Datasheet

ManualsBrandsVishay ManualsCapacitorsTantalum Capacitor with Polymer Cathode 220uF ±20% 16V

T52

www.vishay.com

Vishay

Revision: 15-Apr-2019

Document Number: 40216

For technical questions, contact: polytech@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

vPolyTan

Polymer Surface Mount Chip Capacitors,

Low Profile, Leadframeless Molded Type

DESIGN SUPPORT TOOLS AVAILABLE

PERFORMANCE / ELECTRICAL

CHARACTERISTICS

Operating Temperature: -55 °C to +105 °C

Capacitance Range: 47 μF to 470 μF

Capacitance Tolerance: ± 20 %

Voltage Rating: 10 V

to 35 V

FEATURES

• Ultra low ESR

• 100 % surge current tested

• Accelerated voltage conditioning

• High ripple current capability

• Stable capacitance in operating temperature

range

• Better capacitance stability vs. frequency

• No wear out effect

• Molded case 7360, 7343 EIA size

• Lead (Pb)-free L-shaped face-down terminations

• 12 mm tape and reel packaging available per EIA-481

standard

• Material categorization: for definitions of compliance

please see www.vishay.com/doc?99912

APPLICATIONS

• Decoupling, smoothing, filtering

• Bulk energy storage in Solid State Drives (SSD)

• Infrastructure equipment

• Storage and networking

• Computer motherboards

• Smartphones and tablets

3D Models

Models

Calculators

ORDERING INFORMATION

T52 M1 337 M 016 C 0055

TYPE CASE

CODE

CAPACITANCE CAPACITANCE

TOLERANCE

DC VOLTAGE

RATING

TERMINATION /

PACKAGING

ESR

See

Ratings

and

Case

Codes

table.

This is expressed in

picofarads. The first

two digits are the

significant figures.

The third is the

number of zeros

to follow.

M = ± 20 % This is expressed

in volts. To

complete the

three-digit block,

zeros precede the

voltage rating.

A decimal point is

indicated by an “R”

(6R3 = 6.3 V)

C = 100 % tin, 7" reel Maximum

100 kHz ESR

in m

DIMENSIONS in inches [millimeters]

CASE CODE E5

CASE CODE EIA SIZE H (MAX.) L W P1 P2 (REF.) C B (REF.) D (REF.)

E5 7343-15

0.059

[1.5]

0.287 ± 0.012

[7.3 ± 0.3]

0.169 ± 0.012

[4.3 ± 0.3]

0.051 ± 0.008

[1.3 ± 0.2]

0.191

[4.85]

0.094 ± 0.008

[2.4 ± 0.2]

Anode

termination

Cathode

termination

Anode polarity mark

0.25 Ref.

0.05 Ref.

View A

Both sides typical

P1 P1

Summary of content (15 pages)

PAGE 1
T52 www.vishay.com Vishay vPolyTanTM Polymer Surface Mount Chip Capacitors, Low Profile, Leadframeless Molded Type FEATURES • • • • • • • • • • DESIGN SUPPORT TOOLS AVAILABLE 3D 3D • Models 3D Models Calculators PERFORMANCE / ELECTRICAL CHARACTERISTICS Ultra low ESR 100 % surge current tested Accelerated voltage conditioning High ripple current capability Stable capacitance in operating temperature range Better capacitance stability vs.
PAGE 2
T52 www.vishay.com Vishay DIMENSIONS in inches [millimeters] CASE CODE M1 Anode polarity mark View A Both sides typical L P1 P2 P1 CASE CODE EIA SIZE H (MAX.) 7360-20 0.079 [2.0] 0.25 Ref. H D M1 Cathode termination A W C B A 0.05 Ref. Anode termination L W P1 P2 (REF.) C B (REF.) D (REF.) 0.138 [3.5] 0.161 ± 0.008 [4.1 ± 0.2] 0.079 [2.0] 0.020 [0.5] 0.287 ± 0.012 0.236 ± 0.012 0.075 ± 0.008 [7.3 ± 0.3] [6.0 ± 0.3] [1.9 ± 0.
PAGE 3
T52 www.vishay.com Vishay STANDARD RATINGS CAPACITANCE CASE (μF) CODE PART NUMBER MAX. DCL AT +25 °C (μA) MAX. DF AT +25 °C 120 Hz (%) MAX. ESR AT +25 °C 100 kHz (m) HIGH TEMPERATURE MAX. LOAD RIPPLE, 100 kHz IRMS TEMPERATURE TIME (A) (°C) (h) MSL 10 VDC AT +105 °C 220 M1 T52M1227M010C0055 220 330 M1 T52M1337M010C0055 330 10 55 1.732 105 2000 3 10 55 1.732 105 2000 3 16 VDC AT +105 °C 150 E5 (1) T52E5157M016C0055 240 10 55 1.
PAGE 4
T52 www.vishay.com Vishay PERFORMANCE CHARACTERISTICS ITEM CONDITION Life test at +105 °C 2000 h (according to Standard Ratings table) application of rated voltage at 105 °C, MIL-STD-202 method 108 Shelf life test at +105 °C 2000 h no voltage applied at 105 °C, MIL-STD-202 method 108 Humidity tests At 60 °C / 90 % RH 500 h, no voltage applied Stability at low and high temperatures -55 °C 25 °C 85 °C 105 °C Surge voltage 85 °C, 1000 successive test cycles at 1.
PAGE 5
Polymer Guide www.vishay.com Vishay Guide for Tantalum Solid Electrolyte Chip Capacitors with Polymer Cathode INTRODUCTION Tantalum electrolytic capacitors are the preferred choice in applications where volumetric efficiency, stable electrical parameters, high reliability, and long service life are primary considerations.
PAGE 6
Polymer Guide www.vishay.com Vishay SOLID ELECTROLYTE POLYMER TANTALUM CAPACITORS Solid electrolyte polymer capacitors utilize sintered tantalum pellets as anodes. Tantalum pentoxide dielectric layer is formed on the entire surface of anode, which is further impregnated with highly conductive polymer as cathode system.
PAGE 7
Polymer Guide www.vishay.
PAGE 8
Polymer Guide www.vishay.com Vishay POLYMER CAPACITORS - MOLDED CASE SERIES T55 PRODUCT IMAGE VPolyTanTM, molded case, high performance polymer High performance -55 °C to +105 °C 3.3 μF to 1000 μF 2.5 V to 63 V ± 20 % 0.
PAGE 9
Polymer Guide www.vishay.com Vishay MOLDED CAPACITORS, T55 TYPE PLASTIC TAPE AND REEL PACKAGING DIMENSIONS in millimeters E A B C Label D W TAPE WIDTH A+0/-3 B+1/0 C ± 0.2 D ± 0.5 E ± 0.5 W ± 0.3 8 12 Ø 180 Ø 60 Ø 13 Ø 21 2.0 9.0 13.0 Note • A reel diameter of 330 mm is also applicable PLASTIC TAPE SIZE DIMENSIONS in millimeters Pocket Perforation E Ø 1.5 + 0.10 W B F A P1 t Direction of tape flow 4.0 ± 0.1 2.0 ± 0.
PAGE 10
Polymer Guide www.vishay.com Vishay LEADFRAMELESS MOLDED CAPACITORS, ALL TYPES PLASTIC TAPE AND REEL PACKAGING in inches [millimeters] 0.157 ± 0.004 [4.0 ± 0.10] Tape thickness Deformation between embossments 0.014 [0.35] max. 0.059 + 0.004 - 0.0 [1.5 + 0.10 - 0.0] Top cover tape B1 (max.) (6) 10 pitches cumulative tolerance on tape ± 0.008 [0.200] Embossment 0.079 ± 0.002 0.069 ± 0.004 [2.0 ± 0.05] [1.75 ± 0.10] A0 K0 0.030 [0.75] min. (3) B0 0.030 [0.75] min.
PAGE 11
Polymer Guide www.vishay.com Vishay CARRIER TAPE DIMENSIONS in inches [millimeters] CASE CODE TAPE SIZE B1 (MAX.) (1) D1 (MIN.) F K0 (MAX.) P1 W 0.071 [1.8] 0.315 ± 0.004 [8.0 ± 0.10] 0.476 ± 0.008 [12.1 ± 0.20] E5 12 mm 0.329 [8.35] 0.059 [1.5] 0.217 ± 0.002 [5.50 ± 0.05] MM (2) 8 mm 0.075 [1.91] 0.02 [0.5] 0.138 [3.5] 0.043 [1.10] 0.157 [4.0] 0.315 [8.0] M1 12 mm 0.32 [8.2] 0.059 [1.5] 0.217 ± 0.002 [5.5 ± 0.05] 0.094 [2.39] 0.315 ± 0.04 [8.0 ± 1.0] 0.472 + 0.012 / - 0.
PAGE 12
Polymer Guide www.vishay.com Vishay PACKING AND STORAGE Polymer capacitors meet moisture sensitivity level rating (MSL) of 3 or 4 as specified in IPC/JEDEC® J-STD-020 and are dry packaged in moisture barrier bags (MBB) per J-STD-033. MSL for each particular family is defined in the datasheet - either in “Features” section or “Standard Ratings” table. Level 3 specifies a floor life (out of bag) of 168 hours and level 4 specifies a floor life of 72 hours at 30 °C maximum and 60 % relative humidity (RH).
PAGE 13
Polymer Guide www.vishay.com Vishay MOLDED CAPACITORS, T55 TYPE PAD DIMENSIONS in millimeters L X Capacitor Pattern Y W G Z CAPACITOR SIZE PAD DIMENSIONS CASE / DIMENSIONS L W G (max.) Z (min.) X (min.) Y (Ref.) J 1.6 0.8 0.7 2.5 1.0 0.9 P 2.0 1.25 0.5 2.6 1.2 1.05 A 3.2 1.6 1.1 3.8 1.5 1.35 T/B 3.5 2.8 1.4 4.1 2.7 1.35 Z/V/D 7.3 4.3 4.1 8.2 2.9 2.
PAGE 14
Polymer Guide www.vishay.com Vishay GUIDE TO APPLICATION 1. AC Ripple Current: the maximum allowable ripple current shall be determined from the formula: I R MS = 4. Reverse Voltage: the capacitors are not intended for use with reverse voltage applied. However, they are capable of withstanding momentary reverse voltage peaks, which must not exceed the following values: At 25 °C: 10 % of the rated voltage or 1 V, whichever is smaller. At 85 °C: 5 % of the rated voltage or 0.5 V, whichever is smaller.
PAGE 15
Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product.