User's Manual
Introduction
Thanks for choosing the Vision’s wireless PIR motion sensor of the home security device.
This sensor is a Z-Wave
TM
enabled device (interoperable, two-way RF mesh networking
technology) and is fully compatible with any Z-Wave
TM
enabled network and it’s security
framework. Every mains powered Z-Wave
TM
enabled device acts as a signal repeater and
multiple devices result in more possible transmission routes which helps eliminate “RF
dead-spots”.
Z-Wave
TM
enabled device displaying the Z-Wave
TM
logo can also be used with it
regardless of the manufacturer, and ours can also be used in other manufacturer’s Z-Wave
TM
enabled networks. This sensor monitors movement, and send Z-Wave
TM
signal when
movement is detected inside the building. With Temperature sensor built inside, it will
send the signal out when temperature changed. When the device is secure included into
Z-Wave network, above communication will be encrypted.
Product Description and Specification
*** For indoor use only ***
Specification:
Package Content:
Protocol: Z-Wave™ (ZM5202)
Frequency Range:
865.22MHz (ZP3102IN-5)
868.10MHz (ZP3102MY-5)
868.42MHz (ZP3102EU-5)
869.00MHz (ZP3102RU-5)
908.42MHz (ZP3102US-5)
916.00MHz (ZP3102IL-5)
919.70MHz (ZP3102KR-5)
919.80MHz (ZP3102HK-5)
920.00MHz~928.00MHz (ZP3102JP-5)
921.42MHz (ZP3102BR-5)
Operating Range: Up to 100 feet line of sight
Operating Temp.: -15°C~ 40°C (5°F~104°F)
Battery: Panasonic CR123A * 1PC
1pc
1pc
1pc
1pc
ZP 3102 sensor
Adhesive tape for sensor
CR123A Lithium Battery
Installation & Operation Manual
Z-Wave Command Classes:
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_BASIC
COMMAND_CLASS_BATTERY
COMMAND_CLASS_CONFIGURATION
COMMAND_CLASS_DEVICE_RESET_LOCALLY
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
COMMAND_CLASS_NOTIFICATION_V4 (mapping _COMMAND_CLASS_BASIC)
COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SENSOR_MULTILEVEL_V5
COMMAND_CLASS_VERSION_V2
COMMAND_CLASS_WAKE_UP_V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Installation
Notice: If you are installing the entire Z-Wave
TM
system for the first time, please refer to the
installation guide of Z-Wave
TM
Interface Controller before installing ZP3102.
1. Release cover tab to open the cover and insert a CR123A battery into the battery
compartment and LED will start to flash slowly, which means the sensor has not been
“inclusion” yet.
2. Close the cover back to sensor.
3. For “Inclusion (Auto-Inclusion)” in (adding to) a network: To add the ZP3102 to your
Z-Wave network (inclusion), place your Z-Wave primary controller into inclusion mode
and the distance between sensor and controller is suggested to be in one meter.
Press the Program Switch of ZP3102 for sending the NIF. After sending NIF, Z-Wave
will send the auto inclusion, otherwise, ZP3102 will go to sleep after 10 seconds. (P.S.:
Press the Program Switch to send NIF again for inclusion if the auto inclusion did not
success. The ZP3102 will go to sleep after 20 seconds if the inclusion did not work).
For “Exclusion” from (removing from) a network: To remove the ZP3102 from your
Z-Wave network (exclusion), place your Z-Wave primary controller into “exclusion”
mode, and following its instruction to delete the ZP3102 to your controller. Press the
Program Switch of ZP3102 once to be excluded. The LED
on the ZP3102 should start
to flash.
For “Association”: removing the cover of the ZP3102 to get into “Awake” mode, then
put the Z-Wave
TM
Interface Controller into “association”, and following its instruction to
associate the ZP3102 with other device. Close the cover back after “association”
done, afterward the ZP3102 will get into “Sleep” mode for power saving. Support one
association group (5 nodes).
-2-
-1-