Viking Use/Installation Guide Viking Range Corporation 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information call 1-888-VIKNG1 (845-4641) or visit the Viking Web Site at vikingrange.
UNDERCOUNTER CABINET CUTOUT Retain for Future Reference IMPORTANT - PLEASE READ AND FOLLOW • • • • • Before beginning, please read these instructions completely and carefully. Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty. Please observe all local and national codes and ordinances. Please ensure that this product is properly grounded.
SPECIFICATIONS/DIMENSIONS PROFESSIONAL Basic Electric Data •115 VAC/60 Hz •Maximum amps - 3.3 •Approximate Shipping Weight - 180 lbs. (81.8 kg) Side View Front View 46-7/8” (119.0 cm) Min. 34” (86.4 cm) to Max. 34-3/4” (88.3 cm) with leveling legs fully extended. 30-3/4” (78.1 cm) 22” (55.9 cm) 23-7/8” (60.6 cm) 24-3/8” (61.9 cm) 26-7/8” (68.3 cm) 48-3/4” (123.
SPECIFICATIONS/DIMENSIONS DESIGNER Basic Electric Data •115 VAC/60 Hz •Maximum amps - 3.3 •Approximate shipping weight - 180 lbs. (81.8 kg) Side View Front View 46-1/2” (118.1 cm) Min. 34” (86.4 cm) to Max. 34-3/4” (88.3 cm) with leveling legs fully extended. 30-3/4” (78.1 cm) 22” (55.9 cm) 23-7/8” (60.6 cm) 24-3/8” (61.9 cm) 26-7/8” (68.3 cm) 48-3/4” (123.
GENERAL INFORMATION INSTALLING ANTI-TIP DEVICE Unpack 1. Remove banding from bottom of carton. Lift carton up and off of the unit. 2. Remove all tape and packaging material from the outside and inside of the cabinet. 3. Keep all carton packaging until your unit has been thoroughly inspected and found to be in good condition. AREA REQUIREMENTS Units Certified for Indoor Use - (black outer cabinet) MUST BE INSTALLED IN AN AREA PROTECTED FROM THE ELEMENTS, SUCH AS WIND, RAIN, WATER (SPRAY OR DRIP). 1.
FULL OVERLAY PANEL INSTALLATION FULL OVERLAY PANEL INSTALLATION Step #1 1. A #10 pan head wood screw should be used to properly secure the overlay panel. A total of 8 screws will be needed. 2. Use only pan head screws. 3. Do not select a screw that is longer than the wood thickness of the screw locations. 4. Use recommended pilot holes for the frame material. (Use chart below.
FULL OVERLAY PANEL INSTALLATION (con’t) ELECTRICAL CONNECTION Step #3 Sizing the Overlay Panel WARNING ELECTRICAL SHOCK HAZARD Failure to follow these instructions could result in fire or electrical shock. Power Supply Electrical Requirements with 3-prong A 115 volt, 60 Hz, AC only 15 amp fused electrical supply is required. (A time delay grounding plug fuse or circuit breaker is recommended.) It is recommended that a separate circuit, serving only this appliance, be provided. 23-5/8” (60.
SETTING THE CONTROLS The temperature of our drawer unit ranges from 32°F to 45°F (0°C to 7°C).
INTERIOR LIGHT ENERGY SAVING TIPS WARNING CAUTION ELECTRICAL SHOCK HAZARD Failure to disconnect the power cord when changing the light bulb may result in electrical shock. Never pour liquids directly onto light assembly. The following suggestions will minimize the cost of operating your refrigeration appliance. 1. Do not install your appliance next to a hot appliance, (cooker, dishwasher, etc.), heating air duct or other heat sources. 2. Install product out of direct sunlight. 3.
CLEANING AND MAINTENANCE TROUBLESHOOTING CHART Any piece of equipment works better and lasts longer when maintained properly and kept clean. Condenser The condenser underneath the cabinet does not require frequent cleaning; however, satisfactory cooling depends on adequate ventilation over this heat exchanger. It is recommended to annually clean the condenser by vacuuming and brushing.
SERVICE DIAGNOSTICS TruProtect™ “Advanced” Function “Quick” Reference 38 ˚F ON OFF WARMER SET TruProtect System ˚̊F/C COLDER Show Room Mode HIGH/LOW TEMP - Red ALARMS OFF - Steady Amber PRESS ON/OFF - Reset PRESS AND HOLD Function POWER FAILURE - Flashing Amber Control Confirmation/Comment Function Access Show Room Mode will disable the refrigerator system and fans while allowing the internal lights, display and user interface panel to function.
ENERGY SAVING TIPS •Reduce drawer openings. •Close the drawer as soon as you can. •Keep the condenser coils on bottom of the unit clean. (See “Cleaning and Maintenance”.) •Adjust the temperature control to a warmer setting when practical. •Do not put hot foods in the unit. •Install unit away from the stove or other heat sources.
UNDERCOUNTER/FREESTANDING REFRIGERATED DRAWER WARRANTY (Units certified for Outdoor Use) ONE YEAR FULL WARRANTY Built-in/freestanding undercounter refrigerated drawers and all of their components and accessories, except as detailed below*, are warranted to be free from defects in material or workmanship under normal household use for a period of one (1) year from the date of original retail purchase.
26 27
