User's Manual

Introduction
Thanks for choosing the Vision’s lighting control of the home automation device. This
module is a Z-Wave
TM
enabled device (interoperable, two-way RF mesh networking
technology) and is fully compatible with any Z-Wave
TM
enabled network. Every main
powered Z-Wave
TM
enabled device acts as a signal repeater and multiple devices result
in more possible transmission routes which helps eliminate “RF dead-sport”.
Z-Wave
TM
enabled devices displaying the Z-Wave
TM
logo can also be used with it
regardless of the manufacturer, and ours can also be used in other manufacturer’s
Z-wave
TM
enabled networks. This module will send dimmer (ZL 7101) or On/Off (ZL
7201) signal to the appliance that attached to this module by receiving Z-Wave
TM
signal
from controller or manually switch. With special design, this module won’t interfere the
other power outlet when plug into the AC outlet. This module also acts as repeater
(supporting FLiRS).
Product Description and Specification
* For indoor use *
Specification:
Package Content:
Protocol: Z-Wave
TM
(ZM3102N/ZM4102AH)
Frequency Range:
908.42MHz (ZL 7101 / ZL 7201 US)
868.42MHz (ZL 7101 / ZL 7201 CN)
920-928 MHz (ZL 7101 / ZL 7201 JP)
Operating Range: Up to 100 feet line of sight
Operating Temp.: -15°C~ 60°C (5°F~140°F)
Operating Voltage:
110VAC (for ZL7101/ZL7201US)
100~240VAC (for ZL7101/ZL7201CN & JP)
-1-
1pc ZL 7101, Plug-in Type Dimmer
Module
Or
ZL 7201, Plug-in Type Appliance
On/Off Module
1pc User Manual
For
ZL7101
only
Max. Load: 300W for Resistive Load
For ZL7201 only
Max. Load: 600 W for Incandescent Load
1800 W for Resistive Load
Relay: Load 10A/277 VAC
Z-Wave™
™™
™ Command Class:
COMMAND_CLASS_MANUFACTURER_SPECIFIC
COMMAND_CLASS_PROTECTION
COMMAND_CLASS_SWITCH_ALL
COMMAND_CLASS_SWITCH_BINARY (for ZL 7201 only)
COMMAND_CLASS_SWITCH_MULTILEVEL (for ZL 7101 only)
COMMAND_CLASS_VERSION
Operation
If you are installing the entire Z-Wave
TM
system for the first time, please refer to the
installation guide of Z-Wave
TM
Interface Controller before installing ZL 7101 & ZL 7201.
-1-
1. For “Inclusion” in (adding to) a network: Put the Z-Wave
TM
Interface Controller into
“inclusion” mode, and following its instruction to add the ZL 7101 or ZL 7201 into
your controller. To get in the “Inclusion” mode, the distance between ZL 7101 or ZL
7201 and controller is suggested to be in one meter. Press program button once to
be included. Noted: for ZL71017/ZL7201 JP, to get included by power up, no need
to press program button
For “Exclusion” from (removing from) a network: Set up the Z-Wave
TM
Interface
Controller into “exclusion” mode, and following its instruction to delete the ZL 7101
or ZL 7201 from your controller. Press program button to be excluded.
2. Manually turn the connected lighting On/Off by your controller or pressing the
program button. This is toggle switch. If the light is OFF, pressing the button
turns the light ON and vice versa.
3. For ZL 7101 only: Adjust the brightness level of the connected lighting by your
controller or pressing and holding the program button. Release the button when
the desired level is attained. This is a toggle function. The lighting will dim until the
minimum level is attained or the button is released. The next time the button is
pressed and held, the level will increase until the maximum level is attained or the
button is released.
-2-