Viking Installation Guide Viking Range Corporation 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-VIKING1 (845-4641) or visit the Viking Web site at vikingrange.
IMPORTANT - PLEASE READ AND FOLLOW BASIC SPECIFICATIONS AND DIMENSIONS Make sure that incoming voltage is the same as unit rating. An electric rating plate specifying voltage, frequency, wattage, amperage, and phase is attached to the product. DESCRIPTION VCWB300 Overall Width 30” (76.2 cm) Overall Height from Bottom Min. 82-3/4” (210.2 cm) to Max. 84-1/16” (213.5 cm) Overall Depth from Rear To rear edge of side trim To front of top grille To end of handle bracket Cutout Width 29-1/2” (74.
FEATURES OF YOUR WINE CELLAR SITE PREPARATIONS AND CONSIDERATIONS PROFESSIONAL MODEL 30” W. FULL HEIGHT WINE CELLAR CABINET OPENING DIMENSIONS 1. 2. 3. 4. 5. 6. 7. TriTemp™ storage system Electronic control center Convertible display shelves (2) Extendable shelves (13) Energy efficient and UV resistant glass doors Low intensity lighting Black interior 8. 9. 10. 11. 12.
SITE PREPARATIONS AND CONSIDERATIONS AREA REQUIREMENTS DESIGNER/FULL OVERLAY MODEL 30” W. FULL HEIGHT WINE CELLAR CABINET OPENING DIMENSIONS Verify the following: •Wine cellar can fit into residence and can be moved around corners and through doorways. •Floors can support wine cellar’s weight plus wine weight (approximately 1200 pounds total). •Remove anything attached to rear or side walls that can obstruct wine cellar installation. •Cutout dimensions are accurate.
WINE CELLAR OVERALL DIMENSIONS - PROFESSIONAL MODEL CABINET INFORMATION - PROFESSIONAL MODEL Professional models fit “semi-flush” in standard 24” (61.0 cm) deep cabinet openings. The door face protrudes 2-5/16” (5.9 cm) from the cabinet face. The handle protrudes an additional 2-1/2” (6.4 cm) into the room 29-1/2” (90.2 cm) 29-1/2” (90.2 cm) Wall Wall 3/4” (1.9 cm) Full end panel 1-13/16” (4.6 cm) 24” (61.0 cm) Standard cabinet depth 2-5/16” (5.9 cm) Offset 5/16” (0.8 cm) 1-13/16” (4.
CABINET INFORMATION - PROFESSIONAL (continued) CUSTOM SIDE PANEL DIMENSIONS - PROFESSIONAL MODEL For 3/4” (1.9 cm) Side Panels 29-1/2” (90.2 cm) Wall 3/4” (1.9 cm) THICK END PANEL 3/4” (1.9 cm) Full end panel 1-13/16” (4.6 cm) space if 24” (61.0 cm) standard cabinet depth used 3/16” (0.5 cm) 3/16” (0.5 cm) THICK BACK FILLER PANEL 3/4” (1.9 cm) 24” (61.0 cm) Standard cabinet depth 3/16” (0.5 cm) 22-3/8” (56.9 cm) 22-3/8” (56.9 cm) 3/4” (1.9 cm) 6” (15.2 cm) 6” (15.2 cm) 5/32” (0.
WINE CELLAR OVERALL DIMENSIONS - DESIGNER MODEL TOP VIEW SIDE VIEW 29” (73.7 cm) CABINET INFORMATION - DESIGNER MODEL 24-1/32” (61.0 cm) TO FRONT OF GRILLE 4-17/32” (11.5 cm) Designer models fit “flush” in standard 24” (61.0 cm) deep cabinet openings with no protrusion into the room except 2-1/2” (6.3 cm) handle depth. 1/8” (.3 cm) 1-9/32” (3.3 cm) 30” (76.2 cm) 30” (76.2 cm) WALL WALL 9-3/8” (23.8 cm) 1” (2.5 cm) 3/4” (1.9 cm) FULL END PANEL 3/4” (1.9 cm) FULL END PANEL 25” (63.
CABINET INFORMATION - DESIGNER (continued) OVERALL DIMENSIONS - FULL OVERLAY MODEL 30” (76.2 cm) WALL TOP VIEW 3/4” (1.9 cm) SPACE IF 24” (61.0 cm) STANDARD CABINET DEPTH IS USED SIDE VIEW 29” (73.7 cm) 4-17/32” (11.5 cm) 24-3/4” (62.9 cm) TO FRONT OF GRILLE 1/8” (0.3 cm) 1-9/32” (3.3 cm) 9-3/8” (23.8 cm) 24” (61.0 cm) STANDARD CABINET DEPTH 24-3/4” (62.9cm) 30” (76.2 cm) SIDE TRIM FRONT VIEW 30” (76.2 cm) DOOR 9-5/8” (24.
CABINET INFORMATION - FULL OVERLAY MODEL CABINET INFORMATION - FULL OVERLAY (continued) Full overlay models, (with 3/4” [1.9 cm] thick panels and custom handles locally supplied), fit flush in 25” (63.5 cm) deep (countertop depth) cabinet openings with no protrusion into room except custom handles. Full overlay models can be installed in standard 24” (61.0 cm) deep openings. However, the door faces and top ventilation grille will protrude 3/4” (1.
CUSTOM SIDE PANEL DIMENSIONS - DESIGNER/FULL OVERLAY CUSTOM DOOR PANEL DIMENSIONS - FULL OVERLAY MODEL For 3/4” (1.9 cm) Side Panels NOTE: Adding a 3/4” (1.9 cm) side panel adds an additional 3/4” (1.9 cm) to the overall width of the product for each side panel used. Requires side panel hardware kit (Kit model number - SPHKDS) Z-BRACKET 1” (2.5 cm) 3/4” (1.9 cm) END PANEL 1/4” (0.6 cm) BACK FILLER PANEL 21-3/4” (55.2 cm) 1/4” (0.6 cm) 1” (2.5 cm) 1/4” (0.6 cm) 21-3/4” (55.2 cm) 1” (2.5 cm) 1” (2.
DOOR PANEL INSTALLATION - FULL OVERLAY MODEL CUSTOM WOOD FACINGS DIMENSIONS Panels must not weigh more than 50 pounds per door. Each wine rack has a wood facing which can be removed. The facings can be stained, painted, or removed and replaced with alternative wood facings. NOTE: A scrap sample should be tested in the unit before attaching permanent changes to your wine cellar fronts. Some paints and/or stains can cause undesirable odors.
WINE CELLAR INSTALLATION HOME SECURITY SYSTEM CONNECTION WARNING TIP OVER HAZARD Wine cellar is top heavy and tips easily when not completely installed. Keep door closed and shelves in place until wine cellar is completely installed and secured per installation instructions. Use two or more people to move and install wine cellar. Failure to do so can result in death or serious injury. WARNING Use two or more people to move and install wine cellar.
WARNING Electrical Shock Hazard Disconnect power at breaker or turn power disconnect switch to OFF position before performing any installation procedure. Failure to do so can result in death or electrical shock. SECURING THE WINE CELLAR (3 OPTIONS) OPTION 1 If a solid soffit is 1” (2.5 cm) or less above the wine cellar, anti-tip boards are not required. To secure the wine cellar raise unit until compartment is firmly seated under the soffit.
KICKPLATE INSTALLATION The kickplate consists of a two (2) part assembly: one top louvered panel and one bottom solid panel. Install the kickplate with louvered section on the top. Flooring must allow the kickplate to be removed. See “Site Preparations” for height clearance (pages 5 and 6). To install: 1. Insert the bottom (solid) panel into the open end of the top (louvered) panel. The holes in the bottom panel should line up with the slots in the top panel. 2.
