Datasheet

RCS e3
www.vishay.com
Vishay
Revision: 07-Mar-2019
7
Document Number: 20065
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Note
(1)
The quoted IEC standards are also released as EN standards with the same number and identical contents
4.37 67 (Cy)
Damp heat, steady state,
accelerated
(85 ± 2) °C; (85 ± 5) % RH
U = 100 V;
1000 h
± (1 % R + 0.05 )± (2 % R + 0.1 )
4.23 - Climatic sequence:
± (1 % R + 0.05 )± (2 % R + 0.1 )
4.23.2 2 (Bb) Dry heat 125 °C; 16 h
4.23.3 30 (Db) Damp 55 °C; 24 h; 90 % RH; 1 cycle
4.23.4 1 (Ab) Cold -55 °C; 2 h
4.23.5 13 (M) Low air pressure 8.5 kPa; 2 h; (25 ± 10) °C
4.23.6 30 (Db) Damp heat, cyclic
55 °C; 24 h;
90 % RH; 5 cycles
4.23.7 - DC load U = U
max.
; 1 min
- 1 (Aa) Cold -55 °C; 2 h ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 )
4.19 14 (Na)
Rapid change
of temperature
30 min. at -55 °C and
30 min. at 125 °C
1000 cycles
± (1 % R + 0.05 )
no visible damage
4.13 - Short time overload
U = 2.5 x 2 x U
max.
;
whichever is the less severe; 5 s
± (2 % R + 0.05 )
4.27 -
Single pulse
high voltage overload
Severity no. 4:
U = 10 x
or U = 2 x U
max.;
whichever is the less severe;
10 pulses 10 μs / 700 μs
± (1 % R + 0.05 )
no visible damage
4.39 - Periodic electric overload
U = or
U = 2 x U
max.;
whichever is the less severe;
0.1 s on; 2.5 s off;
1000 cycles
± (1 % R + 0.05 )
no visible damage
4.38 -
Electrostatic discharge
(human body model)
IEC 61340-3-1
(1)
;
3 positive + 3 negative discharges;
ESD voltage according to the size
± (1 % R + 0.05 )
4.22 6 (Fc) Vibration
Endurance by sweeping;
10 Hz to 2000 Hz;
no resonance;
amplitude 1.5 mm or 200 m/s
2
;
7.5 h
± (0.25 % R + 0.05 )
no visible damage
± (0.5 % R + 0.05 )
no visible damage
4.17 58 (Td) Solderability
Solder bath method,
SnPb40; non-activated flux
(235 ± 5) °C; (2 ± 0.2) s
Good tinning ( 95 % covered);
no visible damage
Solder bath method,
Sn96.5Ag3Cu0.5;
non-activated flux
(245 ± 5) °C; (3 ± 0.3) s
4.18 58 (Td)
Resistance to
soldering heat
Soldering bath method;
(260 ± 5) °C; (10 ± 1) s
± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 )
4.29 45 (XA)
Component solvent
resistance
Isopropyl alcohol +50 °C;
method 2
No visible damage
4.32 21 (Ue
3
)
Shear
(adhesion)
RCS0402 e3: 9 N
RCS0603 e3 and RCS0805 e3: 17.7 N
No visible damage
4.33 21 (Ue
1
) Substrate bending Depth 2 mm; 3 times
± (0.25 % R + 0.05 )
no visible damage,
no open circuit in bent position
4.7 - Voltage proof U = 1.4 x U
ins
; 60 s No flashover or breakdown
4.35 -
Flammability,
needle flame test
IEC 60695-11-5
(1)
;
10 s
No burning after 30 s
TEST PROCEDURES AND REQUIREMENTS
EN
60115-1
CLAUSE
IEC
60082-2
(1)
TEST
METHOD
TEST
PROCEDURE
REQUIREMENTS PERMISSIBLE
CHANGE (R)
STABILITY CLASS 1
OR BETTER
STABILITY CLASS 2
OR BETTER
Stability for product types:
1 to 10 M
RCS e3
0.1 x P
85
x R
P
70
x R
P
70
x R
P
70
x R
15 x P
70
x R