and
ours can also be used in other manufacturer’s Z-Wave™ enabled networks. This detector is designed to sense smoke
that comes into the detector chamber and send Z-Wave™ signal when the detector detects a certain density of smoke
then the horn of smoke detector will sound.
Product Description and Specification
*** For indoor use only ***
Specification:
Package Content:
Protocol: Z-Wave™ (ZM5202N)
1pc
ZS 6101-5/6102-5 Smoke
Detector
Frequency Range:
1pc
Bracket Holder
865.22MHz (ZS6101/6102IN-5)
1pc
Plastic Anchor
868.42MHz (ZS6101/6102EU-5)
2pcs
Screw
869.00MHz (ZS6101/6102RU-5)
1pc
CR17450E-R Lithium Battery
908.42MHz (ZS6101/6102US-5)
or
(ZS6102-support FLiRs version)
920~928MHz (ZS6101/6102JP-5)
1pc
CR123A Lithium Battery
921.42MHz (ZS6101/6102BR-5)
919~924MHz (ZS6101/6102KR-5)
916.00 MHz (ZS6101/6102IL-5)
868.10MHz (ZS6101/6102MY-5)
919.80MHz (ZS6101/6102HK-5)
1pc
(ZS6101-w/o FLiRs version)
Installation & Operation
Manual
Operating Range: Up to 100 feet line of sight
Operation Temperature: 0℃~49℃
Alarm Audibility: 85dB/3m
Relative Humidity: 10~95%
Size: 120mm diameter x 5.3mm depth
Battery: 3V Lithium Battery
Sensitivity: Meet with both UL217 and EN14604 standard
Z-Wave™ Command Classes:
COMMAND_CLASS_ZWAVEPLUS_INFO
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_BATTERY
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
COMMAND_CLASS_NOTIFICATION_V4
COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_SWITCH_BINARY
COMMAND_CLASS_VERSION_V2
COMMAND_CLASS_WAKE_UP
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2
*Note: WAKE_UP command for ZS6101 only
-4-
Tamper Switch
-1-