Datasheet
TSOP582.., TSOP584..
www.vishay.com
Vishay Semiconductors
Rev. 1.6, 12-Apr-18
2
Document Number: 82461
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
BLOCK DIAGRAM APPLICATION CIRCUIT
Note
• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability
TYPICAL CHARACTERISTICS (T
amb
= 25 °C, unless otherwise specified)
Fig. 1 - Output Active Low Fig. 2 - Pulse Length and Sensitivity in Dark Ambient
33 kΩ
2
3
1
Demo-
pass
AGCInput
PIN
Band
dulator
Control circuit
16833_14
C
1
IR receiver
GND
Circuit
μC
R
1
+ V
S
GND
Transmitter
with
TSALxxxx
V
S
V
O
17170-11
OUT
R
1
and C
1
recommended to reduce supply ripple for V
S
< 2.8 V
ABSOLUTE MAXIMUM RATINGS
PARAMETER TEST CONDITION SYMBOL VALUE UNIT
Supply voltage V
S
-0.3 to +6 V
Supply current I
S
5mA
Output voltage V
O
-0.3 to 5.5 V
Voltage at output to supply V
S
- V
O
-0.3 to (V
S
+ 0.3) V
Output current I
O
5mA
Junction temperature T
j
100 °C
Storage temperature range T
stg
-25 to +85 °C
Operating temperature range T
amb
-25 to +85 °C
Power consumption T
amb
≤ 85 °C P
tot
10 mW
Soldering temperature t ≤ 10 s, 1 mm from case T
sd
260 °C
ELECTRICAL AND OPTICAL CHARACTERISTICS (T
amb
= 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
Supply voltage V
S
2.5 - 5.5 V
Supply current
V
S
= 5 V, E
v
= 0 I
SD
0.55 0.7 0.9 mA
E
v
= 40 klx, sunlight I
SH
-0.8-mA
Transmission distance
E
v
= 0, IR diode TSAL6200,
I
F
= 250 mA, test signal see Fig. 1
d-40-m
Output voltage low I
OSL
= 0.5 mA, E
e
= 0.7 mW/m
2
, test signal see Fig. 1 V
OSL
- - 100 mV
Minimum irradiance
Pulse width tolerance:
t
pi
- 5/f
o
< t
po
< t
pi
+ 6/f
o,
test signal see Fig. 1
E
e min.
-0.20.4mW/m
2
Maximum irradiance t
pi
- 5/f
o
< t
po
< t
pi
+ 6/f
o
, test signal see Fig. 1 E
e max.
50 - - W/m
2
Directivity Angle of half transmission distance ϕ
1/2
-± 45-deg
16110
E
e
T
t
pi
*
t
* t
pi
10/f
0
is recommended for optimal function
V
O
V
OH
V
OL
t
Optical Test Signal
(IR diode TSAL6200, I
F
= 0.4 A, 30 pulses, f = f
0
, t = 10 ms)
Output Signal
t
d
1)
t
po
2)
1)
7/f
0
< t
d
< 15/f
0
2)
t
pi
- 5/f
0
< t
po
< t
pi
+ 6/f
0
1.0
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
0.1 1 10 10
2
10
3
10
4
E
e
- Irradiance (mW/m
2
)
t
po
- Output Pulse Width (ms)
Input Burst Length
Output Pulse Width
λ = 950 nm,
Optical Test Signal, Fig.1
0
0.1