Specifications

1
1
6
6
0
0
0
0
A
A
E
E
m
m
e
e
r
r
g
g
e
e
n
n
c
c
y
y
P
P
h
h
o
o
n
n
e
e
B
B
o
o
a
a
r
r
d
d
P
P
r
r
o
o
g
g
r
r
a
a
m
m
m
m
i
i
n
n
g
g
8
The 1600A Series emergency phones can be programmed from any Touch Tone phone using a C.O. line, analog
PABX/KSU station, or a DLE-200B Line Simulator. For more information on the DLE-200B, see DOD# 605.
A. Accessing the Programming Mode
Step 1. Move DIP switch 2 to the ON position (sets unit to answer incoming calls, see section J).
Step 2. From a Touch Tone phone call the line attached to the 1600A Series phone.
Step 3. When the 1600A Series phone answers, enter the 6-digit security code (factory set to 845464, see section C). A
double beep should then be heard indicating you have entered the programming mode.
2. Without the Security Code
1. Using the Security Code
Step 1. Move DIP switch 2 to the ON position (sets unit to answer incoming calls, see section J).
Step 2. Move DIP switch 3 to the OFF position (incoming calls enter Programming without security code, see section J).
Step 3. From a Touch Tone phone call the line attached to the 1600A Series phone.
Step 4. When the 1600A Series answers, a double beep will be heard and will automatically enter the programming mode.
Step 5. When finished programming, move DIP switch 3 back to the ON position (see section J).
Warning: Failure to do step 5 above will cause the 1600A Series phone to call Viking Technical Support instead of your programmed number.
Note: If a valid memory position is entered, a double beep will be heard, four beeps indicate an error.
B. Quick Programming Features
First emergency speed dial number .........................................................................
Second emergency speed dial number ...................................................................
Third emergency speed dial number .......................................................................
Fourth emergency speed dial number .....................................................................
Fifth emergency speed dial number .........................................................................
Central station receiver number ...............................................................................
Central station voice number ...................................................................................
First “Info” speed dial number (E-1600A-BLT2-EWP) .............................................
Second “Info” speed dial number (E-1600A-BLT2-EWP only) .................................
Third “Info” speed dial number (E-1600A-BLT2-EWP only) .....................................
Voice announcer/miscellaneous options (factory set to 000210) .............................
Timing/Dialing options (factory set to 234111) .........................................................
Security code (factory set to 845464) ......................................................................
Identification number (factory cleared) ....................................................................
Second central station identification number (factory cleared) .................................
To add a
Q at any point in the dialing string ..............................................................
To add a # at any point in the dialing string ..............................................................
To add a four second pause at any point in the dialing string ...................................
To switch to pulse dialing at any point in the dialing string ........................................
To clear any speed dial number ...............................................................................
Diagnostic tones (used to check mic and speaker operation) ..................................
Exit programming and disconnect ...........................................................................
Reset all programming to factory default settings ....................................................
Note: A double beep indicates a valid memory position, four beeps indicate an error.
0-20 digits
0-20 digits
0-20 digits
0-20 digits
0-20 digits
0-20 digits
0-20 digits
0-20 digits
0-20 digits
0-20 digits
6 digits
6 digits
6 digits
0-20 digits
0-20 digits
QQ
Q#
Q7
Q6
(no digits)
Q0
#7
###
#00
#01
#02
#03
#04
#05
#06
#07
#08
#09
#17
#18
#19
#20
#21
#00 - #09
Enter Digits
then
then
then
then
then
then
then
then
then
then
then
then
then
then
then
then
- then -
Enter Memory Location