ORE;_o. No_oo. • ,NNo_., oN 24" 1080p LED Bocklight LCD Television with Built-in D VD Player LED24VF65D AIR (TV)/CABLE MODE SELECTION The Air/CABLE menu option is set to the "CABLE" (Cable Television) mode at the factory. If you want to use an antenna for the built-in TV tuner, this menu option must be set to the "Air" mode. Please refer to page 19 of the owner's manual for the details of this menu.
Contents Contents Caution Safety Information 2 3 Unit and Accessories Product Feature 4 4 Introduction 1. Front View 2. Rear View 3. Remote Control 5-8 5 6 7-8 Connection 9-11 Basic Operation 12-13 OSD Menu 1. Picture menu 2. Audio menu 3. Time menu 14-20 14 15 16 17 18 19-20 4. Setup menu 5. Lock menu 6.
Calitioll Caution The lightening flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of un-insulated "dangerous voltage" within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to the persons. The exclamation point within an equilateral triangle is intend to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Safety Information To ensure reliable and safe operation of this equipment, please read carefully instructions in this user guide, especially the safety information below. Electrical all the safety ° The TV set should only be connected to a mains supply which matches that stated on the label on the mains adaptor ° To prevent overload, don't share the same mains supply socket with too many other items of equipment. -Do not place any connecting wires where they may be stepped on or tripped over.
Unit and Accessories and Product Feature Unit and Accessories I I | | TV set User's Manual User's manual Remote control Batteries: 2xAAA Mains adaptor Mains cable Product Feature • 23.
Introduction Introduction 1. Front View + 4 CH- CH+ VOL- VOL+ iNPUT PLAY EJECT P i / _'A I | I I I I I 1 I I I I | I t I °-. _oo ++ ,* + , I Remote I , Control window © o LED Indicator Please insert a 12cm disc by following this instruction. 1. (IR) Infrared Receiver: Receives IR signals from the remote control. (Power on/Standby)LED Indicator: Press POWER to turn on and off.
Introduction 2. Rear View mll v 1 ] I @ @ I I I I | ,--1 1. m I @ @ | m t 9 -8 >- I POWER 1 Service I 2 HDMI2 HDMI1 i, i 3 VGA PC-IN Coax Headphone 4 5 6 7 I I 1. POWER: Connect to the mains adaptor. 2. Service : For software update only. 3. HDMII/2: Connect it to the HDMI of DVD or other equipment. 4. VGA: For PC display.Connect it to the D-Sub 15 pins analog output connector of the PC. 5. PC-IN: Connect it to the audio output terminal of PC. 6.
Introduction 3. Remote Control The remote control is using Infra-Red(IR). Point it towards the front of the LCD TV. The remote control may not work correctly if it is operated out of range or out of angle. INPUT POWER Press to display the input source menu Press to turn the TV on/standby PICTURE NUMBER Press repeatedly to cycle through the available video picture modes. BUTTONS To select the program e.g.: Select channel SOUND directly. 5, press "5" button.
Introduction Number buttons for DVD. Pressing "-/--"button to display "SELECT 10+", and press a number button to play the program. DISPLAY( In DVD) Press to display the current mode's information. LANGUAGE Select DVD disc language. ZOOM Adjust picture size in DVD mode. SUBTITLE Select DVD disc subtitle. SLOW Play DVD programs at slow speed. MENU DVD play list/Disc menu DVD eject. I,/11 Play/Pause ANGLE Select DVD picture angle. TITLE DVD title. GOTO Play your favorite title/chapter/track. DVD program.
Connection Connection Power Cord Connection _llll kJ 1 [ _3 i I_ER - Connect to the power supply correctly Service HDMI2 HDMI1 VGA PC-IN Coax Headphone J I as shown with the mains cable and mains adaptor• - When you connect the power, the TV set comes into standby mode and the LED indicator (Page 5) lights red.
Connection AV Input Connection Note: All cables shown are not included with the TV. Y Pb Pr Video L-in R-in RCA Video Cable YPbPr RF RCAAudio _=:::= _i D_ k Cable otoo"_ DVD or VCR A Connection Note: All cables shown are not included with the TV.
Connection HDMI Connection Note: All cables shown are not included with the TV. Service HDMI2 HDMI1 VGA PC-IN Coax Headphone I iiiiiiil_ HDMI cable DVDorVCR PC Connection Note: All cables shown are not included with the TV. HDMI1 VGA PC-IN Coax Headphone [ Caudio If using a sound card, adjust the PC sound as required. Set the video resolution of your PC to 1024x768, 60Hz on its VGA cable_ I cable original monitor.
Basic O_eration Basic Operation Power on/off 1. Connect to the power with a mains cable and an adaptor 2.-To turn on the TV Press POWER button on the TV or remote control. -To turn off the TV Press POWER button on the TV or remote control. (page9). Input Source select Press INPUT button on the TV set or remote control to display the input source menu, and use CH+/- button on the TV set or A / V button on remote control to select the input source, press OK button on the remote control to enter.
Basic O_eration Basic OSD Menu operation Press MENU button to display the OSD menu as below: | Use < / > button to select the main menu, and press V button to enter the submenu. In the submenu, use/k / V button to select the function item, and you could: adjust ("Contrast" item in Picture menu for example) with < / > button; select ("Picture Mode" item in Picture menu for example) with < / > button; enter the submenu ("Close Caption" item in Setup menu for example) with > button.
OSD Menu OSD Menu 1. Picture menu Picture mode: Select between Standard, Dynamic, Mild, Sports and User. You may select the picture mode directly by pressing the PICTURE button on the remote control. Contrast: Control the difference between the bright and dark regions of the screen picture. Brightness: Adjust brightness of the picture. Color: Adjust color of the picture. Tint: Control the fresh tones to make them appear natural. Sharpness: Set the amount of fine detail in the picture. Color Temp.
OSD Menu 2. Audio menu Sound Mode: Select your desired picture mode as follow: Flat, Music, Movie, Sports and User You may select the sound mode directly by pressing the SOUND button on the remote control. Bass: Low frequencies intensity. Treble: High frequencies intensity. Balance: Left and right stereo audio channels balance. Surround: Activate or deactivate the Surround function. SPDIF Type: Select spdif type between PCM and RAW. Audio Language: Select audio language.
OSD Menu 3. Time menu Sleep timer: You may set the automatic deactivate this function. shutdown timer choosing from 5 to 240 minutes, or Time zone: Select between Pacific, Alaska, Hawaii, Eastern, Central and Mountain. Daylight Saving Time: Select between On and Off. Clock: User can not change time manually during DTV mode, for time is from signal source directly.
OSD Menu 4. Setup menu Menu Language: Select Transparency: Turn on Zoom Mode: Select the 4:3, 4:3 zoom. Noise reduction: Select OSD menu language. or off the transparency menu function. zoom mode between 16:9, 16:9 zoom, the noise reduction mode between Strong, Off, Weak and Middle. PC SETUP: If the video input signal comes from your PC, you may adjust the V-Position, H-Position, Frequency, Phase or even perform an Auto adjustment.
OSD Menu 5. Lock menu You must enter the password You may modify the following to gain access to the Lock menu. The default password options: is 0000. Change password: Change the password, you must enter the new password twice to confirm it. Note: Do not forget the password. Lock: Allow you to turn on or off the system lock. If deactivated, the functions described below don't work. This option menu allows you to lock any TV channel or adjust the Movie rating filter.
OSD Menu 6. Channel menu Air/Cable: Allow you to select antenna between Air and Cable. If you selet "Cable", the following items(Favorite, Show/Hide, and DTV Signal) are unable to use. Auto Scan: Enter the Auto Scan menu to start auto scan. Channel NO, Channel "k If you select "Cable" as input signal in Antenna item, allows you to select Cable System among: Auto, STD, IRC and HRC. Use V button to highlight the "Start to Scan", then press > button to search the channels automatically.
OSD Menu Show/Hide: Allow you to show or hide the channels. Use A / V button to highlight the desired OK button to show or hide the highlighted Channel item, then press channel. > No.: Show and select the channel. Channel Label: Allow you to setup a label for the channel. Press < / > button to select the position of the table, and press A / V button to select the words. DTV Signal: Show the quality of digital signal: good, Normal, 20 Bad.
D VD Operations DVD basic operation Press the Power button on the TV or the remote control, then press the INPUT button to select DVD mode. Place a disc Insert a disc with the mirror side facing towards you. If the disc is double sided, place the title you want to play facing you. Do not touch the playing surface. Hold the disc around the outside with your fingers and place the disc into the slot. The player will automatically draw the disc into the player.
D VD Operations 4. According to the Direction Indicator on the menu, you can press Arrow buttons to highlight where you want to enter. 5. During Program Playback, if program button is repressed, the program order and the contents will be displayed on the screen, and the Program Playback will be stopped; also you can press Stop and Play to resume normal playback. 6. Notes: To clear the program order, use Arrow buttons to highlight the "CLEAR" item, then press Enter.
D VD Operations 2. While a disc is playing, press Repeat button once and the repeat banner appears to show current repeat mode. a) In CD, HD-CD, WMA or Digital Audio disc/JPEG sequence playback mode. Press Repeat button again to turn on repeat mode. Press the button again on the remote to turn to the next repeat mode. There are three repeat options: Off, Track Repeat and Disc Repeat. With each consecutive press of the button, the repeat mode switches.
D VD Operations Subtitles 1. Compatible with DVD discs. 2. Press the Subtitle button on the remote once, and the subtitle info banner appears 3. When a DVD is recorded with subtitles, you can use the Subtitle feature to view the subtitles on-screen. By default, subtitles are off. The info banner will display Subtitle Off. 4. To display subtitles, press the Subtitle button again.
D VD Operations DVD System Setup System operation will define the setting of the set; these definitions will be stored until you change them again. General Steps of Setup Menu 1. Pause or Stop the player. Press SETUP on the remote control. as below. The main menu will be shown 2. Press the/X / V button to select the Icon of the desired section, e.g. "TV System" and press > button to open that section. 3. Press/X / V to select the desired feature and again press > button to open that section. 4.
D VD Operations "0000". Using the/k / V enter "0000". You will see a new password number. lock field, the lock symbol Please remember or write button, move the highlight to "PASSWORD", press > the button and the padlock symbol open. You may now change the RATING or put in If the Lock symbol is BLUE you must press > the button to enter the will change to YELLOW, you may now enter a new 4 digit number. down the new Password and keep safe.
D VD Operations Disc Care About Disc Terms Title Generally, pictures or music compressed on a DVD are divided into several sections, "title". Chapter The smaller section unit of picture or music in a DVD under the title, usually one title is comprised of one or more chapters and each of them is numbered for easy searching, but some discs may not have a recording chapter. Track A segment of picture or music on a CD, Each track is numbered for searching.
Sim_le Troubleshootin_ Simple Troubleshooting If the display fails or performance dramatically deteriorates check the Display in accordance with the following instructions.Remember to check the peripherals topinpiont the source of the failure. If the display still fails to perform as expected,connect No power - Check all connections your helpline for assistance. to the TV. - Press either the power button or the Standby button on the Remote control.
Technical S_ec_cations Technical Specifications 24 inch (diagonal) 250 cd/m 2 1000:1 1920x1080 1 1 1 1 2 1 1 1 1 DC 12V 5A 60W * Product specifications and appearance are subject to change without 29 notice.
VIORE TMLIMITED WARRANTY FLAT PANEL TELEVISION This VIORE brand Product, as supplied and distributed by VIORE and delivered new in the original carton to the original purchaser is warranted by VlORE against manufacturing defects in materials and workmanship for a limited warranty period of one (1) year on parts and labor. However, there will be only a 90 day parts and labor limited warranty for commercial use.
VIORE, Inc.
