User Manual
Table Of Contents
- ITALIANO
- INDICE
- 1. NOTE IMPORTANTI
- 1.1 CURA DEL PRODOTTO
- 1.2 NOTE RIGUARDANTI IL MANUALE
- 2. INTRODUZIONE
- 2.1 CARATTERISTICHE GENERALI DI LEGEND E LEGEND LIVE
- 3. COMANDI E CONNESSIONI
- 3.1 PANNELLO SUPERIORE
- 3.2 PANNELLI LATERALI
- 3.3 PANNELLO POSTERIORE
- 4. ACCENSIONE E NORMALE FUNZIONAMENTO
- 4.1 COSA SONO E COME SI UTILIZZANO I DRAWBARS
- 4.2 COSA SONO E COME SI UTILIZZANO I PRESETS
- 4.3 LA PERCUSSIONE
- 4.4 AGGIUNGERE I RUMORI INTERNI
- 5. AGGIUNGERE GLI EFFETTI AL SUONO
- 5.1 VIBRATO O CHORUS
- 5.2 REVERB
- 5.3 DRIVE
- 5.4 ROTARY
- 6. FUNZIONI AGGIUNTIVE
- 6.1 TRASPOSIZIONE
- 6.2 GOSPEL SET
- 6.3 FUNZIONE PANIC
- 6.4 FUNZIONE MIDI DUMP
- 7. APPENDICE
- 7.1 PRESET DI FABBRICA
- 7.2 MAPPA DELLE FUNZIONI RICHIAMABILI CON IL MANUALE SUPERIORE
- 7.3 RISOLUZIONE AI PROBLEMI PIU’ COMUNI
- ENGLISH
- INDEX
- 1. IMPORTANT NOTES
- 1.1 PRODUCT CARE
- 1.2 NOTES ABOUT THIS MANUAL
- 2. INTRODUCTION
- 2.1 GENERAL FEATURES OF LEGEND AND LEGEND LIVE
- 3. CONTROLS AND CONNECTIONS
- 3.1 UPPER PANEL
- 3.2 SIDE PANELS
- 3.3 REAR PANEL
- 4. SWITCHING ON AND NORMAL FUNCTIONING
- 4.1 WHAT ARE DRAWBARS AND HOW TO USE THEM
- 4.2 WHAT ARE PRESETS AND HOW TO USE THEM
- 4.3 PERCUSSION
- 4.4 INTERNAL NOISES SIMULATION
- 5. USING EFFECTS
- 5.1 VIBRATO OR CHORUS
- 5.2 REVERB
- 5.3 DRIVE
- 5.4 ROTARY
- 6. ADDITIONAL FUNCTIONS
- 6.1 TRANSPOSITION
- 6.2 GOSPEL SET
- 6.3 PANIC FUNCTION
- 6.4 MIDI DUMP FUNCTION
- 7. APPENDIX
- 7.1 FACTORY PRESETS
- 7.2 MAP OF THE FUNCTIONS RECALLED THROUGH THE UPPER MANUAL
- 7.3 TROUBLESHOOTING
- DEUTSCH
- INHALT
- 1. WICHTIGE HINWEISE
- 1.1 PFLEGE DES INSTRUMENTS
- 1.2 HINWEISE ZU DIESEM HANDBUCH
- 2. EINLEITUNG
- 2.1 AUSSTATTUNGSMERKMALE DER LEGEND UND LEGEND LIVE
- 3. REGLER UND ANSCHLÜSSE
- 3.1 OBERES BEDIENFELD
- 3.2 SEITLICHE BEDIENFELDER
- 3.3 RÜCKSEITE
- 4. EINSCHALTEN UND NORMALBETRIEB
- 4.1 ÜBER ZUGRIEGEL UND IHRE ANWENDUNG
- 4.2 ÜBER PRESETS UND IHRE ANWENDUNG
- 4.3 PERCUSSION
- 4.4 INTERNE GERÄUSCHSIMULATION
- 5. EFFEKTE ANWENDEN
- 5.1 VIBRATO ODER CHORUS
- 5.2 REVERB
- 5.3 DRIVE
- 5.4 ROTARY
- 6. WEITERE FUNKTIONEN
- 6.1 TRANSPOSITION
- 6.2 GOSPEL-SET
- 6.3 PANIK-FUNKTION
- 6.4 MIDI DUMP-FUNKTION
- 7. ANHANG
- 7.1 WERKS-PRESETS
- 7.2 KARTE DER MIT DEM OBEREN MANUAL ABRUFBAREN FUNKTIONEN
- 7.3 FEHLERSUCHE
MIDI - 2
Manuale Utente
viscount
MAIN MIDI MESSAGES TRANSMITTED AND RECEIVED BY THE LEGEND / LEGEND
LIVE
•
Note On:
9nH kkH vvH
This message is transmitted when a note is played, i.e. when a keyboard key is pressed. Each Note On
message includes the following codes:
Note On
(9nH): when a key has been pressed, n is the MIDI channel;
Note Number
(kkH): the key and thus the relative note which has been played;
Velocity
(vvH): velocity of the note (the force with which the key had been pressed).
Note messages are expressed as a number from 0 to 127, with Middle C represented by the number 60.
Upper and Lower Manuals
transmit Note On message as number from 36 to 96 (30 – 101 with transpose).
Pedalboard transmits notes as number from 36 to 60 (30 – 65 with transpose)
Since its velocity value is fixed, when drawbars Set A or B or a Preset is selected, the instrument always
sets the velocity value as 64. When Cancel mode is selected, the instrument transmits notes with variable
velocity.
•
Note Off:
8nH kkH vvH
This message is transmitted when the key pressed previously is released. When it is received, the sound of
the note of that key is deactivated. Each Note Off message includes the following codes:
Note Off
(8nH): a key has been released, n is the MIDI channel;
Note Number
(kkH): which key has been released;
Velocity
(vvH): velocity (amount of force) with which it has been released.
N.B.:
A Note On message with Velocity=0 is considered as a Note Off message.
•
Control Change:
BnH ccH vvH
These are control messages (often associated to sliders or pedals) used to add expression to the
performance, by allowing definition (and real-time control) of the timbre parameters, such as the volume
(CC n.7) or the amount of reverb (CC n.91), etc. Each Control Change message includes the following
codes:
Control Change
(BnH): a control has been regulated, n is the MIDI channel;
Control Change Number
(kkH): which control has been regulated;
Value
(vvH): value set by the control.
•
Pitch Bend:
EnH H vvH ssH
Controls the instrument general tuning. This message includes the following codes:
Pitch Bend
(EnH): the pitch has been adjusted. n is the MIDI channel;
1st byte tuning
(vvH)
2nd byte tuning
(ssH)
N.B.:
this message is only received.