Instructions / Assembly

ManualsBrandsViqua ManualsKitchenReplacement UV lamp compatible with D D4/PLUS D4-V C C4 C4-V and IHS (D4) UV-10 IHS-10 UV systems

VIQUA Lamp and Quartz Sleeve Replacement

Models: D4, E4, F4, D4 Premium, Plus Models

Discontinued Models: A, B, C, D, E, F, B4, C4

Overview

UV Lamp replacement: The amount of UV light created by the UV lamp decreases over time, requiring that the UV lamp be

replaced. The system will automatically notify you when it is time to replace the UV lamp.

Lamp Sleeve replacement/maintenance: Minerals in the water slowly form a coating on the quartz sleeve. This coating must be

removed because it reduces the amount of UV light reaching the water, thereby reducing disinfection performance. If the lamp

sleeve can not be cleaned, it must be replaced.

Section 1 Safety Information

Please read this entire instruction sheet before installation. Pay attention to all danger, warning, and caution statements.

Failure to do so could result in serious personal injury or damage to the equipment.

Make sure that the protection provided by this equipment is not impaired. Do not use or install this equipment in any manner

other than that specified in the instruction sheet.

1.1 Safety Precautions

DANGER

Failure to follow these instructions will result in serious injury or death.

Shock Hazard - Stored Energy

• Disconnect power to system before performing any maintenance or repair.

• There may be more than one source of power. Only connect to a GFCI.

• Protective ground

• DO NOT touch with wet hands.

Pressurized Device - Impalement Hazard

• NEVER perform any physical inspection, repair or maintenance on UV chamber unless UV chamber has been isolated and depressurized.

• NEVER service UV lamps, lamp sleeves or associated hardware until depressurization of UV chamber has been confirmed.

• DO NOT store any combustible or flammable material close to the system.

Instruction Sheet

602808_RevY

Summary of content (6 pages)

PAGE 1
Instruction Sheet VIQUA Lamp and Quartz Sleeve Replacement Models: D4, E4, F4, D4 Premium, Plus Models Discontinued Models: A, B, C, D, E, F, B4, C4 Overview UV Lamp replacement: The amount of UV light created by the UV lamp decreases over time, requiring that the UV lamp be replaced. The system will automatically notify you when it is time to replace the UV lamp. Lamp Sleeve replacement/maintenance: Minerals in the water slowly form a coating on the quartz sleeve.
PAGE 2
Maintenance WA R N I N G Failure to follow these instructions could result in serious injury or death. UV Light Hazard UV • ALWAYS use UV protective gear, including gloves and UV safety glasses. • NEVER look directly at illuminated UV lamp, even when using protective gear. • NEVER illuminate UV lamp outside of the UV chamber. • If accidental exposure occurs, immediately cool affected area and consult physician.
PAGE 3
Maintenance 2.1 Replacing UV Lamp and Lamp Sleeve NOTICE Do not use water during replacement of UV lamp. Lamp replacement is a quick and simple procedure requiring no special tools. The UV lamp must be replaced after 9000 hours of continuous operation (approximately one year) in order to ensure adequate disinfection. Procedure: 1 3 2 4 1 1 1 2 2 1 10 mins 0 Old 15 45 New 30 • Close all faucets and water supply. • Press the pressure button to release the pressure from the cartridges.
PAGE 4
Maintenance 9 10 1 12 11 2 Mild Acid • Unscrew the sleeve bolt and carefully remove it from the top of the chamber. Note: Sleeve may be attached to sleeve bolt. Hold sleeve with other hand while removing sleeve bolt. 13 • Clean the quartz sleeve with a cloth soaked in CLR, vinegar or some other mild acid and then rinse with water. • Ensure quartz sleeve is properly centered in the chamber. Note: If sleeve cannot be cleaned completely or it is scratched or cracked, then replace the sleeve.
PAGE 5
Maintenance 17 18 19 20 Ring clamp • Align connections by rotating ring clamp to push lamp plug onto end of lamp. • Install the safety cap. • Connect the green ground wire and red strain relief wire to the chamber using the grounding screw. • Align connection pins with the lamp connector by rotating the ring clamp. • Push the lamp connector down onto the lamp pins and the ring clamp pins until an audible click is heard. Note: Ensure the connector is engaged on both sides.
PAGE 6
425 Clair Rd. W, Guelph, Ontario, Canada N1L 1R1 t. (+1) 519.763.1032 • tf. (+1) 800.265.7246 (US and Canada only) t. (+31) 73 747 0144 (Europe only) • f. (+1) 519.763.5069 e-mail: info@viqua.com www.viqua.