Manual

This manual provides installation and operating
instructions for the Virtue Cyborg Board
.
Features:
• 7 Modes of fire - Semi Auto, Modified
PSP/NXL, NXL Style Full Auto, Ramp
Mode, Auto Response, Full Auto, and
Breakout Mode.
• 15BPS Ready - Be ready for any tournament
series! Put Dipswitch 1 down, and your
maximum rate of fire is capped at 15bps!
• All firing modes have user adjustable
maximum rates of fire from 10.50bps to
unlimited rates of fire!
• Virtue Trigger Logic constantly monitors the
trigger to ensure every trigger pull is
recognized, giving you the fastest responding
gun, and highest possible rates of fire.
• Adjustable Debounce, Dwell, Anti-
Mechanical Bounce (AMB), Eye Sensitivity,
Ramp Activation Speed, Ramp Percentage,
Anti-Bolt Stick (ABS).
• Power Efficient Software extends the life of
your battery.
• All settings are stored in non-volatile memory
so they will not be lost when the battery dies
or is removed.
• 10 minute idle auto-shutdown saves battery
life.
• Forced Shot allows the marker to be fired
when the eyes are enabled, but no object is in
the breech.
• Instant On allows the marker to be fired
instantly upon turn on.
• Tournament Lock/Unlock allows the marker
to be programmed through the trigger without
having to constantly open the grip. With the
tournament lock enabled, settings cannot be
changed without opening up the grip.
Installing the Virtue Cyborg Board:
1. Remove the grip screws and grip from your Cyborg
Marker.
2. Disconnect both eye harnesses from the stock
board, and remove the eye cover and screws from
the grip frame.
3. Separate the Cyborg body from the frame taking
care not to damage the solenoid wires.
4. Disconnect the solenoid wires from the solenoid
and then remove the stock board from your Cyborg.
5. Install the Virtue Cyborg board by screwing it into
place, and connecting all wires.
6. Put the Cyborg body and frame back together taking
care not to pinch any wires.
7. Screw the eye cover back into place as well as the
grips.
8. Destroy the Competition!
Please note that the trigger settings maybe need to be adjusted
during or after installation.
Setting the Dipswitches:
On the Virtue Cyborg Board, there is a 2 position dipswitch.
To access the programming mode of the Virtue Cyborg
Board, Dipswitch 2 must be in the on position. When
Dipswitch 2 is in the off position, the gun is in
“Tournament Lock”, and program settings cannot be
changed.
Dipswitch 1 is the Max Rate of Fire/15bps Cap lock. If
Dipswitch 1 is in the on position, your max rate of fire is set to
your “Max Rate of Fire” setting (Flashing Red LED in
programming mode.) If dipswitch 1 is in the off position, the
Max Rate of Fire of all modes is capped at 15bps. After
changing this setting, you must turn the marker off before it
takes effect.
*Please note the actual bps will vary slightly from gun to gun.
If the desired bps is too high or too low with dipswitch 1 off,
then leave Dipswitch 1 in the on position, and adjust the max
rate of fire setting through the programming menu.
Dipswitch 2 is the Tournament Lock. To access the
programming mode of the Virtue Cyborg Board, Dipswitch 2
must be in the on position. Then hold down the trigger and
turn the marker on to enter programming mode. When
Dipswitch 2 is in the off position, the gun is in “Tournament
Lock”, and program settings cannot be changed.
LED Indicator:
Solid Green Ball in Breach; Gun is ready to fire
Solid Red No Ball in Breach
Flashing Red Eyes disabled
Flashing Green Eye malfunction
Power Operation:
The Virtue Cyborg Board uses Instant On technology. Simply
tap the power button, and the marker instantly turns on and is
ready to fire. To turn the marker off at any time, press the
power button for 2 seconds.
Eye Operation:
When the marker is turned on the eye system is automatically
enabled. The eyes can be toggled on and off by pressing the
power button for 1 second. When the eyes are disabled the
max rate of fire will not go over 24bps.
The eye logic differentiates between a ball being fired, and
something continually blocking the eye (like your finger). If
the eye becomes blocked, the LED will flash green, indicating
an eye malfunction. When the object blocking the eyes is
removed the eye will automatically return to working mode
(solid red or green LED).
Programming Mode:
With Dipswitch 2 in the on position, hold the trigger
and turn the marker on. The LED will then cycle
through a rainbow of colors and stop on yellow,
indicating that you are now in programming mode.
Tapping the trigger will then toggle through the
different programming modes:
Yellow: Firing Mode
Green: Debounce
Red: Ramp Activation Speed
Flickering Yellow: Ramp Percentage
Flickering Green: Dwell
Flickering Red: Eye Sensitivity
Flashing Yellow: AMB (Anti-Mechanical Bounce)
Flashing Green ABS (Anti-Bolt Stick)
Flashing Red: Max Rate of Fire
To Change the Value of a Setting:
When the LED is lit for the desired setting, pull and
hold the trigger until the LED Begins to flash. The LED
will flash the number of times the current value is set to.
When the LED stops flashing you then have 2 seconds
to enter in the new value by tapping the trigger the
amount of times you want the new value to be set to.
After you have set the new value, the LED will flash
back at you the number of times you have just entered,
and then flash through the rainbow of colors, returning
to the color you have just adjusted, indicating that the
new value has been set. To exit programming mode,
shut the marker off.
Programming Example:
If you want to change the debounce to 2 you would:
1. With the marker off, and Dipswitch 2 in the
on position, hold the trigger and turn the
marker on.
2. The LED will now cycle through a rainbow of
colors and stop on yellow.
3. Tap the trigger once so the LED glows green.
4. Pull and hold the trigger until the LED starts
to flash (factory default for debounce is 5, so
the LED will flash 5 times).
5. When the LED stops flashing, quickly tap the
trigger 2 times.
6. The LED will now flash 2 times, and then
flash through the rainbow of colors, and stop
on green, indicating the new value has been
set.
7. To exit programming mode, shut the marker
off.
Reset to Factory Default:
To return all settings to the factory defaults, while in
programming mode, hold the trigger down for 10 seconds until
the LED turns yellow. Once the LED turns yellow, the LED
will then flash through the rainbow of colors indicating that all
settings have been returned to the factory default.