Datasheet

ManualsBrandsVISHAY ManualsFETsIRFU9110PBF, MOSFET

IRFR9110, IRFU9110, SiHFR9110, SiHFU9110

www.vishay.com

Vishay Siliconix

S13-0168-Rev. D, 04-Feb-13

Document Number: 91279

For technical questions, contact: hvm@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Power MOSFET

FEATURES

• Dynamic dV/dt Rating

• Repetitive Avalanche Rated

• Surface Mount (IRFR9110, SiHFR9110)

• Straight Lead (IRFU9110, SiHFU9110)

• Available in Tape and Reel

•P-Channel

• Fast Switching

• Material categorization: For definitions of compliance

please see www.vishay.com/doc?99912

DESCRIPTION

Third generation power MOSFETs from Vishay provide the

designer with the best combination of fast switching,

ruggedized device design, low on-resistance and

cost-effictiveness.

The DPAK is designed for surface mounting using vapor

phase, infrared, or wave soldering techniques. The straight

lead version (IRFU, SiHFU Series) is for through-hole

mounting applications. Power dissipation levels up to 1.5 W

are possible in typical surface mount applications.

Note

a. See device orientation.

Notes

a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11).

b. V

= - 25 V, starting T

= 25 °C, L = 21 mH, R

= 25 , I

= - 3.1 A (see fig. 12).

c. I

 - 4.0 A, dI/dt  75 A/μs, V

 V

, T

 150 °C.

d. 1.6 mm from case.

e. When mounted on 1" square PCB (FR-4 or G-10 material).

PRODUCT SUMMARY

(V) - 100

DS(on)

()V

= - 10 V 1.2

(Max.) (nC) 8.7

(nC) 2.2

(nC) 4.1

Configuration Single

P-Channel MOSFET

DPAK

(TO-252)

IPAK

(TO-251)

ORDERING INFORMATION

Package DPAK (TO-252) DPAK (TO-252) DPAK (TO-252) IPAK (TO-251)

Lead (Pb)-free and Halogen-free SiHFR9110-GE3 SiHFR9110TRL-GE3 SiHFR9110TR-GE3 SiHFU9110-GE3

Lead (Pb)-free

IRFR9110PbF IRFR9110TRLPbF

IRFR9110TRPbF

IRFU9110PbF

SiHFR9110-E3 SiHFR9110TL-E3

SiHFR9110T-E3

SiHFU9110-E3

ABSOLUTE MAXIMUM RATINGS (T

= 25 °C, unless otherwise noted)

PARAMETER SYMBOL LIMIT UNIT

Drain-Source Voltage V

- 100

Gate-Source Voltage V

± 20

Continuous Drain Current V

at - 10 V

= 25 °C

- 3.1

= 100 °C - 2.0

Pulsed Drain Current

- 12

Linear Derating Factor 0.20

W/°C

Linear Derating Factor (PCB Mount)

0.020

Single Pulse Avalanche Energy

140 mJ

Repetitive Avalanche Current

- 3.1 A

Repetitive Avalanche Energy

2.5 mJ

Maximum Power Dissipation T

= 25 °C

Maximum Power Dissipation (PCB Mount)

= 25 °C 2.5

Peak Diode Recovery dV/dt

dV/dt - 5.5 V/ns

Operating Junction and Storage Temperature Range T

, T

stg

- 55 to + 150

°C

Soldering Recommendations (Peak Temperature)

for 10 s 260

Summary of content (11 pages)

PAGE 1
IRFR9110, IRFU9110, SiHFR9110, SiHFU9110 www.vishay.com Vishay Siliconix Power MOSFET FEATURES PRODUCT SUMMARY VDS (V) • • • • • • • • - 100 RDS(on) () VGS = - 10 V 1.2 Qg (Max.) (nC) 8.7 Qgs (nC) 2.2 Qgd (nC) 4.
PAGE 2
IRFR9110, IRFU9110, SiHFR9110, SiHFU9110 www.vishay.com Vishay Siliconix THERMAL RESISTANCE RATINGS PARAMETER SYMBOL MIN. TYP. MAX. Maximum Junction-to-Ambient RthJA - - 110 Maximum Junction-to-Ambient (PCB Mount)a RthJA - - 50 Maximum Junction-to-Case (Drain) RthJC - - 5.0 UNIT °C/W Note a. When mounted on 1" square PCB (FR-4 or G-10 material). SPECIFICATIONS (TJ = 25 °C, unless otherwise noted) PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX.
PAGE 3
IRFR9110, IRFU9110, SiHFR9110, SiHFU9110 www.vishay.com Vishay Siliconix TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted) Fig. 1 - Typical Output Characteristics, TC = 25 °C Fig. 2 - Typical Output Characteristics, TC = 150 °C S13-0168-Rev. D, 04-Feb-13 Fig. 3 - Typical Transfer Characteristics Fig. 4 - Normalized On-Resistance vs. Temperature Document Number: 91279 3 For technical questions, contact: hvm@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
PAGE 4
IRFR9110, IRFU9110, SiHFR9110, SiHFU9110 www.vishay.com Fig. 5 - Typical Capacitance vs. Drain-to-Source Voltage Fig. 6 - Typical Gate Charge vs. Gate-to-Source Voltage S13-0168-Rev. D, 04-Feb-13 Vishay Siliconix Fig. 7 - Typical Source-Drain Diode Forward Voltage Fig. 8 - Maximum Safe Operating Area Document Number: 91279 4 For technical questions, contact: hvm@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
PAGE 5
IRFR9110, IRFU9110, SiHFR9110, SiHFU9110 www.vishay.com Vishay Siliconix RD VDS VGS D.U.T. RG +VDD - 10 V Pulse width ≤ 1 µs Duty factor ≤ 0.1 % Fig. 10a - Switching Time Test Circuit td(on) tr td(off) tf VGS 10 % 90 % VDS Fig. 9 - Maximum Drain Current vs. Case Temperature Fig. 10b - Switching Time Waveforms Fig. 11 - Maximum Effective Transient Thermal Impedance, Junction-to-Case S13-0168-Rev. D, 04-Feb-13 Document Number: 91279 5 For technical questions, contact: hvm@vishay.
PAGE 6
IRFR9110, IRFU9110, SiHFR9110, SiHFU9110 www.vishay.com Vishay Siliconix L Vary tp to obtain required IAS IAS VDS D.U.T RG VDS + V DD VDD IAS tp - 10 V 0.01 Ω tp Fig. 12a - Unclamped Inductive Test Circuit VDS Fig. 12b - Unclamped Inductive Waveforms Fig. 12c - Maximum Avalanche Energy vs. Drain Current Current regulator Same type as D.U.T. 50 kΩ QG - 10 V 12 V 0.2 µF 0.3 µF QGS - QGD D.U.T. VG + VDS VGS - 3 mA Charge IG ID Current sampling resistors Fig.
PAGE 7
IRFR9110, IRFU9110, SiHFR9110, SiHFU9110 www.vishay.com Vishay Siliconix Peak Diode Recovery dV/dt Test Circuit D.U.T. + Circuit layout considerations • Low stray inductance • Ground plane • Low leakage inductance current transformer + - - Rg + • dV/dt controlled by Rg • ISD controlled by duty factor “D” • D.U.T. - device under test + - VDD Note • Compliment N-Channel of D.U.T. for driver Driver gate drive P.W. Period D= P.W. Period VGS = - 10 Va D.U.T.
PAGE 8
Package Information www.vishay.com Vishay Siliconix TO-252AA Case Outline E MILLIMETERS A C2 e b2 D1 e1 E1 L gage plane height (0.5 mm) L4 b L5 H D L3 b3 C A1 INCHES DIM. MIN. MAX. MIN. MAX. A 2.18 2.38 0.086 0.094 A1 - 0.127 - 0.005 b 0.64 0.88 0.025 0.035 b2 0.76 1.14 0.030 0.045 b3 4.95 5.46 0.195 0.215 0.024 C 0.46 0.61 0.018 C2 0.46 0.89 0.018 0.035 D 5.97 6.22 0.235 0.245 D1 4.10 - 0.161 - E 6.35 6.73 0.250 0.265 E1 4.32 - 0.
PAGE 9
Package Information Vishay Siliconix TO-251AA (HIGH VOLTAGE) 4 3 E1 E Thermal PAD 4 b4 θ2 4 A 0.010 0.25 M C A B L2 4 c2 A θ1 B D D1 A C 3 Seating plane 5 C L1 L3 (Datum A) C L B B A A1 3 x b2 View A - A 2xe c 3xb 0.010 0.25 M C A B Plating 5 b1, b3 Base metal Lead tip c1 (c) 5 (b, b2) Section B - B and C - C MILLIMETERS DIM. MIN. MAX. INCHES MIN. MILLIMETERS MAX. DIM. MIN. INCHES MAX. MIN. MAX. A 2.18 2.39 0.086 0.094 D1 5.21 - 0.205 - A1 0.89 1.
PAGE 10
Application Note 826 Vishay Siliconix RECOMMENDED MINIMUM PADS FOR DPAK (TO-252) 0.224 0.243 0.087 (2.202) 0.090 (2.286) (10.668) 0.420 (6.180) (5.690) 0.180 0.055 (4.572) (1.397) Recommended Minimum Pads Dimensions in Inches/(mm) Return to Index Return to Index APPLICATION NOTE Document Number: 72594 Revision: 21-Jan-08 www.vishay.
PAGE 11
Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product.