Install guide

ManualsBrandsViper ManualsAutomotive9153VL

Index

Rev.: 20130222

Platform: DBALL

Firmware: TL2 Remote Start Ready Installation (RSR)

† Toyota and Lexus are registered trademarks and property of their respective companies.

Vehicle Application Guide

Installation Types

Module Programming...................

..................................................................................................................................................

OEM Remote Starter Detection.........................................................................................................................................

Type 1a (with T-Harness)..................................................................................................................................................

Type 1b (without T-Harness)............................................................................................................................................

Vehicle Wiring Reference Chart - Type 1...........................................................................................................................

Type 2a (with T-Harness)..................................................................................................................................................

Type 2b (without T-Harness)............................................................................................................................................

Vehicle Wiring Reference Chart - Type 2..........................................................................................................................

(without T-Harness)............................................................................................................................................

Vehicle Wiring Reference Chart - Type 3..........................................................................................................................

Features Programming......................................................................................................................................................

Type 3a (with T-Harness).................................................................................................................................................. 10

Type 3b 11

Programming

..................................................................................................................................... 13

Module Reset..................................................................................................................................................................... 14

Hard Reset......................................................................................................................................................................... 14

Features & Options List..................................................................................................................................................... 15

LED Diagnostics & Troubleshooting.................................................................................................................................. 16

Parking Light Error Codes................................................................................................................................................. 16

Optional RF Kits................................................................................................................................................................. 17

Limited One-Year Consumer Warranty.............................................................................................................................. 19

Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle

on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to

start the vehicle from a distance.

completely

Installation Guide

Update Alert: Firmware updates are posted on the web on a regular basis. We recommend

that you check for firmware and/or install guide updates prior to installing this product.

Important!

This product is NOT compatible with vehicles equipped with a manual transmission.

This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a

Plug & Play (TLTH2) T-Harness (Optional). This solution offers three (3) configuration options to control

your system; 3x OEM Lock Remote Start Activation*, RF Kit or SmartStart (all sold separately). Refer to

pages 17-18 for a list of RF kits and their part numbers.

* 3x OEM Lock Remote Start Activation is a feature that allows users to control an XpressStart or a

DBALL in RSR using the factory (OEM) remote control.

Note: Only available on certain models, check the Vehicle Application Guide for compatibility with

specific year and model.

Refer to Quick Reference Guide (QRG) at the end of this guide for more information on how to use

various features offered with this product.

SmartStart Compatible

SmartStart is equipped with D2D, which means it can be connected to an interface module and used in Remote

Start Ready (RSR) mode without the use of a remote starter. See the Module Programming section for more

information.

Summary of content (22 pages)

PAGE 1
Platform: DBALL Firmware: TL2 Remote Start Ready Installation (RSR) Rev.: 20130222 Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a Plug & Play (TLTH2) T-Harness (Optional).
PAGE 2
Platform: DBALL Firmware: TL2 Remote Start Ready Installation (RSR) Rev.
PAGE 3
Platform: DBALL Firmware: TL2 Remote Start Ready Installation (RSR) Rev.: 20130222 Page 3 How to Know if the Vehicle is Equipped with an OEM Remote Starter 1- An “ENGINE STARTER” sticker should be on the remote. 2- Remote start the OEM remote starter: Press the remote control’s lock button twice within 2 seconds, then press and hold the lock button for 3 seconds. The parking lights flash after 3 seconds. The engine starts and the parking lights flash repeatedly for 20 seconds.
PAGE 4
Platform: DBALL Firmware: TL2 Remote Start Ready Installation (RSR) Rev.: 20130222 Page 4 Installation Type 1a (with T-Harness) Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL. The optional XL202 and antenna are not included and MUST be purchased separately.
PAGE 5
Platform: DBALL Firmware: TL2 Remote Start Ready Installation (RSR) Rev.: 20130222 Page 5 Installation Type 1b (without T-Harness) Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL. The optional XL202 and antenna are not included and MUST be purchased separately.
PAGE 6
Platform: DBALL Firmware: TL2 Remote Start Ready Installation (RSR) Rev.
PAGE 7
Platform: DBALL Firmware: TL2 Remote Start Ready Installation (RSR) Rev.: 20130222 Page 7 Installation Type 2a (with T-Harness) Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL. The optional XL202 and antenna are not included and MUST be purchased separately.
PAGE 8
Platform: DBALL Firmware: TL2 Remote Start Ready Installation (RSR) Rev.: 20130222 Page 8 Installation Type 2b (without T-Harness) Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL. The optional XL202 and antenna are not included and MUST be purchased separately.
PAGE 9
Platform: DBALL Firmware: TL2 Remote Start Ready Installation (RSR) Rev.
PAGE 10
Platform: DBALL Firmware: TL2 Remote Start Ready Installation (RSR) Rev.: 20130222 Page 10 Installation Type 3a (with T-Harness) Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL. The optional XL202 and antenna are not included and MUST be purchased separately.
PAGE 11
Platform: DBALL Firmware: TL2 Remote Start Ready Installation (RSR) Rev.: 20130222 Page 11 Installation Type 3b (without T-Harness) Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL. The optional XL202 and antenna are not included and MUST be purchased separately.
PAGE 12
Platform: DBALL Firmware: TL2 Remote Start Ready Installation (RSR) Rev.
PAGE 13
Platform: DBALL Firmware: TL2 Remote Start Ready Installation (RSR) Rev.: 20130222 Page 13 Module Programming Refer to the LED Diagnostics section on page 16 for more information and for troubleshooting purposes. Important Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step.
PAGE 14
Platform: DBALL Firmware: TL2 Remote Start Ready Installation (RSR) Rev.: 20130222 Page 14 Module Reset A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected. 1 2 If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
PAGE 15
Platform: DBALL Firmware: TL2 Remote Start Ready Installation (RSR) Rev.: 20130222 Page 15 Feature and Option List It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on www.xpresskit.com. The web offers more options such as EIPS and RSR; however, manual configuration of the features is possible using the information on this page. Feat.
PAGE 16
Platform: DBALL Firmware: TL2 Remote Start Ready Installation (RSR) Rev.: 20130222 Page 16 LED Diagnostics and Troubleshooting LED Status Description Troubleshooting Programming the Module Solid Solid Red Waiting for the completion of a programming sequence, or for the ignition to be turned ON. This can also mean that there is an issue with the data bus wiring. Make sure that the connections to the data bus are correct by referring to the wiring diagram.
PAGE 17
Platform: DBALL Firmware: TL2 Remote Start Ready Installation (RSR) Rev.: 20130222 Page 17 Optional RF Kits Note: RF kits are sold SEPARATELY. Request an order from Directed using the part numbers listed below. 9211VL Viper 1-Way Responder ONE - Plug & Play RF Kit with XL202. UPC: 093207 08488 1 Also available as: § Python: 9211PL § Clifford: 9211XL 9153VL Viper 1-Way - Plug & Play RF kit with XL202.
PAGE 18
Platform: DBALL Firmware: TL2 Remote Start Ready Installation (RSR) Rev.: 20130222 Page 18 Optional RF Kits Note: RF kits are sold SEPARATELY. Request an order from Directed using the part numbers listed below. AF-RFK623 AF-RFK5225 Astrostart 2-way LED Receiver kit with up to 1,500’ of range. UPC: 093207 08752 3 Astrostart 2-way LCD Receiver kit offering XRTTM technology with up to 5,000’ of range. UPC: 093207 08753 0 AS-RFK1700 AS-RFK2300 Autostart 1-way Receiver kit with up to 3,000’ of range.
PAGE 19
Platform: DBALL Firmware: TL2 Remote Start Ready Installation (RSR) Rev.: 20130222 Page 19 Limited One Year Consumer Warranty For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics.
PAGE 20
Quick Reference Guide DBALL-TL2 RSR Rev.: 20130222 Pit Stop Mode The Pit Stop Mode feature is practical when you need to stop and run an errand, but wish to keep the engine running. 1 Stop the vehicle in a safe parking spot and put the gear in Park (P). & P Stop & put vehicle in Park (P) 2 3 Press the start button to activate the Pit Stop Mode. It is now safe to leave the engine running and exit the vehicle with the Smart Key in hand.
PAGE 21
Quick Reference Guide DBALL-TL2 RSR Rev.: 20130222 List of Available Commands SmartStart Compatible Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information. Button(s) Actions This system is compatible with Directed SmartStart 3.0. For a complete list of supported features, please visit www.mysmartstart.com.
PAGE 22
Quick Reference Guide DBALL-TL2 RSR Rev.: 20130222 Engine Idle Protection System (EIPS) Vehicles equipped with RFID-type Push-to-Start ignition systems work by detecting a proximity key in the vehicle. They will run indefinitely if the key is removed, which could potentially lead users to exiting the vehicle while the engine is still running and the car is left idling on its own in a garage or a confined space. To mitigate risk, we have designed a feature that is now available on the DBALL.