User's Manual

ManualsBrandsVirtue ManualsPaintballVirtue pm6

This manual provides installation and operating

instructions for the Virtue DM6 Board

Features:

• 7 Modes of fire - Semi Auto, PSP Mode,

NXL Mode, Ramp Mode, Auto Response,

Full Auto, and Breakout Mode.

• 15BPS Ready - Be ready for any tournament

series! Put Dipswitch 1 in the off position,

and your maximum rate of fire is capped at

15bps!

• All firing modes have user adjustable

maximum rates of fire from 10.50bps to

unlimited rates of fire!

• Virtue Trigger Logic constantly monitors the

trigger to ensure every trigger pull is

recognized, giving you the fastest responding

gun, and highest possible rates of fire.

• Adjustable Debounce, Dwell, Anti-

Mechanical Bounce (AMB), Eye Sensitivity,

Ramp Activation Speed, Ramp Percentage,

Anti-Bolt Stick (ABS).

• Power Efficient Software extends the life of

your battery.

• All settings are stored in non-volatile memory

so they will not be lost when the battery dies

or is removed.

• 10 minute idle auto-shutdown saves battery

life.

• Low battery indicator software.

• Forced Shot allows the marker to be fired

when the eyes are enabled, but no object is in

the breech.

• Instant On allows the marker to be fired

instantly upon turn on.

• Tournament Lock/Unlock allows the marker

to be programmed through the trigger without

having to constantly open the grip. With the

tournament lock enabled, settings cannot be

changed without opening up the grip.

Installing Your Virtue DM6 Board:

1. Open up the grip from the right side of the marker

to expose the circuit board.

2. Remove the two screws holding the stock circuit

board into place, and carefully disconnect the two

wire harnesses and the battery.

3. Remove the Stock Board from the Grip Frame,

taking care to leave the two metal push buttons in

place.

4. Connect the wires you removed in step 2 to the

Virtue DM6 Board, and then screw the Virtue DM6

Board into place.

5. Reconnect the battery, close the grips, and you’re

done!

Setting the Dipswitches:

On the DM6 circuit board, above the two push buttons, there is

a 2 position dipswitch.

Dipswitch 1 is the Max Rate of Fire/15bps Cap lock. If

Dipswitch 1 is in the on position, your max rate of fire is set to

your “Max Rate of Fire” setting (Flickering Red LED in

programming mode.) If dipswitch 1 is in the off position, the

Max Rate of Fire of all modes is capped at 15bps. After

changing this setting, you must turn the marker off before it

takes effect.

*Please note the actual bps will vary slightly from gun to gun.

If the desired bps is too high or too low with dipswitch 1 down,

then leave Dipswitch 1 in the up position, and adjust the max

rate of fire setting through the programming menu.

Dipswitch 2 is the Tournament Lock. To access the

programming mode of the Virtue DM6 Board, Dipswitch 2

must be in the on position. Then hold down the trigger and

turn the marker on to enter programming mode. When

Dipswitch 2 is in the off position, the gun is in “Tournament

Lock”, and program settings cannot be changed.

LED Indicator:

Solid Yellow (During startup) Indicates a low battery

Solid Blue Ball in Breach; Gun is ready to fire

Solid Red No Ball in Breach

Flashing Red Eyes disabled

Flashing Blue Eye malfunction

Power Operation:

The Virtue DM6 Board uses Instant On technology. Simply

tap the power button, and the marker instantly turns on and is

ready to fire. To turn the marker off at any time, press the

power button for 1 second.

Eye Operation:

When the marker is turned on the eye system is automatically

enabled. The eyes can be toggled on and off by pressing the

eye button (bottom button) for 1 second. When the eyes are

disabled the max rate of fire will not go over 24bps.

The eye logic also differentiates between a ball being fired, and

something continually blocking the eye (like broken paint, or

your finger). If the eye becomes blocked, the LED will flash

blue, indicating an eye malfunction. When the object blocking

the eyes is removed the eye will automatically return to

working mode (solid red or blue LED).

Low Battery Indicator:

If your battery is low, the LED will be yellow for 1 second

when you turn the marker on

Programming Mode:

To access the programming mode of the Virtue DM6

Board, Dipswitch 2 must be in the on position. When

Dipswitch 2 is in the off position, the gun is in

“Tournament Lock”, and program settings cannot be

changed.

With Dipswitch 2 in the on position, hold the trigger

and turn the marker on. The LED will then cycle

through a rainbow of colors and stop on purple,

indicating that you are now in programming mode.

Tapping the trigger will then toggle through the

different programming modes:

Purple: Firing Mode

Green: Debounce

Blue: Ramp Activation Speed

White: Ramp Percentage

Red: Dwell

Teal: Eye Sensitivity

Yellow: AMB

(Anti-Mechanical Bounce)

Flickering Green ABS (Anti-Bolt Stick)

Flickering Red: Max Rate of Fire

To Change the Value of a Setting:

When the LED is lit for the desired setting, pull and

hold the trigger until the LED Begins to flash. The LED

will flash the number of times the current value is set to.

When the LED stops flashing you then have 2 seconds

to enter in the new value by tapping the trigger the

amount of times you want the new value to be set to.

After you have set the new value, the LED will flash

back at you the number of times you have just entered,

and then flash through the rainbow of colors, returning

to the color you have just adjusted, indicating that the

new value has been set. To exit programming mode,

shut the marker off.

Programming Example:

If you want to change the debounce to 2 you would:

1. With the marker off, and Dipswitch 2 in the

on position, hold the trigger and turn the

marker on.

2. The LED will now cycle through a rainbow of

colors and stop on purple.

3. Tap the trigger once so the LED glows green.

4. Pull and hold the trigger until the LED starts

to flash (factory default for debounce is 5, so

the LED will flash 5 times).

5. When the LED stops flashing, quickly tap the

trigger 2 times.

6. The LED will now flash 2 times, and then

flash through the rainbow of colors, and stop

on green, indicating the new value has been

set.

7. To exit programming mode, shut the marker

off.

Reset to Factory Default:

To return all settings to the factory defaults, while in

programming mode, hold the trigger down for 10 seconds until

the LED turns white. Once the LED turns white, the LED will

then flash through the rainbow of colors indicating that all

settings have been returned to the factory default.

Summary of content (2 pages)

PAGE 1
This manual provides installation and operating instructions for the Virtue DM6 Board. Features: • • • • • • • • • • • • 7 Modes of fire - Semi Auto, PSP Mode, NXL Mode, Ramp Mode, Auto Response, Full Auto, and Breakout Mode. 15BPS Ready - Be ready for any tournament series! Put Dipswitch 1 in the off position, and your maximum rate of fire is capped at 15bps! All firing modes have user adjustable maximum rates of fire from 10.
PAGE 2
Adjustable Settings: Firing Mode (Purple) Values 1-7 (Default is 1) 1 2 3 4 5 6 7 Semi Auto- Semi Automatic Fire; 1 trigger pull equals 1 shot. PSP Ramp Mode- The first 3 shots of a string are Semi Auto. After the 4th shot the marker will ramp to the rate of fire your “Max Rate of Fire” is set to. Once the trigger is let go and 1 second elapses, the 3 shot Semi Auto count restarts. NXL Style Full Auto- The first 3 shots of a string are Semi Auto.